main
Ray
Publish 0.1.0
f7cc824
ADM1070ARTZ-REEL7
Analog Devices · Surge Suppressors · SOT-23-6
ADM1070ARTZ-REEL7 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SENSE | input | Connects to the external FET source; the voltage across the sense resistor between SENSE and VEE is monitored, and when it reaches 100 mV for tON the regulator reduces the gate voltage, and tying SENSE to VEE turns current monitoring off. |
| 2 | VEE | power_in | Device negative supply voltage, which should be connected to the lower potential of the power supply. |
| 3 | VIN | power_in | Shunt-regulated on-chip supply, nominally VEE + 12.3 V, that must be current-fed through a dropper resistor from the higher supply potential; the device is undervoltage-locked out below 8.5 V. |
| 4 | TIMER | input | Sets the oscillator frequency and therefore the timing functions through an external capacitor to VEE, and tying the pin directly to VEE selects the internal default timing. |
| 5 | UV/OV | input | Input for undervoltage and overvoltage detection, where the gate is driven low if the voltage falls below 0.86 V or rises above 1.97 V, and R1/R2 = 40 gives an operating range of -36 V to -77 V. |
| 6 | GATE | output | Drives the external FET gate, being pulled low on an overvoltage or undervoltage fault or a current fault lasting longer than tON, and reaching a typical high level of 12 V when the FET is fully enhanced. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | TVS/Fuse/Board Level Protection |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum Voltage Range | -200 | -48 | -20 | V | Limited by Voltage Capability of External Components* | 2 | |
| Typical Operating Voltage Range | -77 | -48 | -36 | V | RDROP = 16 kΩ, R1/R2 = 40* | 2 | |
| Operating Supply Voltage Range | VSS | 11.5 | 12.3 | 13 | V | ISS = 1.5 mA to 4.25 mA | 2 |
| Quiescent Supply Current | ISS | 0.4 | 0.85 | 1.3 | mA | VSS = 11.5 V | 2 |
| Maximum Shunt Supply Voltage | VSS | 12.5 | 14 | V | ISS = 20 mA | 2 | |
| Undervoltage Lockout | VLKO | 7 | 8.5 | 10.5 | V | 2 | |
| Undervoltage Falling Threshold | VUVF | 0.81 | 0.86 | 0.91 | V | 2 | |
| Undervoltage Rising Threshold | VUVR | 0.86 | 0.91 | 0.96 | V | 2 | |
| Overvoltage Falling Threshold | VOVF | 1.85 | 1.93 | 2.01 | V | 2 | |
| Overvoltage Rising Threshold | VOVR | 1.89 | 1.97 | 2.05 | V | 2 | |
| Power-On Reset Delay | tPOR | 1.1 | 1.7 | 2.3 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 2 |
| Power-On Reset Delay | tPOR | 0.9 | 1.21 | 1.51 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF) | 2 |
| Voltage Fault Filter Time (UV/OV Out of Voltage Window) | tFLT | 1.1 | 1.7 | 2.3 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 2 |
| Voltage Fault Filter Time (UV/OV Out of Voltage Window) | tFLT | 0.9 | 1.21 | 1.51 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF) | 2 |
| Maximum Gate Voltage | VGMAX | 11 | 12 | 13 | V | IGATE = -1 µA | 2 |
| Minimum Gate Voltage | VGMIN | 0 | 50 | mV | IGATE = 1 µA | 2 | |
| Pull-Up Current | IGUP | -20 | -40 | -55 | µA | VGATE = 0 V to 9 V, VSENSE = 0 | 2 |
| Pull-Down Current | IGDP | 10 | 30 | mA | VGATE = VSS | 2 | |
| Analog Current Limit Voltage (Rising) | VLIM | 90 | 100 | 110 | mV | IGATE = 0 µA to -15 µA | 2 |
| Circuit Breaker Limit Voltage (Rising) | 75 | 88 | 100 | mV | 2 | ||
| Circuit Breaker Limit Voltage (Falling) | 60 | 79 | 95 | mV | 2 | ||
| Fast Current Limit Voltage | 107 | 126 | 145 | mV | 2 | ||
| Control Loop Transconductance | dIGATE/dVSENSE | 1.5 | 2.75 | 4 | µA/mV | IGATE < 30 µA, TA = 25°C | 2 |
| Maximum Current Limit On Time | tLIMITON | 10 | 14 | 18 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 2 |
| Maximum Current Limit On Time | tLIMITON | 7.4 | 9.9 | 12.4 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF) | 2 |
| Current Limit PWM Off Time | 320 | 450 | 580 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF)* | 2 | |
| Current Limit PWM Off Time | 240 | 320 | 400 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF)* | 2 | |
| Continuous Short Circuit Time before Latched Shutdown | tSHORT | 2100 | 2800 | 3500 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 3 |
| Continuous Short Circuit Time before Latched Shutdown | tSHORT | 1500 | 2000 | 2500 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF)* | 3 |
| Operating Sense Voltage Range | VSOP | 0 | 0.11 | V | 3 | ||
| Input Current | ISENSE | -500 | 500 | µA | VSENSE = -2 V to +2 V | 3 | |
| External/Internal Selection Threshold | VTIMERTHEI | 0.3 | 0.45 | 0.6 | V | 3 | |
| High Trip Threshold | VTIMERTHH | 3 | 3.5 | 4 | V | 3 | |
| Low Trip Threshold | VTIMERTHL | 1.2 | 1.5 | 1.8 | V | 3 | |
| Pull-Down Current | ITIMERDN | 15 | 24 | 31 | µA | VTIMER > VTIMERTHH | 3 |
| Pull-Up Current | ITIMERUP | -15 | -24 | -31 | µA | VTIMERTHEI < VTIMER < VTIMERTHL | 3 |
| Start-Up Current | ITIMERSTART | -12 | -19 | -26 | µA | VTIMER < VTIMERTHEI | 3 |
| Supply Voltage (VDD-VEE) | VDD-VEE | -200 | -0.3 | V | 3 | ||
| Maximum Shunt Supply Voltage | VSS | 16 | V | 3 | |||
| SENSE Pin | -2 | 16 | V | 3 | |||
| GATE Pin | -0.3 | 16 | V | 3 | |||
| UV/OV Pin | -0.3 | 15 | V | 3 | |||
| TIMER Pin | -0.3 | 10 | V | 3 | |||
| Maximum Junction Temperature | 125 | °C | 3 | ||||
| Temperature Range | -40 | 85 | °C | 3 | |||
| Continuous Power Dissipation | 282 | mW | 3 | ||||
| Storage Temperature Range | -65 | 150 | °C | 3 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | Soldering, 10 sec | 3 | |||
| Thermal Resistance, Junction-to-Ambient, 6-Lead SOT-23 | JA | 226.6 | °C/W | 6-Lead SOT-23 Package | 3 | ||
| Thermal Resistance, Junction-to-Case, 6-Lead SOT-23 | JC | 91.99 | °C/W | 6-Lead SOT-23 Package | 3 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
ADM1070ARTZ-REEL7 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
adm1070artz-etched.step/adm1070artz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adm1070artz.step/adm1070artz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
a60b82e24cb32562, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# ADM1070ARTZ-REEL7
**Analog Devices** · Surge Suppressors · SOT-23-6
ADM1070ARTZ-REEL7 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SENSE | input | Connects to the external FET source; the voltage across the sense resistor between SENSE and VEE is monitored, and when it reaches 100 mV for tON the regulator reduces the gate voltage, and tying SENSE to VEE turns current monitoring off. |
| 2 | VEE | power_in | Device negative supply voltage, which should be connected to the lower potential of the power supply. |
| 3 | VIN | power_in | Shunt-regulated on-chip supply, nominally VEE + 12.3 V, that must be current-fed through a dropper resistor from the higher supply potential; the device is undervoltage-locked out below 8.5 V. |
| 4 | TIMER | input | Sets the oscillator frequency and therefore the timing functions through an external capacitor to VEE, and tying the pin directly to VEE selects the internal default timing. |
| 5 | UV/OV | input | Input for undervoltage and overvoltage detection, where the gate is driven low if the voltage falls below 0.86 V or rises above 1.97 V, and R1/R2 = 40 gives an operating range of -36 V to -77 V. |
| 6 | GATE | output | Drives the external FET gate, being pulled low on an overvoltage or undervoltage fault or a current fault lasting longer than tON, and reaching a typical high level of 12 V when the FET is fully enhanced. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | TVS/Fuse/Board Level Protection |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum Voltage Range | | -200 | -48 | -20 | V | Limited by Voltage Capability of External Components* | 2 |
| Typical Operating Voltage Range | | -77 | -48 | -36 | V | RDROP = 16 kΩ, R1/R2 = 40* | 2 |
| Operating Supply Voltage Range | VSS | 11.5 | 12.3 | 13 | V | ISS = 1.5 mA to 4.25 mA | 2 |
| Quiescent Supply Current | ISS | 0.4 | 0.85 | 1.3 | mA | VSS = 11.5 V | 2 |
| Maximum Shunt Supply Voltage | VSS | 12.5 | | 14 | V | ISS = 20 mA | 2 |
| Undervoltage Lockout | VLKO | 7 | 8.5 | 10.5 | V | | 2 |
| Undervoltage Falling Threshold | VUVF | 0.81 | 0.86 | 0.91 | V | | 2 |
| Undervoltage Rising Threshold | VUVR | 0.86 | 0.91 | 0.96 | V | | 2 |
| Overvoltage Falling Threshold | VOVF | 1.85 | 1.93 | 2.01 | V | | 2 |
| Overvoltage Rising Threshold | VOVR | 1.89 | 1.97 | 2.05 | V | | 2 |
| Power-On Reset Delay | tPOR | 1.1 | 1.7 | 2.3 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 2 |
| Power-On Reset Delay | tPOR | 0.9 | 1.21 | 1.51 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF) | 2 |
| Voltage Fault Filter Time (UV/OV Out of Voltage Window) | tFLT | 1.1 | 1.7 | 2.3 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 2 |
| Voltage Fault Filter Time (UV/OV Out of Voltage Window) | tFLT | 0.9 | 1.21 | 1.51 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF) | 2 |
| Maximum Gate Voltage | VGMAX | 11 | 12 | 13 | V | IGATE = -1 µA | 2 |
| Minimum Gate Voltage | VGMIN | 0 | | 50 | mV | IGATE = 1 µA | 2 |
| Pull-Up Current | IGUP | -20 | -40 | -55 | µA | VGATE = 0 V to 9 V, VSENSE = 0 | 2 |
| Pull-Down Current | IGDP | 10 | | 30 | mA | VGATE = VSS | 2 |
| Analog Current Limit Voltage (Rising) | VLIM | 90 | 100 | 110 | mV | IGATE = 0 µA to -15 µA | 2 |
| Circuit Breaker Limit Voltage (Rising) | | 75 | 88 | 100 | mV | | 2 |
| Circuit Breaker Limit Voltage (Falling) | | 60 | 79 | 95 | mV | | 2 |
| Fast Current Limit Voltage | | 107 | 126 | 145 | mV | | 2 |
| Control Loop Transconductance | dIGATE/dVSENSE | 1.5 | 2.75 | 4 | µA/mV | IGATE < 30 µA, TA = 25°C | 2 |
| Maximum Current Limit On Time | tLIMITON | 10 | 14 | 18 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 2 |
| Maximum Current Limit On Time | tLIMITON | 7.4 | 9.9 | 12.4 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF) | 2 |
| Current Limit PWM Off Time | | 320 | 450 | 580 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF)* | 2 |
| Current Limit PWM Off Time | | 240 | 320 | 400 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF)* | 2 |
| Continuous Short Circuit Time before Latched Shutdown | tSHORT | 2100 | 2800 | 3500 | ms | TIMER Pin Tied to VEE (VUVR < UV/OV < VOVF) | 3 |
| Continuous Short Circuit Time before Latched Shutdown | tSHORT | 1500 | 2000 | 2500 | ms | CTIMER = 470 pF (VUVR < UV/OV < VOVF)* | 3 |
| Operating Sense Voltage Range | VSOP | 0 | | 0.11 | V | | 3 |
| Input Current | ISENSE | -500 | | 500 | µA | VSENSE = -2 V to +2 V | 3 |
| External/Internal Selection Threshold | VTIMERTHEI | 0.3 | 0.45 | 0.6 | V | | 3 |
| High Trip Threshold | VTIMERTHH | 3 | 3.5 | 4 | V | | 3 |
| Low Trip Threshold | VTIMERTHL | 1.2 | 1.5 | 1.8 | V | | 3 |
| Pull-Down Current | ITIMERDN | 15 | 24 | 31 | µA | VTIMER > VTIMERTHH | 3 |
| Pull-Up Current | ITIMERUP | -15 | -24 | -31 | µA | VTIMERTHEI < VTIMER < VTIMERTHL | 3 |
| Start-Up Current | ITIMERSTART | -12 | -19 | -26 | µA | VTIMER < VTIMERTHEI | 3 |
| Supply Voltage (VDD-VEE) | VDD-VEE | -200 | | -0.3 | V | | 3 |
| Maximum Shunt Supply Voltage | VSS | | | 16 | V | | 3 |
| SENSE Pin | | -2 | | 16 | V | | 3 |
| GATE Pin | | -0.3 | | 16 | V | | 3 |
| UV/OV Pin | | -0.3 | | 15 | V | | 3 |
| TIMER Pin | | -0.3 | | 10 | V | | 3 |
| Maximum Junction Temperature | | | | 125 | °C | | 3 |
| Temperature Range | | -40 | | 85 | °C | | 3 |
| Continuous Power Dissipation | | | | 282 | mW | | 3 |
| Storage Temperature Range | | -65 | | 150 | °C | | 3 |
| Lead Temperature (Soldering, 10 sec) | | | | 300 | °C | Soldering, 10 sec | 3 |
| Thermal Resistance, Junction-to-Ambient, 6-Lead SOT-23 | JA | | 226.6 | | °C/W | 6-Lead SOT-23 Package | 3 |
| Thermal Resistance, Junction-to-Case, 6-Lead SOT-23 | JC | | 91.99 | | °C/W | 6-Lead SOT-23 Package | 3 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `ADM1070ARTZ-REEL7`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `adm1070artz-etched.step` / `adm1070artz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `adm1070artz.step` / `adm1070artz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1070.pdf) (16 pp, sha256 `a60b82e24cb32562`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/adm1070artz-datasheet.pdf)