main
History Download
Ray Publish 0.1.0 1175f41

AD8027ARTZ-R2

Analog Devices · Operational Amplifier · SOT-23-6

AD8027ARTZ-R2 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VOUT output Output voltage pin of the amplifier; the datasheet gives no further electrical limits for this pin.
2 -VS power_in Negative supply pin; the datasheet specifies a total supply range of 2.7 V to 12 V for the part.
3 +IN input Positive input pin of the amplifier; the datasheet gives no further electrical limits for this pin.
4 -IN input Negative input pin of the amplifier; the datasheet gives no further electrical limits for this pin.
5 DISABLE/SELECT input Power-down/select pin: the power-down function places the device into low power consumption mode, and the select function shifts the NPN/PNP input crossover point closer to either the positive or negative supply rail.
6 +VS power_in Positive supply pin; the datasheet specifies a total supply range of 2.7 V to 12 V for the part.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package SOT-23-6
Category Amplifiers
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
-3 dB Bandwidth 138 190 MHz G = +1, VOUT = 0.2 V p-p 3
-3 dB Bandwidth 20 32 MHz G = +1, VOUT = 2 V p-p 3
Input Offset Voltage 200 800 µV DISABLE/SELECT = tristate or open, PNP active 3
Input Offset Voltage 240 900 µV DISABLE/SELECT = high, NPN active 3
Input Bias Current 4 6 µA VCM = 0 V, NPN active 3
Input Bias Current -11 -8 µA VCM = 0 V, PNP active 3
Common-Mode Rejection Ratio 90 110 dB VCM = ±2.5 V 3
Input Common-Mode Voltage Range -5.2 5.2 V 3
Crossover High -3.9 -3.7 V Tristate < ±20 µA, TMIN to TMAX 3
Output Overdrive Recovery Time (Rising/Falling Edge) 40 45 ns Printed as 40/45 ns (rising/falling edge); VIN = +6 V to −6 V, G = −1 3
Power Supply Operating Range 2.7 12 V 4
Quiescent Current per Amplifier 6.5 8.5 mA 4
Quiescent Current per Amplifier (Disabled) 370 500 µA DISABLE/SELECT = low 4
Power Supply Rejection Ratio 90 110 dB VS ± 1 V 4
Supply Voltage 12.6 V 7
Differential Input Voltage -1.8 1.8 V 7
Storage Temperature Range -65 125 °C 7
Operating Temperature Range -40 125 °C 7
Lead Temperature Range (Soldering) 300 °C Soldering 10 sec 7
Junction Temperature 150 °C 7
Thermal Resistance, Junction-to-Ambient (θJA) θJA 170 °C/W 6-lead SOT-23, JEDEC standard 4-layer board 7
Crossover Low -3 V TMIN to TMAX 3
Disable Input Voltage -4.6 V TMIN to TMAX 3
Disable Switching Speed 980 ns 50% of input to <10% of final VOUT 3
Enable Switching Speed 45 ns 3
Short-Circuit Output Current 120 mA Sinking and sourcing 4
Off Isolation -49 dB VIN = 0.2 V p-p, f = 1 MHz, DISABLE/SELECT = low 4
Capacitive Load Drive 20 pF 30% overshoot 4
Input Offset Voltage Drift 1.5 µV/°C TMIN to TMAX 3
Input Impedance 6 MΩ 3
Input Capacitance 2 pF 3
-3 dB Bandwidth (0.1 dB flatness) 16 MHz Bandwidth for 0.1 dB Flatness, G = +2, VOUT = 0.2 V p-p 3
Slew Rate 90 V/µs G = +1, VOUT = 2 V step 3
Slew Rate 100 V/µs G = −1, VOUT = 2 V step 3
Settling Time to 0.1% 35 ns G = +2, VOUT = 2 V step 3
Spurious-Free Dynamic Range (SFDR) 120 dBc fC = 1 MHz, VOUT = 2 V p-p, RF = 24.9 Ω 3
Spurious-Free Dynamic Range (SFDR) 80 dBc fC = 5 MHz, VOUT = 2 V p-p, RF = 24.9 Ω 3
Input Voltage Noise 4.3 nV/√Hz f = 100 kHz 3
Input Current Noise 1.6 pA/√Hz f = 100 kHz 3
Differential Gain Error 0.1 % NTSC, G = +2, RL = 150 Ω 3
Differential Phase Error 0.2 Degrees NTSC, G = +2, RL = 150 Ω 3
Crosstalk, Output to Output -93 dB G = +1, RL = 100 Ω, VOUT = 2 V p-p, VS = ±5 V at 1 MHz 3

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: AD8027ARTZ-R2
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ad8027artz-r2-etched.step / ad8027artz-r2-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ad8027artz-r2.step / ad8027artz-r2.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (27 pp, sha256 b9958dce5bf5362c, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF