Generated by kicad-footprint-generator · KiCad file format 20260206
AD8027ARTZ-R2
Analog Devices · Operational Amplifier · SOT-23-6
AD8027ARTZ-R2 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | output | Output voltage pin of the amplifier; the datasheet gives no further electrical limits for this pin. |
| 2 | -VS | power_in | Negative supply pin; the datasheet specifies a total supply range of 2.7 V to 12 V for the part. |
| 3 | +IN | input | Positive input pin of the amplifier; the datasheet gives no further electrical limits for this pin. |
| 4 | -IN | input | Negative input pin of the amplifier; the datasheet gives no further electrical limits for this pin. |
| 5 | DISABLE/SELECT | input | Power-down/select pin: the power-down function places the device into low power consumption mode, and the select function shifts the NPN/PNP input crossover point closer to either the positive or negative supply rail. |
| 6 | +VS | power_in | Positive supply pin; the datasheet specifies a total supply range of 2.7 V to 12 V for the part. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | Amplifiers |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| -3 dB Bandwidth | 138 | 190 | MHz | G = +1, VOUT = 0.2 V p-p | 3 | ||
| -3 dB Bandwidth | 20 | 32 | MHz | G = +1, VOUT = 2 V p-p | 3 | ||
| Input Offset Voltage | 200 | 800 | µV | DISABLE/SELECT = tristate or open, PNP active | 3 | ||
| Input Offset Voltage | 240 | 900 | µV | DISABLE/SELECT = high, NPN active | 3 | ||
| Input Bias Current | 4 | 6 | µA | VCM = 0 V, NPN active | 3 | ||
| Input Bias Current | -11 | -8 | µA | VCM = 0 V, PNP active | 3 | ||
| Common-Mode Rejection Ratio | 90 | 110 | dB | VCM = ±2.5 V | 3 | ||
| Input Common-Mode Voltage Range | -5.2 | 5.2 | V | 3 | |||
| Crossover High | -3.9 | -3.7 | V | Tristate < ±20 µA, TMIN to TMAX | 3 | ||
| Output Overdrive Recovery Time (Rising/Falling Edge) | 40 | 45 | ns | Printed as 40/45 ns (rising/falling edge); VIN = +6 V to −6 V, G = −1 | 3 | ||
| Power Supply Operating Range | 2.7 | 12 | V | 4 | |||
| Quiescent Current per Amplifier | 6.5 | 8.5 | mA | 4 | |||
| Quiescent Current per Amplifier (Disabled) | 370 | 500 | µA | DISABLE/SELECT = low | 4 | ||
| Power Supply Rejection Ratio | 90 | 110 | dB | VS ± 1 V | 4 | ||
| Supply Voltage | 12.6 | V | 7 | ||||
| Differential Input Voltage | -1.8 | 1.8 | V | 7 | |||
| Storage Temperature Range | -65 | 125 | °C | 7 | |||
| Operating Temperature Range | -40 | 125 | °C | 7 | |||
| Lead Temperature Range (Soldering) | 300 | °C | Soldering 10 sec | 7 | |||
| Junction Temperature | 150 | °C | 7 | ||||
| Thermal Resistance, Junction-to-Ambient (θJA) | θJA | 170 | °C/W | 6-lead SOT-23, JEDEC standard 4-layer board | 7 | ||
| Crossover Low | -3 | V | TMIN to TMAX | 3 | |||
| Disable Input Voltage | -4.6 | V | TMIN to TMAX | 3 | |||
| Disable Switching Speed | 980 | ns | 50% of input to <10% of final VOUT | 3 | |||
| Enable Switching Speed | 45 | ns | 3 | ||||
| Short-Circuit Output Current | 120 | mA | Sinking and sourcing | 4 | |||
| Off Isolation | -49 | dB | VIN = 0.2 V p-p, f = 1 MHz, DISABLE/SELECT = low | 4 | |||
| Capacitive Load Drive | 20 | pF | 30% overshoot | 4 | |||
| Input Offset Voltage Drift | 1.5 | µV/°C | TMIN to TMAX | 3 | |||
| Input Impedance | 6 | MΩ | 3 | ||||
| Input Capacitance | 2 | pF | 3 | ||||
| -3 dB Bandwidth (0.1 dB flatness) | 16 | MHz | Bandwidth for 0.1 dB Flatness, G = +2, VOUT = 0.2 V p-p | 3 | |||
| Slew Rate | 90 | V/µs | G = +1, VOUT = 2 V step | 3 | |||
| Slew Rate | 100 | V/µs | G = −1, VOUT = 2 V step | 3 | |||
| Settling Time to 0.1% | 35 | ns | G = +2, VOUT = 2 V step | 3 | |||
| Spurious-Free Dynamic Range (SFDR) | 120 | dBc | fC = 1 MHz, VOUT = 2 V p-p, RF = 24.9 Ω | 3 | |||
| Spurious-Free Dynamic Range (SFDR) | 80 | dBc | fC = 5 MHz, VOUT = 2 V p-p, RF = 24.9 Ω | 3 | |||
| Input Voltage Noise | 4.3 | nV/√Hz | f = 100 kHz | 3 | |||
| Input Current Noise | 1.6 | pA/√Hz | f = 100 kHz | 3 | |||
| Differential Gain Error | 0.1 | % | NTSC, G = +2, RL = 150 Ω | 3 | |||
| Differential Phase Error | 0.2 | Degrees | NTSC, G = +2, RL = 150 Ω | 3 | |||
| Crosstalk, Output to Output | -93 | dB | G = +1, RL = 100 Ω, VOUT = 2 V p-p, VS = ±5 V at 1 MHz | 3 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
AD8027ARTZ-R2 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ad8027artz-r2-etched.step/ad8027artz-r2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad8027artz-r2.step/ad8027artz-r2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (27 pp, sha256
b9958dce5bf5362c, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).