component
AD7621ASTZ
Public Made by Adomby adom
Analog Devices Analog To Digital Converters (ADCs), LQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownAD7621ASTZ
Analog Devices · Analog To Digital Converters (ADCs) · LQFP-48(7x7)
AD7621ASTZ from Analog Devices, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AGND | power_in | Analog power ground pin. |
| 2 | AVDD | power_in | Input analog power pin, nominally 2.5 V. |
| 3 | NC | unconnected | No connect. |
| 4 | BYTESWAP | input | Parallel mode selection (8-bit/16-bit): when high the LSB is output on D[15:8] and the MSB on D[7:0], when low the LSB is on D[7:0] and the MSB on D[15:8]. |
| 5 | OB/2C | input | Straight binary/binary twos complement output select: high gives straight binary, low inverts the MSB for twos complement output. |
| 6 | WARP | input | Conversion mode selection: WARP high with IMPULSE high selects wideband mode, WARP high with IMPULSE low selects warp mode, and WARP low with IMPULSE low selects normal mode. |
| 7 | IMPULSE | input | Conversion mode selection: IMPULSE high with WARP low selects impulse mode, a reduced power mode with power approximately proportional to sampling rate. |
| 8 | SER/PAR | input | Serial/parallel selection input: high selects the serial interface, low selects the parallel port. |
| 9 | D0 | output | Bit 0 of the parallel port data output bus. |
| 10 | D1 | output | Bit 1 of the parallel port data output bus. |
| 11 | D2/DIVSCLK[0] | bidirectional | Bit 2 of the parallel data output bus when SER/PAR is low; when SER/PAR is high, serial clock division selection input (otherwise high-impedance output in other serial modes). |
| 12 | D3/DIVSCLK[1] | bidirectional | Bit 3 of the parallel data output bus when SER/PAR is low; when SER/PAR is high, serial clock division selection input used to slow the internal serial clock in serial master read-after-convert mode. |
| 13 | D4/EXT/INT | bidirectional | Bit 4 of the parallel data output bus when SER/PAR is low; when SER/PAR is high, selects internal (low, master) or external (high, slave) serial data clock. |
| 14 | D5/INVSYNC | bidirectional | Bit 5 of the parallel data output bus when SER/PAR is low; when SER/PAR is high in serial master mode, selects SYNC active high (low) or active low (high). |
| 15 | D6/INVSCLK | bidirectional | Bit 6 of the parallel data output bus when SER/PAR is low; in all serial modes, inverts the SCLK signal. |
| 16 | D7/RDC/SDIN | bidirectional | Bit 7 of the parallel data output bus; in serial master mode selects read during convert (RDC high) or read after convert (low), and in serial slave mode is the SDIN daisy-chain data input. |
| 17 | OGND | power_in | Input/output interface digital power ground. |
| 18 | OVDD | power_in | Input/output interface digital power, nominally at the same supply as the host interface (2.5 V or 3 V). |
| 19 | DVDD | power_in | Digital power, nominally 2.5 V. |
| 20 | DGND | power_in | Digital power ground. |
| 21 | D8/SDOUT | output | Bit 8 of the parallel data output bus when SER/PAR is low; when SER/PAR is high, serial data output, MSB first, synchronized to SCLK. |
| 22 | D9/SCLK | bidirectional | Bit 9 of the parallel data output bus when SER/PAR is low; when SER/PAR is high, serial data clock input or output depending on EXT/INT. |
| 23 | D10/SYNC | output | Bit 10 of the parallel data output bus when SER/PAR is low; in serial master mode, frame synchronization output for use with the internal data clock. |
| 24 | D11/RDERROR | output | Bit 11 of the parallel data output bus when SER/PAR is low; in serial slave mode, incomplete read error flag pulsed high if a read is not completed before the current conversion completes. |
| 25 | D12 | output | Bit 12 of the parallel port data output bus. |
| 26 | D13 | output | Bit 13 of the parallel port data output bus. |
| 27 | D14 | output | Bit 14 of the parallel port data output bus. |
| 28 | D15 | output | Bit 15 of the parallel port data output bus. |
| 29 | BUSY | output | Busy output that goes high when a conversion starts and stays high until the data is latched; its falling edge can be used as a data ready clock. |
| 30 | DGND | power_in | Digital power ground. |
| 31 | RD | input | Read data: when CS and RD are both low, the parallel or serial output bus is enabled. |
| 32 | CS | input | Chip select: when CS and RD are both low the output bus is enabled, and CS also gates the external clock in slave serial mode. |
| 33 | RESET | input | Reset input: when high resets the AD7621 and aborts any conversion, falling edge enables calibration mode indicated by BUSY pulsing high; can be tied to DGND if unused. |
| 34 | PD | input | Power-down input: when high powers down the ADC, reducing power consumption and inhibiting conversions after the current one completes. |
| 35 | CNVST | input | Conversion start: a falling edge puts the internal sample-and-hold into hold and initiates a conversion. |
| 36 | AGND | power_in | Analog power ground pin. |
| 37 | REF | bidirectional | Reference output/input: produces 2.048 V when the internal reference and buffer are enabled, or accepts an external reference up to AVDD when they are disabled; decoupling is required in both cases. |
| 38 | REFGND | input | Reference input analog ground. |
| 39 | IN− | input | Differential negative analog input. |
| 40 | NC | unconnected | No connect. |
| 41 | AGND | power_in | Analog power ground pin. |
| 42 | AGND | power_in | Analog power ground pin. |
| 43 | IN+ | input | Differential positive analog input. |
| 44 | AVDD | power_in | Input analog power pin, nominally 2.5 V. |
| 45 | TEMP | output | Temperature sensor analog output. |
| 46 | REFBUFIN | bidirectional | Internal reference output (1.2 V typical bandgap, needs external decoupling) or reference buffer input, where 1.2 V applied produces 2.048 V on REF. |
| 47 | PDREF | input | Internal reference power-down input: low enables the internal reference, high powers it down so an external reference must be used. |
| 48 | PDBUF | input | Internal reference buffer power-down input: low enables the buffer (must be low when using the internal reference), high powers it down. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-48(7x7) |
| Category | Data Converters |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Integral Linearity Error | INL | -2 | 1 | 2 | LSB | VREF = 2.048 V, PDREF = high | 3 |
| Differential Linearity Error | DNL | -1 | 2 | LSB | VREF = 2.048 V, PDREF = high | 3 | |
| Zero Error | -30 | 30 | LSB | TMIN to TMAX | 3 | ||
| Gain Error | -0.38 | 0.38 | % of FSR | TMIN to TMAX | 3 | ||
| Signal-to-Noise | SNR | 88 | 90 | dB | fIN = 20 kHz, VREF = 2.5 V | 3 | |
| Signal-to-Noise | SNR | 86 | 88 | dB | fIN = 20 kHz, VREF = 2.048 V | 3 | |
| Signal-to-(Noise + Distortion) | SINAD | 87.5 | 89.8 | dB | fIN = 20 kHz, VREF = 2.5 V | 3 | |
| Internal Reference Output Voltage | REF | 2.038 | 2.048 | 2.058 | V | REF @ 25°C, PDREF = PDBUF = low | 3 |
| Operating Input Voltage | -0.1 | V | VIN+, VIN− to AGND | 3 | |||
| Analog Input CMRR | 55 | dB | fIN = 100 kHz | 3 | |||
| Throughput Rate (warp) | 0.001 | 3 | MSPS | Wideband warp, warp modes | 3 | ||
| Throughput Rate (normal) | 0 | 2 | MSPS | Normal mode | 3 | ||
| Throughput Rate (impulse) | 0 | 1.25 | MSPS | Impulse mode | 3 | ||
| External Reference Voltage Range | REF | 1.8 | 2.048 | 2.63 | V | PDREF = PDBUF = high; max printed as AVDD | 4 |
| REFBUFIN Input Voltage Range | 1.05 | 1.2 | 1.3 | V | PDREF = high, PDBUF = low | 4 | |
| Logic Input Low Voltage | VIL | -0.3 | 0.6 | V | 4 | ||
| Logic Input High Voltage | VIH | 1.7 | 5.25 | V | 4 | ||
| Input Leakage Low | IIL | -1 | 1 | μA | 4 | ||
| Input Leakage High | IIH | -1 | 1 | μA | 4 | ||
| Output Low Voltage | VOL | 0.4 | V | ISINK = 500 μA | 4 | ||
| Output High Voltage | VOH | 2 | V | ISOURCE = -500 μA; printed OVDD − 0.3 V | 4 | ||
| Analog Supply Voltage | AVDD | 2.37 | 2.5 | 2.63 | V | Specified performance | 4 |
| Digital Supply Voltage | DVDD | 2.37 | 2.5 | 2.63 | V | Specified performance | 4 |
| Interface Supply Voltage | OVDD | 2.3 | 3.6 | V | 4 | ||
| Power Dissipation, with internal reference | 70 | 86 | mW | 3 MSPS throughput | 4 | ||
| Power Dissipation, without internal reference | 65 | 80 | mW | 3 MSPS throughput | 4 | ||
| Power Dissipation, with internal reference | 42 | 55 | mW | 1.25 MSPS throughput | 4 | ||
| Power Dissipation, without internal reference | 37 | 50 | mW | 1.25 MSPS throughput | 4 | ||
| Power Dissipation in Power-Down Mode | 600 | μW | PD = high | 4 | |||
| Specified Temperature Range | -40 | 85 | °C | TMIN to TMAX | 4 | ||
| Convert Pulse Width | t1 | 15 | 70 | ns | 5 | ||
| CNVST Low to BUSY High Delay | t3 | 23 | ns | 5 | |||
| RESET Pulse Width | t9 | 15 | ns | 5 | |||
| External SCLK Period | t35 | 12.5 | ns | 6 | |||
| Analog Inputs to AGND | -0.3 | V | IN+, IN−, REF, REFBUFIN, TEMP, INGND, REFGND; printed AVDD + 0.3 V to AGND − 0.3 V | 7 | |||
| Supply Voltage AVDD, DVDD | -0.3 | 2.7 | V | 7 | |||
| Supply Voltage OVDD | -0.3 | 3.8 | V | 7 | |||
| Digital Inputs | -0.3 | 5.5 | V | 7 | |||
| PDREF, PDBUF current | -20 | 20 | mA | printed ±20 mA | 7 | ||
| Internal Power Dissipation | 700 | mW | 48-Lead LQFP, free air | 7 | |||
| Junction Temperature | 125 | °C | 7 | ||||
| Storage Temperature Range | -65 | 125 | °C | 7 | |||
| Thermal Resistance Junction to Ambient | θJA | 91 | °C/W | 48-Lead LQFP, free air | 7 | ||
| Thermal Resistance Junction to Case | θJC | 30 | °C/W | 48-Lead LQFP, free air | 7 | ||
| Resolution | 16 | Bits | 3 | ||||
| Transition Noise | 0.69 | LSB | VREF = 2.5 V | 3 | |||
| Zero Error Temperature Drift | 1 | ppm/°C | printed ±1 | 3 | |||
| Gain Error Temperature Drift | 2 | ppm/°C | printed ±2 | 3 | |||
| Internal Reference Temperature Drift | 7 | ppm/°C | -40°C to +85°C, printed ±7 | 3 | |||
| Operating Current AVDD | 25.2 | mA | 3 MSPS throughput, with internal reference | 4 |
CAD (KiCad official)
- Symbol:
AD7621ASTZ - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
ad7621astz-etched.step/ad7621astz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7621astz.step/ad7621astz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
e95a22543e657799, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).