component
AD7612BSTZ
Public Made by Adomby adom
Analog Devices Analog To Digital Converters (ADCs), LQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
ff73a70
AD7612BSTZ
Analog Devices · Analog To Digital Converters (ADCs) · LQFP-48(7x7)
AD7612BSTZ from Analog Devices, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AGND | power_in | Analog power ground pin and ground reference for all analog I/O, which should be connected to the analog ground plane and kept at the same potential as AGND, DGND and OGND. |
| 2 | AVDD | power_in | Analog power supply, nominally 4.75 V to 5.25 V, decoupled with 10 μF and 100 nF capacitors. |
| 3 | AGND | power_in | Analog power ground pin and ground reference for all analog I/O, which should be connected to the analog ground plane and kept at the same potential as AGND, DGND and OGND. |
| 4 | BYTESWAP | input | Parallel mode 8/16-bit byte-order select: when high the LSB is output on D[15:8] and the MSB on D[7:0], and when low the LSB is output on D[7:0] and the MSB on D[15:8]. |
| 5 | OB/2C | input | Output coding select: when high the output is straight binary, and when low the MSB is inverted to give twos complement output (this pin is a don't-care in serial software configuration mode). |
| 6 | WARP | input | Conversion mode select used with IMPULSE: WARP/IMPULSE low/low is normal, low/high is impulse, high/low is warp and high/high is normal (don't-care in serial software configuration mode). |
| 7 | IMPULSE | input | Conversion mode select used with WARP as defined for pin 6 (don't-care in serial software configuration mode). |
| 8 | SER/PAR | input | Serial/parallel selection: when low the parallel mode is selected, and when high the serial modes are selected with some data bus bits used as the serial port. |
| 9 | D0 | output | Bit 0 of the parallel port data output bus, which is always an output regardless of the SER/PAR state. |
| 10 | D1 | output | Bit 1 of the parallel port data output bus, which is always an output regardless of the SER/PAR state. |
| 11 | D2/DIVSCLK[0] | bidirectional | Bit 2 of the parallel data bus; in serial master read-after-convert mode it is a serial data division clock select input that can slow the internal SDCLK, and is a high-impedance output in other serial modes. |
| 12 | D3/DIVSCLK[1] | bidirectional | Bit 3 of the parallel data bus; in serial master read-after-convert mode it is a serial data division clock select input that can slow the internal SDCLK, and is a high-impedance output in other serial modes. |
| 13 | D4/EXT/INT | bidirectional | Bit 4 of the parallel data bus; in serial mode EXT/INT low selects the internal master serial clock and EXT/INT high selects an external slave clock on SDCLK. |
| 14 | D5/INVSYNC | bidirectional | Bit 5 of the parallel data bus; in serial master mode INVSYNC low makes SYNC active high and INVSYNC high makes SYNC active low. |
| 15 | D6/INVSCLK | bidirectional | Bit 6 of the parallel data bus; in all serial modes INVSCLK low uses the rising edge and INVSCLK high uses the falling edge of SDCLK/SCCLK. |
| 16 | D7/RDC/SDIN | bidirectional | Bit 7 of the parallel data bus; in serial master mode RDC low reads the current result after conversion and RDC high reads the previous result during conversion, while in serial slave mode it is the SDIN daisy-chain data input. |
| 17 | OGND | power_in | Input/output interface digital power ground and ground reference for the digital outputs, ideally at the same potential as AGND and DGND. |
| 18 | OVDD | power_in | Input/output interface digital power, nominally at the host interface supply of 2.5 V, 3 V or 5 V, decoupled with 10 μF and 100 nF capacitors. |
| 19 | DVDD | power_in | Digital power supply, nominally 4.75 V to 5.25 V, decoupled with 10 μF and 100 nF capacitors, and can be supplied from AVDD. |
| 20 | DGND | power_in | Digital power ground and ground reference for the digital outputs, which should be connected to system digital ground ideally at the same potential as AGND and OGND. |
| 21 | D8/SDOUT | output | Bit 8 of the parallel data output bus; in all serial modes it is the serial data output, MSB first, synchronized to SDCLK. |
| 22 | D9/SDCLK | bidirectional | Bit 9 of the parallel data bus; in all serial modes it is the serial data clock input or output depending on the EXT/INT state. |
| 23 | D10/SYNC | bidirectional | Bit 10 of the parallel data output bus; in serial master mode it is the digital output frame synchronization for the internal data clock, with polarity set by INVSYNC. |
| 24 | D11/RDERROR | output | Bit 11 of the parallel data output bus; in serial slave mode it is a read error flag that pulses high if a data read is not completed when the current conversion finishes. |
| 25 | D12/HW/SW | bidirectional | Bit 12 of the parallel data bus; in serial mode HW/SW low selects software configuration via the serial configuration register and HW/SW high selects hardware configuration via dedicated pins. |
| 26 | D13/SCIN | bidirectional | Bit 13 of the parallel data bus; in serial software configuration mode it is the serial configuration data input, MSB first, latched with SCCLK. |
| 27 | D14/SCCLK | bidirectional | Bit 14 of the parallel data bus; in serial software configuration mode it is the serial configuration clock that clocks in SCIN, with the active edge set by INVSCLK. |
| 28 | D15/SCCS | bidirectional | Bit 15 of the parallel data bus; in serial software configuration mode it is the serial configuration chip select that enables the configuration port. |
| 29 | BUSY | output | Busy output that goes high when a conversion starts and stays high until the conversion is complete and data is latched, and whose falling edge can be used as a data-ready clock. |
| 30 | TEN | input | Input range select used with BIPOLAR: low/low gives 0 V to 5 V, low/high gives 0 V to 10 V, high/low gives ±5 V and high/high gives ±10 V (don't-care in serial software configuration mode). |
| 31 | RD | input | Read data input; when CS and RD are both low the parallel or serial output bus is enabled. |
| 32 | CS | input | Chip select input; when CS and RD are both low the parallel or serial output bus is enabled, and CS also gates the external clock in slave serial mode. |
| 33 | RESET | input | Reset input; when high it resets the AD7612 and aborts any current conversion, and its falling edge resets the data outputs to zero and clears the configuration register. |
| 34 | PD | input | Power-down input; when high the ADC is powered down and conversions are inhibited after the current one completes, while the digital interface remains active. |
| 35 | CNVST | input | Conversion start input; a falling edge puts the internal sample-and-hold into hold and initiates a conversion. |
| 36 | BIPOLAR | input | Input range select used with TEN as defined for pin 30 (don't-care in serial software configuration mode). |
| 37 | REF | bidirectional | Reference input/output that produces 5 V when PDREF/PDBUF are low, or accepts an external reference up to AVDD when they are high, and requires at least 22 μF decoupling with or without the internal reference. |
| 38 | REFGND | passive | Reference input analog ground that senses the reference voltage and should be connected to the analog ground plane as a low-impedance return. |
| 39 | IN− | passive | Analog input ground sense that should be connected to the analog ground plane or to a remote sense ground. |
| 40 | VCC | power_in | High voltage positive supply, normally +7 V to +15 V. |
| 41 | VEE | power_in | High voltage negative supply, normally 0 V to −15 V (0 V in unipolar ranges). |
| 42 | AGND | power_in | Analog power ground pin and ground reference for all analog I/O, which should be connected to the analog ground plane and kept at the same potential as AGND, DGND and OGND. |
| 43 | IN+ | passive | Analog input referenced to IN−, with the input voltage range set by the selected input range. |
| 44 | AVDD | power_in | Analog power supply, nominally 4.75 V to 5.25 V, decoupled with 10 μF and 100 nF capacitors. |
| 45 | TEMP | output | Temperature sensor analog output. |
| 46 | REFBUFIN | passive | Reference buffer input that, when PDBUF is low and PDREF is high, produces 5 V on the REF pin from an applied 2.5 V. |
| 47 | PDREF | input | Internal reference power-down input; when low the internal reference is enabled, and when high it is powered down and an external reference must be used. |
| 48 | PDBUF | input | Internal reference buffer power-down input; when low the buffer is enabled and must be low when using the internal reference, and when high the buffer is powered down. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-48(7x7) |
| Category | Data Converters |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage Range, VIN (VIN+ − VIN− = 0 V to 5 V) | VIN | -0.1 | 5.1 | V | VIN+ − VIN− = 0 V to 5 V | 3 | |
| Voltage Range, VIN (VIN+ − VIN− = 0 V to 10 V) | VIN | -0.1 | 10.1 | V | VIN+ − VIN− = 0 V to 10 V | 3 | |
| Voltage Range, VIN (VIN+ − VIN− = ±5 V) | VIN | -5.1 | 5.1 | V | VIN+ − VIN− = ±5 V | 3 | |
| Voltage Range, VIN (VIN+ − VIN− = ±10 V) | VIN | -10.1 | 10.1 | V | VIN+ − VIN− = ±10 V | 3 | |
| Voltage Range, VIN− to AGND | VIN− | -0.1 | 0.1 | V | VIN− to AGND | 3 | |
| Throughput Rate (warp mode) | 750 | kSPS | In warp mode | 3 | |||
| Throughput Rate (normal mode) | 0 | 600 | kSPS | In normal mode | 3 | ||
| Throughput Rate (impulse mode) | 0 | 500 | kSPS | In impulse mode | 3 | ||
| Integral Linearity Error | -1.5 | 0.75 | 1.5 | LSB | 3 | ||
| Differential Linearity Error | -1 | 1.5 | LSB | 3 | |||
| Zero Error (Unipolar or Bipolar) | -35 | 35 | LSB | Unipolar or Bipolar | 3 | ||
| Zero Error Temperature Drift | -1 | 1 | ppm/°C | 3 | |||
| Bipolar Full-Scale Error | -50 | 50 | LSB | 3 | |||
| Unipolar Full-Scale Error | -70 | 70 | LSB | 3 | |||
| Full-Scale Error Temperature Drift | -1 | 1 | ppm/°C | 3 | |||
| Dynamic Range | 92.5 | 93.5 | dB | VIN = 0 V to 5 V, fIN = 2 kHz, −60 dB | 3 | ||
| Signal-to-Noise Ratio | SNR | 92 | 93 | dB | VIN = 0 V to 5 V, 0 V to 10 V, fIN = 2 kHz | 3 | |
| Internal Reference Output Voltage | REF | 4.965 | 5 | 5.035 | V | REF @ 25°C | 3 |
| Internal Reference Temperature Drift | -3 | 3 | ppm/°C | −40°C to +85°C | 3 | ||
| Line Regulation | -15 | 15 | ppm/V | AVDD = 5 V ± 5% | 3 | ||
| SDOUT Valid Delay from External SDCLK Active Edge (t32) | t32 | 2 | 18 | ns | External SDCLK active edge to SDOUT delay; serial interface modes, CL = 10 pF | 6 | |
| Analog Input Supply AVDD (recommended) | AVDD | 4.75 | 5.25 | V | Nominally | 8 | |
| High Voltage Positive Supply VCC (recommended) | VCC | 7 | 15 | V | Normally | 11 | |
| High Voltage Negative Supply VEE (recommended) | VEE | -15 | 0 | V | Normally 0 V to −15 V (0 V in unipolar ranges) | 11 | |
| Digital Output Supply OVDD (recommended) | OVDD | 2.3 | 5.25 | V | Interface with logic working between 2.3 V and 5.25 V | 22 | |
| Operating Temperature Range | TA | -40 | 85 | °C | Operation is specified from −40°C to +85°C | 1 | |
| Ground Voltage Differences AGND, DGND, OGND | -0.3 | 0.3 | V | 7 | |||
| Supply Voltages AVDD, DVDD, OVDD | AVDD, DVDD, OVDD | -0.3 | 7 | V | 7 | ||
| AVDD to DVDD, AVDD to OVDD | -7 | 7 | V | 7 | |||
| DVDD to OVDD | -7 | 7 | V | 7 | |||
| VCC to AGND, DGND | VCC | -0.3 | 16.5 | V | 7 | ||
| VEE to GND | VEE | -16.5 | 0.3 | V | 7 | ||
| PDREF, PDBUF Input Current | -20 | 20 | mA | 7 | |||
| Internal Power Dissipation (LQFP) | PD | 700 | mW | Free air, 48-Lead LQFP | 7 | ||
| Junction Temperature | TJ | 125 | °C | 7 | |||
| Storage Temperature Range | TSTG | -65 | 125 | °C | 7 | ||
| Thermal Resistance Junction-to-Ambient (LQFP) | θJA | 91 | °C/W | Free air, 48-Lead LQFP | 7 | ||
| Thermal Resistance Junction-to-Case (LQFP) | θJC | 30 | °C/W | Free air, 48-Lead LQFP | 7 |
CAD (KiCad official)
- Symbol:
AD7612BSTZ - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
ad7612bstz-etched.step/ad7612bstz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7612bstz.step/ad7612bstz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
be0cbe2f1013fb54, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# AD7612BSTZ
**Analog Devices** · Analog To Digital Converters (ADCs) · LQFP-48(7x7)
AD7612BSTZ from Analog Devices, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AGND | power_in | Analog power ground pin and ground reference for all analog I/O, which should be connected to the analog ground plane and kept at the same potential as AGND, DGND and OGND. |
| 2 | AVDD | power_in | Analog power supply, nominally 4.75 V to 5.25 V, decoupled with 10 μF and 100 nF capacitors. |
| 3 | AGND | power_in | Analog power ground pin and ground reference for all analog I/O, which should be connected to the analog ground plane and kept at the same potential as AGND, DGND and OGND. |
| 4 | BYTESWAP | input | Parallel mode 8/16-bit byte-order select: when high the LSB is output on D[15:8] and the MSB on D[7:0], and when low the LSB is output on D[7:0] and the MSB on D[15:8]. |
| 5 | OB/2C | input | Output coding select: when high the output is straight binary, and when low the MSB is inverted to give twos complement output (this pin is a don't-care in serial software configuration mode). |
| 6 | WARP | input | Conversion mode select used with IMPULSE: WARP/IMPULSE low/low is normal, low/high is impulse, high/low is warp and high/high is normal (don't-care in serial software configuration mode). |
| 7 | IMPULSE | input | Conversion mode select used with WARP as defined for pin 6 (don't-care in serial software configuration mode). |
| 8 | SER/PAR | input | Serial/parallel selection: when low the parallel mode is selected, and when high the serial modes are selected with some data bus bits used as the serial port. |
| 9 | D0 | output | Bit 0 of the parallel port data output bus, which is always an output regardless of the SER/PAR state. |
| 10 | D1 | output | Bit 1 of the parallel port data output bus, which is always an output regardless of the SER/PAR state. |
| 11 | D2/DIVSCLK[0] | bidirectional | Bit 2 of the parallel data bus; in serial master read-after-convert mode it is a serial data division clock select input that can slow the internal SDCLK, and is a high-impedance output in other serial modes. |
| 12 | D3/DIVSCLK[1] | bidirectional | Bit 3 of the parallel data bus; in serial master read-after-convert mode it is a serial data division clock select input that can slow the internal SDCLK, and is a high-impedance output in other serial modes. |
| 13 | D4/EXT/INT | bidirectional | Bit 4 of the parallel data bus; in serial mode EXT/INT low selects the internal master serial clock and EXT/INT high selects an external slave clock on SDCLK. |
| 14 | D5/INVSYNC | bidirectional | Bit 5 of the parallel data bus; in serial master mode INVSYNC low makes SYNC active high and INVSYNC high makes SYNC active low. |
| 15 | D6/INVSCLK | bidirectional | Bit 6 of the parallel data bus; in all serial modes INVSCLK low uses the rising edge and INVSCLK high uses the falling edge of SDCLK/SCCLK. |
| 16 | D7/RDC/SDIN | bidirectional | Bit 7 of the parallel data bus; in serial master mode RDC low reads the current result after conversion and RDC high reads the previous result during conversion, while in serial slave mode it is the SDIN daisy-chain data input. |
| 17 | OGND | power_in | Input/output interface digital power ground and ground reference for the digital outputs, ideally at the same potential as AGND and DGND. |
| 18 | OVDD | power_in | Input/output interface digital power, nominally at the host interface supply of 2.5 V, 3 V or 5 V, decoupled with 10 μF and 100 nF capacitors. |
| 19 | DVDD | power_in | Digital power supply, nominally 4.75 V to 5.25 V, decoupled with 10 μF and 100 nF capacitors, and can be supplied from AVDD. |
| 20 | DGND | power_in | Digital power ground and ground reference for the digital outputs, which should be connected to system digital ground ideally at the same potential as AGND and OGND. |
| 21 | D8/SDOUT | output | Bit 8 of the parallel data output bus; in all serial modes it is the serial data output, MSB first, synchronized to SDCLK. |
| 22 | D9/SDCLK | bidirectional | Bit 9 of the parallel data bus; in all serial modes it is the serial data clock input or output depending on the EXT/INT state. |
| 23 | D10/SYNC | bidirectional | Bit 10 of the parallel data output bus; in serial master mode it is the digital output frame synchronization for the internal data clock, with polarity set by INVSYNC. |
| 24 | D11/RDERROR | output | Bit 11 of the parallel data output bus; in serial slave mode it is a read error flag that pulses high if a data read is not completed when the current conversion finishes. |
| 25 | D12/HW/SW | bidirectional | Bit 12 of the parallel data bus; in serial mode HW/SW low selects software configuration via the serial configuration register and HW/SW high selects hardware configuration via dedicated pins. |
| 26 | D13/SCIN | bidirectional | Bit 13 of the parallel data bus; in serial software configuration mode it is the serial configuration data input, MSB first, latched with SCCLK. |
| 27 | D14/SCCLK | bidirectional | Bit 14 of the parallel data bus; in serial software configuration mode it is the serial configuration clock that clocks in SCIN, with the active edge set by INVSCLK. |
| 28 | D15/SCCS | bidirectional | Bit 15 of the parallel data bus; in serial software configuration mode it is the serial configuration chip select that enables the configuration port. |
| 29 | BUSY | output | Busy output that goes high when a conversion starts and stays high until the conversion is complete and data is latched, and whose falling edge can be used as a data-ready clock. |
| 30 | TEN | input | Input range select used with BIPOLAR: low/low gives 0 V to 5 V, low/high gives 0 V to 10 V, high/low gives ±5 V and high/high gives ±10 V (don't-care in serial software configuration mode). |
| 31 | RD | input | Read data input; when CS and RD are both low the parallel or serial output bus is enabled. |
| 32 | CS | input | Chip select input; when CS and RD are both low the parallel or serial output bus is enabled, and CS also gates the external clock in slave serial mode. |
| 33 | RESET | input | Reset input; when high it resets the AD7612 and aborts any current conversion, and its falling edge resets the data outputs to zero and clears the configuration register. |
| 34 | PD | input | Power-down input; when high the ADC is powered down and conversions are inhibited after the current one completes, while the digital interface remains active. |
| 35 | CNVST | input | Conversion start input; a falling edge puts the internal sample-and-hold into hold and initiates a conversion. |
| 36 | BIPOLAR | input | Input range select used with TEN as defined for pin 30 (don't-care in serial software configuration mode). |
| 37 | REF | bidirectional | Reference input/output that produces 5 V when PDREF/PDBUF are low, or accepts an external reference up to AVDD when they are high, and requires at least 22 μF decoupling with or without the internal reference. |
| 38 | REFGND | passive | Reference input analog ground that senses the reference voltage and should be connected to the analog ground plane as a low-impedance return. |
| 39 | IN− | passive | Analog input ground sense that should be connected to the analog ground plane or to a remote sense ground. |
| 40 | VCC | power_in | High voltage positive supply, normally +7 V to +15 V. |
| 41 | VEE | power_in | High voltage negative supply, normally 0 V to −15 V (0 V in unipolar ranges). |
| 42 | AGND | power_in | Analog power ground pin and ground reference for all analog I/O, which should be connected to the analog ground plane and kept at the same potential as AGND, DGND and OGND. |
| 43 | IN+ | passive | Analog input referenced to IN−, with the input voltage range set by the selected input range. |
| 44 | AVDD | power_in | Analog power supply, nominally 4.75 V to 5.25 V, decoupled with 10 μF and 100 nF capacitors. |
| 45 | TEMP | output | Temperature sensor analog output. |
| 46 | REFBUFIN | passive | Reference buffer input that, when PDBUF is low and PDREF is high, produces 5 V on the REF pin from an applied 2.5 V. |
| 47 | PDREF | input | Internal reference power-down input; when low the internal reference is enabled, and when high it is powered down and an external reference must be used. |
| 48 | PDBUF | input | Internal reference buffer power-down input; when low the buffer is enabled and must be low when using the internal reference, and when high the buffer is powered down. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LQFP-48(7x7) |
| Category | Data Converters |
| Pins | 48 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage Range, VIN (VIN+ − VIN− = 0 V to 5 V) | VIN | -0.1 | | 5.1 | V | VIN+ − VIN− = 0 V to 5 V | 3 |
| Voltage Range, VIN (VIN+ − VIN− = 0 V to 10 V) | VIN | -0.1 | | 10.1 | V | VIN+ − VIN− = 0 V to 10 V | 3 |
| Voltage Range, VIN (VIN+ − VIN− = ±5 V) | VIN | -5.1 | | 5.1 | V | VIN+ − VIN− = ±5 V | 3 |
| Voltage Range, VIN (VIN+ − VIN− = ±10 V) | VIN | -10.1 | | 10.1 | V | VIN+ − VIN− = ±10 V | 3 |
| Voltage Range, VIN− to AGND | VIN− | -0.1 | | 0.1 | V | VIN− to AGND | 3 |
| Throughput Rate (warp mode) | | | | 750 | kSPS | In warp mode | 3 |
| Throughput Rate (normal mode) | | 0 | | 600 | kSPS | In normal mode | 3 |
| Throughput Rate (impulse mode) | | 0 | | 500 | kSPS | In impulse mode | 3 |
| Integral Linearity Error | | -1.5 | 0.75 | 1.5 | LSB | | 3 |
| Differential Linearity Error | | -1 | | 1.5 | LSB | | 3 |
| Zero Error (Unipolar or Bipolar) | | -35 | | 35 | LSB | Unipolar or Bipolar | 3 |
| Zero Error Temperature Drift | | -1 | | 1 | ppm/°C | | 3 |
| Bipolar Full-Scale Error | | -50 | | 50 | LSB | | 3 |
| Unipolar Full-Scale Error | | -70 | | 70 | LSB | | 3 |
| Full-Scale Error Temperature Drift | | -1 | | 1 | ppm/°C | | 3 |
| Dynamic Range | | 92.5 | 93.5 | | dB | VIN = 0 V to 5 V, fIN = 2 kHz, −60 dB | 3 |
| Signal-to-Noise Ratio | SNR | 92 | 93 | | dB | VIN = 0 V to 5 V, 0 V to 10 V, fIN = 2 kHz | 3 |
| Internal Reference Output Voltage | REF | 4.965 | 5 | 5.035 | V | REF @ 25°C | 3 |
| Internal Reference Temperature Drift | | -3 | | 3 | ppm/°C | −40°C to +85°C | 3 |
| Line Regulation | | -15 | | 15 | ppm/V | AVDD = 5 V ± 5% | 3 |
| SDOUT Valid Delay from External SDCLK Active Edge (t32) | t32 | 2 | | 18 | ns | External SDCLK active edge to SDOUT delay; serial interface modes, CL = 10 pF | 6 |
| Analog Input Supply AVDD (recommended) | AVDD | 4.75 | | 5.25 | V | Nominally | 8 |
| High Voltage Positive Supply VCC (recommended) | VCC | 7 | | 15 | V | Normally | 11 |
| High Voltage Negative Supply VEE (recommended) | VEE | -15 | | 0 | V | Normally 0 V to −15 V (0 V in unipolar ranges) | 11 |
| Digital Output Supply OVDD (recommended) | OVDD | 2.3 | | 5.25 | V | Interface with logic working between 2.3 V and 5.25 V | 22 |
| Operating Temperature Range | TA | -40 | | 85 | °C | Operation is specified from −40°C to +85°C | 1 |
| Ground Voltage Differences AGND, DGND, OGND | | -0.3 | | 0.3 | V | | 7 |
| Supply Voltages AVDD, DVDD, OVDD | AVDD, DVDD, OVDD | -0.3 | | 7 | V | | 7 |
| AVDD to DVDD, AVDD to OVDD | | -7 | | 7 | V | | 7 |
| DVDD to OVDD | | -7 | | 7 | V | | 7 |
| VCC to AGND, DGND | VCC | -0.3 | | 16.5 | V | | 7 |
| VEE to GND | VEE | -16.5 | | 0.3 | V | | 7 |
| PDREF, PDBUF Input Current | | -20 | | 20 | mA | | 7 |
| Internal Power Dissipation (LQFP) | PD | | | 700 | mW | Free air, 48-Lead LQFP | 7 |
| Junction Temperature | TJ | | | 125 | °C | | 7 |
| Storage Temperature Range | TSTG | -65 | | 125 | °C | | 7 |
| Thermal Resistance Junction-to-Ambient (LQFP) | θJA | | 91 | | °C/W | Free air, 48-Lead LQFP | 7 |
| Thermal Resistance Junction-to-Case (LQFP) | θJC | | 30 | | °C/W | Free air, 48-Lead LQFP | 7 |
## CAD (KiCad official)
- Symbol: `AD7612BSTZ`
- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`
- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files: `ad7612bstz-etched.step` / `ad7612bstz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ad7612bstz.step` / `ad7612bstz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/AD7612.pdf) (32 pp, sha256 `be0cbe2f1013fb54`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ad7612bstz-datasheet.pdf)