main
Ray
Publish 0.1.0
8fc6b5d
AD7293BCPZ-RL
Analog Devices · ADC/DAC - Specialized · LFCSP-56(8x8)
AD7293BCPZ-RL from Analog Devices, in a LFCSP-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FACTORY TEST | passive | Factory test pin that must be left unconnected or connected to DGND. |
| 2 | GPIO4/ALERT1 | bidirectional | General-purpose I/O 4, defaulting to ALERT1 out-of-range indicator; open-drain output that requires a pull-up resistor to VDRIVE, with register-selectable polarity. |
| 3 | GPIO5/SLEEP0 | bidirectional | General-purpose I/O 5, defaulting to SLEEP0, the DAC power-down digital input (register-selectable polarity) that can trigger DAC clamping on any combination of DAC channels. |
| 4 | GPIO6/SLEEP1 | bidirectional | General-purpose I/O 6, defaulting to SLEEP1, the DAC power-down digital input (register-selectable polarity) that can trigger DAC clamping on any combination of DAC channels. |
| 5 | RESET | input | Reset input; taking this pin low performs a hardware reset. |
| 6 | GPIO7/LDAC | bidirectional | General-purpose I/O 7, defaulting to LDAC; when active it updates the DAC output registers, with register-selectable polarity. |
| 7 | SCLK | input | SPI serial clock input for the serial port interface. |
| 8 | CS | input | Active-low chip select input that frames the serial data input. |
| 9 | DIN | input | SPI serial data input; data is clocked into the device on the rising edge of SCLK. |
| 10 | DOUT | tri_state | SPI serial data output; data is clocked out on the falling edge of SCLK and the pin is high impedance when not outputting data. |
| 11 | DGND | power_in | Digital ground, the ground reference for all digital circuitry; connect to the system ground plane together with AGND. |
| 12 | VDRIVE | power_in | Drive voltage reference level of the SPI bus, from 1.7 V to 5.5 V. |
| 13 | DVDD | power_in | Digital supply voltage from 4.5 V to 5.5 V. |
| 14 | DACVDD-UNI | power_in | Positive supply pin for the unipolar DAC output amplifiers on UNI-VOUT0 to UNI-VOUT3. |
| 15 | UNI-VOUT0 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 16 | UNI-VOUT1 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 17 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 18 | UNI-VOUT2 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 19 | UNI-VOUT3 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 20 | VREFIN | input | Reference input to the device; connect to an external reference voltage or tie to VREFOUT. |
| 21 | VREFOUT | output | 2.5 V reference output; connect to VREFIN for internal reference mode, with an optional 10 nF capacitor to AGND recommended for noise filtering. |
| 22 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 23 | BI-VOUT0 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 24 | BI-VOUT1 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 25 | AVSS | power_in | DAC negative supply pin for the BI-VOUT0 to BI-VOUT3 DAC output amplifiers. |
| 26 | DACVDD-BI | power_in | Analog supply pin for BI-VOUT0 to BI-VOUT3; connect to the same potential as AVDD. |
| 27 | BI-VOUT2 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 28 | BI-VOUT3 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 29 | VCLAMP1 | input | Power-on reset and clamp voltage for BI-VOUT2 and BI-VOUT3. |
| 30 | VCLAMP0 | input | Power-on reset and clamp voltage for BI-VOUT0 and BI-VOUT1. |
| 31 | RS3- | input | Negative connection for external shunt resistor 3. |
| 32 | RS3+ | input | Positive connection for external shunt resistor 3. |
| 33 | RS2- | input | Negative connection for external shunt resistor 2. |
| 34 | RS2+ | input | Positive connection for external shunt resistor 2. |
| 35 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 36 | RS1- | input | Negative connection for external shunt resistor 1. |
| 37 | RS1+ | input | Positive connection for external shunt resistor 1. |
| 38 | RS0- | input | Negative connection for external shunt resistor 0. |
| 39 | RS0+ | input | Positive connection for external shunt resistor 0. |
| 40 | PA_ON | output | Drives an external PMOS switch controlling PA drain current; the PA is on when the output is low, and the voltage is set by PAVDD and limited to AVSS + 60 V. |
| 41 | PAVDD | power_in | Power supply for the PA_ON control signal, limited to 4 V to AVSS + 60 V. |
| 42 | REFADC | passive | Internal ADC reference at half VREFIN (1.25 V); a 4.7 µF compensation capacitor to AGND is recommended and a minimum of 220 nF X7R/C0G is required. |
| 43 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 44 | AVDD | power_in | Supply voltage for all analog circuitry, 4.5 V to 5.5 V; connect to the same potential as DACVDD-BI. |
| 45 | VIN3 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 46 | VIN2 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 47 | VIN1 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 48 | VIN0 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 49 | D1- | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 50 | D1+ | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 51 | D0- | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 52 | D0+ | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 53 | GPIO3/ALERT0 | bidirectional | General-purpose I/O 3, defaulting to GPIO; ALERT0 out-of-range indicator is open-drain in both modes and requires a pull-up resistor to VDRIVE. |
| 54 | GPIO2/BUSY | bidirectional | General-purpose I/O 2, defaulting to GPIO; BUSY goes active during a conversion, is open-drain in both modes, and requires a pull-up resistor to VDRIVE. |
| 55 | GPIO1/CONVST | bidirectional | General-purpose I/O 1, defaulting to an open-drain GPIO; CONVST is the external ADC convert start input and needs a pull-up to VDRIVE in GPIO mode or when unused. |
| 56 | GPIO0/IS BLANK | bidirectional | General-purpose I/O 0, which is an open-drain output in GPIO mode; its IS BLANK function is not described in the supplied pages. |
| 57 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LFCSP-56(8x8) |
| Category | ADC/DAC/Data Conversion |
| Pins | 57 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Integral Nonlinearity (INL) | -1 | 0.5 | 1 | LSB | 6 | ||
| Differential Nonlinearity (DNL) | -0.99 | 0.5 | 0.99 | LSB | No missing codes | 6 | |
| Gain Error (ADC) | -6.5 | 3 | 6.5 | LSB | Differential Mode | 6 | |
| Zero Code Error (ADC) | -2.5 | 0.4 | 2.5 | LSB | Single-Ended Mode | 6 | |
| Zero Code Error (ADC) | -2 | 0.5 | 2 | LSB | Differential Mode | 6 | |
| Single-Ended Input Range | 0 | 1.25 | V | 0 V to REFADC mode | 6 | ||
| Single-Ended Input Range | 0 | 2.5 | V | 0 V to 2 × REFADC mode | 6 | ||
| Single-Ended Input Range | 0 | 5 | V | 0 V to 4 × REFADC mode | 6 | ||
| Internal BI-VOUTx Monitoring Full-Scale Input Range | -5 | 5 | V | 6 | |||
| Internal RSx+ Monitoring Full-Scale Input Range | 0 | 62.5 | V | 6 | |||
| Internal Reference Output Voltage | 2.495 | 2.5 | 2.505 | V | At TA = 25°C only | 6 | |
| Internal Reference Temperature Coefficient | -30 | 10 | 30 | ppm/°C | 6 | ||
| External Reference Input Voltage Range | 2.48 | 2.5 | 2.52 | V | 6 | ||
| Integral Nonlinearity (INL) DAC | -1.7 | 1 | 1.7 | LSB | Bipolar | 7 | |
| Integral Nonlinearity (INL) DAC | -3 | 3 | LSB | Unipolar | 7 | ||
| Differential Nonlinearity (DNL) DAC | -0.99 | 0.3 | 1 | LSB | Guaranteed monotonic | 7 | |
| Bipolar Open-Loop DAC Range | 0 | 5 | V | BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 | 7 | ||
| Bipolar Open-Loop DAC Range | -4 | 1 | V | BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 | 7 | ||
| Bipolar Open-Loop DAC Range | -5 | 0 | V | BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 | 7 | ||
| Unipolar DAC Range | 0 | 5 | V | UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 | 7 | ||
| Unipolar DAC Range | 2.5 | 7.5 | V | UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 | 7 | ||
| Unipolar DAC Range | 5 | 10 | V | UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 | 7 | ||
| DAC Load Current | -10 | 10 | mA | Source and/or sink within 300 mV of supply | 8 | ||
| Clamp Output Current | -10 | 10 | mA | Source and/or sink within 300 mV of supply | 8 | ||
| Output Voltage Settling Time | 1.2 | 1.3 | µs | ¼ to ¾ change within ±1 LSB, measured from the last SCLK rising edge, CL = 200 pF | 8 | ||
| Internal Temperature Sensor Accuracy | -3 | 1.25 | 3 | °C | Internal temperature sensor, TA = −40°C to +125°C | 8 | |
| External Temperature Sensor Operating Range | -55 | 150 | °C | Limited by external transistor | 8 | ||
| External Temperature Sensor Accuracy | -3 | 1.1 | 3 | °C | TA = −40°C to +105°C | 8 | |
| Common-Mode Input Voltage Range (RSx+) | 4 | 60 | V | AVSS = 0 V | 9 | ||
| Common-Mode Input Voltage Range (RSx+) | 4 | 55 | V | AVSS = −5 V | 9 | ||
| Differential Input Voltage Range | -200 | 200 | mV | Gain = 6.25, for gain settings, see Table 44 | 9 | ||
| Current Sensor Gain Error | -0.7 | 0.1 | 0.7 | % | 9 | ||
| DC Common-Mode Rejection | 100 | 140 | dB | 9 | |||
| Sense Resistor Voltage Range | 0 | 200 | mV | 9 | |||
| AVDD Alarm Threshold | 3.2 | 3.6 | 3.9 | V | 9 | ||
| AVSS Alarm Threshold | -3.8 | -4.1 | -4.4 | V | 9 | ||
| Positive Analog Supply Voltage | AVDD | 4.5 | 5.5 | V | 10 | ||
| Negative Analog Supply Voltage | AVSS | -5.5 | V | 10 | |||
| Logic Power Supply Voltage | VDRIVE | 1.7 | 5.5 | V | Supports 1.8 V, 3 V, and 5 V interfaces | 10 | |
| Unipolar DAC Supply Voltage | DACVDD-UNI | 4.5 | 12.5 | V | 10 | ||
| Bipolar DAC Supply Voltage | DACVDD-BI | 4.5 | 5.5 | V | 10 | ||
| PA_ON Power Supply Voltage | PAVDD | 4.5 | V | 10 | |||
| RSx+ Voltage | VRSx+ | 4 | V | 10 | |||
| AVDD Supply Current | AIDD | 9 | 12.5 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 | |
| AVSS Supply Current | AISS | -4.4 | -5.4 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 | |
| VDRIVE Supply Current | IDRIVE | 1 | 2.1 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 | |
| DACVDD-UNI Supply Current | DACIDD-UNI | 2.1 | 3 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 | |
| DACVDD-BI Supply Current | DACIDD-BI | 5 | 8.2 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 | |
| PAVDD Supply Current | PAIDD | 81 | 100 | µA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 | |
| DACVDD-UNI Supply to AGND | -0.3 | 15 | V | 13 | |||
| Analog Pins REFADC, D1−, D1+, D0−, D0+ to AGND | -0.3 | 2 | V | 13 | |||
| Open-Drain Pins to DGND | -0.3 | 7 | V | 13 | |||
| 5 V Supply Pins VDRIVE, DACVDD-BI, AVDD to AGND | -0.3 | 7 | V | 13 | |||
| −5 V Supply Pin AVSS to AGND | -7 | 0.3 | V | 13 | |||
| Operating Temperature Range | -40 | 125 | °C | 13 | |||
| Storage Temperature Range | -65 | 125 | °C | 13 | |||
| Maximum Junction Temperature | 150 | °C | 13 | ||||
| Thermal Resistance, Junction-to-Ambient (56-Lead LFCSP) | θJA | 27 | °C/W | 13 | |||
| Thermal Resistance, Junction-to-Case (56-Lead LFCSP) | θJC | 0.5 | °C/W | 13 |
CAD (KiCad official)
- Symbol:
AD7293BCPZ-RL - Footprint:
Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm - 3D model: LFCSP-56(8x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ad7293bcpz-etched.step/ad7293bcpz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7293bcpz.step/ad7293bcpz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (79 pp, sha256
7818e03bd6c9bffc, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# AD7293BCPZ-RL
**Analog Devices** · ADC/DAC - Specialized · LFCSP-56(8x8)
AD7293BCPZ-RL from Analog Devices, in a LFCSP-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FACTORY TEST | passive | Factory test pin that must be left unconnected or connected to DGND. |
| 2 | GPIO4/ALERT1 | bidirectional | General-purpose I/O 4, defaulting to ALERT1 out-of-range indicator; open-drain output that requires a pull-up resistor to VDRIVE, with register-selectable polarity. |
| 3 | GPIO5/SLEEP0 | bidirectional | General-purpose I/O 5, defaulting to SLEEP0, the DAC power-down digital input (register-selectable polarity) that can trigger DAC clamping on any combination of DAC channels. |
| 4 | GPIO6/SLEEP1 | bidirectional | General-purpose I/O 6, defaulting to SLEEP1, the DAC power-down digital input (register-selectable polarity) that can trigger DAC clamping on any combination of DAC channels. |
| 5 | RESET | input | Reset input; taking this pin low performs a hardware reset. |
| 6 | GPIO7/LDAC | bidirectional | General-purpose I/O 7, defaulting to LDAC; when active it updates the DAC output registers, with register-selectable polarity. |
| 7 | SCLK | input | SPI serial clock input for the serial port interface. |
| 8 | CS | input | Active-low chip select input that frames the serial data input. |
| 9 | DIN | input | SPI serial data input; data is clocked into the device on the rising edge of SCLK. |
| 10 | DOUT | tri_state | SPI serial data output; data is clocked out on the falling edge of SCLK and the pin is high impedance when not outputting data. |
| 11 | DGND | power_in | Digital ground, the ground reference for all digital circuitry; connect to the system ground plane together with AGND. |
| 12 | VDRIVE | power_in | Drive voltage reference level of the SPI bus, from 1.7 V to 5.5 V. |
| 13 | DVDD | power_in | Digital supply voltage from 4.5 V to 5.5 V. |
| 14 | DACVDD-UNI | power_in | Positive supply pin for the unipolar DAC output amplifiers on UNI-VOUT0 to UNI-VOUT3. |
| 15 | UNI-VOUT0 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 16 | UNI-VOUT1 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 17 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 18 | UNI-VOUT2 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 19 | UNI-VOUT3 | output | Unipolar DAC output whose clamp and power-on reset voltage is 0 V. |
| 20 | VREFIN | input | Reference input to the device; connect to an external reference voltage or tie to VREFOUT. |
| 21 | VREFOUT | output | 2.5 V reference output; connect to VREFIN for internal reference mode, with an optional 10 nF capacitor to AGND recommended for noise filtering. |
| 22 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 23 | BI-VOUT0 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 24 | BI-VOUT1 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 25 | AVSS | power_in | DAC negative supply pin for the BI-VOUT0 to BI-VOUT3 DAC output amplifiers. |
| 26 | DACVDD-BI | power_in | Analog supply pin for BI-VOUT0 to BI-VOUT3; connect to the same potential as AVDD. |
| 27 | BI-VOUT2 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 28 | BI-VOUT3 | output | Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx. |
| 29 | VCLAMP1 | input | Power-on reset and clamp voltage for BI-VOUT2 and BI-VOUT3. |
| 30 | VCLAMP0 | input | Power-on reset and clamp voltage for BI-VOUT0 and BI-VOUT1. |
| 31 | RS3- | input | Negative connection for external shunt resistor 3. |
| 32 | RS3+ | input | Positive connection for external shunt resistor 3. |
| 33 | RS2- | input | Negative connection for external shunt resistor 2. |
| 34 | RS2+ | input | Positive connection for external shunt resistor 2. |
| 35 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 36 | RS1- | input | Negative connection for external shunt resistor 1. |
| 37 | RS1+ | input | Positive connection for external shunt resistor 1. |
| 38 | RS0- | input | Negative connection for external shunt resistor 0. |
| 39 | RS0+ | input | Positive connection for external shunt resistor 0. |
| 40 | PA_ON | output | Drives an external PMOS switch controlling PA drain current; the PA is on when the output is low, and the voltage is set by PAVDD and limited to AVSS + 60 V. |
| 41 | PAVDD | power_in | Power supply for the PA_ON control signal, limited to 4 V to AVSS + 60 V. |
| 42 | REFADC | passive | Internal ADC reference at half VREFIN (1.25 V); a 4.7 µF compensation capacitor to AGND is recommended and a minimum of 220 nF X7R/C0G is required. |
| 43 | AGND | power_in | Analog ground; connect together with DGND to the system ground plane. |
| 44 | AVDD | power_in | Supply voltage for all analog circuitry, 4.5 V to 5.5 V; connect to the same potential as DACVDD-BI. |
| 45 | VIN3 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 46 | VIN2 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 47 | VIN1 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 48 | VIN0 | input | ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating. |
| 49 | D1- | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 50 | D1+ | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 51 | D0- | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 52 | D0+ | input | Temperature sensor analog input for the external sensing transistor; tie to AGND if unused. |
| 53 | GPIO3/ALERT0 | bidirectional | General-purpose I/O 3, defaulting to GPIO; ALERT0 out-of-range indicator is open-drain in both modes and requires a pull-up resistor to VDRIVE. |
| 54 | GPIO2/BUSY | bidirectional | General-purpose I/O 2, defaulting to GPIO; BUSY goes active during a conversion, is open-drain in both modes, and requires a pull-up resistor to VDRIVE. |
| 55 | GPIO1/CONVST | bidirectional | General-purpose I/O 1, defaulting to an open-drain GPIO; CONVST is the external ADC convert start input and needs a pull-up to VDRIVE in GPIO mode or when unused. |
| 56 | GPIO0/IS BLANK | bidirectional | General-purpose I/O 0, which is an open-drain output in GPIO mode; its IS BLANK function is not described in the supplied pages. |
| 57 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LFCSP-56(8x8) |
| Category | ADC/DAC/Data Conversion |
| Pins | 57 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Integral Nonlinearity (INL) | | -1 | 0.5 | 1 | LSB | | 6 |
| Differential Nonlinearity (DNL) | | -0.99 | 0.5 | 0.99 | LSB | No missing codes | 6 |
| Gain Error (ADC) | | -6.5 | 3 | 6.5 | LSB | Differential Mode | 6 |
| Zero Code Error (ADC) | | -2.5 | 0.4 | 2.5 | LSB | Single-Ended Mode | 6 |
| Zero Code Error (ADC) | | -2 | 0.5 | 2 | LSB | Differential Mode | 6 |
| Single-Ended Input Range | | 0 | | 1.25 | V | 0 V to REFADC mode | 6 |
| Single-Ended Input Range | | 0 | | 2.5 | V | 0 V to 2 × REFADC mode | 6 |
| Single-Ended Input Range | | 0 | | 5 | V | 0 V to 4 × REFADC mode | 6 |
| Internal BI-VOUTx Monitoring Full-Scale Input Range | | -5 | | 5 | V | | 6 |
| Internal RSx+ Monitoring Full-Scale Input Range | | 0 | | 62.5 | V | | 6 |
| Internal Reference Output Voltage | | 2.495 | 2.5 | 2.505 | V | At TA = 25°C only | 6 |
| Internal Reference Temperature Coefficient | | -30 | 10 | 30 | ppm/°C | | 6 |
| External Reference Input Voltage Range | | 2.48 | 2.5 | 2.52 | V | | 6 |
| Integral Nonlinearity (INL) DAC | | -1.7 | 1 | 1.7 | LSB | Bipolar | 7 |
| Integral Nonlinearity (INL) DAC | | -3 | | 3 | LSB | Unipolar | 7 |
| Differential Nonlinearity (DNL) DAC | | -0.99 | 0.3 | 1 | LSB | Guaranteed monotonic | 7 |
| Bipolar Open-Loop DAC Range | | 0 | | 5 | V | BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 | 7 |
| Bipolar Open-Loop DAC Range | | -4 | | 1 | V | BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 | 7 |
| Bipolar Open-Loop DAC Range | | -5 | | 0 | V | BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 | 7 |
| Unipolar DAC Range | | 0 | | 5 | V | UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 | 7 |
| Unipolar DAC Range | | 2.5 | | 7.5 | V | UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 | 7 |
| Unipolar DAC Range | | 5 | | 10 | V | UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 | 7 |
| DAC Load Current | | -10 | | 10 | mA | Source and/or sink within 300 mV of supply | 8 |
| Clamp Output Current | | -10 | | 10 | mA | Source and/or sink within 300 mV of supply | 8 |
| Output Voltage Settling Time | | | 1.2 | 1.3 | µs | ¼ to ¾ change within ±1 LSB, measured from the last SCLK rising edge, CL = 200 pF | 8 |
| Internal Temperature Sensor Accuracy | | -3 | 1.25 | 3 | °C | Internal temperature sensor, TA = −40°C to +125°C | 8 |
| External Temperature Sensor Operating Range | | -55 | | 150 | °C | Limited by external transistor | 8 |
| External Temperature Sensor Accuracy | | -3 | 1.1 | 3 | °C | TA = −40°C to +105°C | 8 |
| Common-Mode Input Voltage Range (RSx+) | | 4 | | 60 | V | AVSS = 0 V | 9 |
| Common-Mode Input Voltage Range (RSx+) | | 4 | | 55 | V | AVSS = −5 V | 9 |
| Differential Input Voltage Range | | -200 | | 200 | mV | Gain = 6.25, for gain settings, see Table 44 | 9 |
| Current Sensor Gain Error | | -0.7 | 0.1 | 0.7 | % | | 9 |
| DC Common-Mode Rejection | | 100 | 140 | | dB | | 9 |
| Sense Resistor Voltage Range | | 0 | | 200 | mV | | 9 |
| AVDD Alarm Threshold | | 3.2 | 3.6 | 3.9 | V | | 9 |
| AVSS Alarm Threshold | | -3.8 | -4.1 | -4.4 | V | | 9 |
| Positive Analog Supply Voltage | AVDD | 4.5 | | 5.5 | V | | 10 |
| Negative Analog Supply Voltage | AVSS | -5.5 | | | V | | 10 |
| Logic Power Supply Voltage | VDRIVE | 1.7 | | 5.5 | V | Supports 1.8 V, 3 V, and 5 V interfaces | 10 |
| Unipolar DAC Supply Voltage | DACVDD-UNI | 4.5 | | 12.5 | V | | 10 |
| Bipolar DAC Supply Voltage | DACVDD-BI | 4.5 | | 5.5 | V | | 10 |
| PA_ON Power Supply Voltage | PAVDD | 4.5 | | | V | | 10 |
| RSx+ Voltage | VRSx+ | 4 | | | V | | 10 |
| AVDD Supply Current | AIDD | | 9 | 12.5 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 |
| AVSS Supply Current | AISS | | -4.4 | -5.4 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 |
| VDRIVE Supply Current | IDRIVE | | 1 | 2.1 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 |
| DACVDD-UNI Supply Current | DACIDD-UNI | | 2.1 | 3 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 |
| DACVDD-BI Supply Current | DACIDD-BI | | 5 | 8.2 | mA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 |
| PAVDD Supply Current | PAIDD | | 81 | 100 | µA | All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied | 10 |
| DACVDD-UNI Supply to AGND | | -0.3 | | 15 | V | | 13 |
| Analog Pins REFADC, D1−, D1+, D0−, D0+ to AGND | | -0.3 | | 2 | V | | 13 |
| Open-Drain Pins to DGND | | -0.3 | | 7 | V | | 13 |
| 5 V Supply Pins VDRIVE, DACVDD-BI, AVDD to AGND | | -0.3 | | 7 | V | | 13 |
| −5 V Supply Pin AVSS to AGND | | -7 | | 0.3 | V | | 13 |
| Operating Temperature Range | | -40 | | 125 | °C | | 13 |
| Storage Temperature Range | | -65 | | 125 | °C | | 13 |
| Maximum Junction Temperature | | | | 150 | °C | | 13 |
| Thermal Resistance, Junction-to-Ambient (56-Lead LFCSP) | θJA | | 27 | | °C/W | | 13 |
| Thermal Resistance, Junction-to-Case (56-Lead LFCSP) | θJC | | 0.5 | | °C/W | | 13 |
## CAD (KiCad official)
- Symbol: `AD7293BCPZ-RL`
- Footprint: `Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm`
- 3D model: LFCSP-56(8x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `ad7293bcpz-etched.step` / `ad7293bcpz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ad7293bcpz.step` / `ad7293bcpz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/AD7293.pdf) (79 pp, sha256 `7818e03bd6c9bffc`, retrieved 2026-11-12, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ad7293bcpz-datasheet.pdf)