Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

AD7293BCPZ-RL

Analog Devices · ADC/DAC - Specialized · LFCSP-56(8x8)

AD7293BCPZ-RL from Analog Devices, in a LFCSP-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FACTORY TEST passive Factory test pin that must be left unconnected or connected to DGND.
2 GPIO4/ALERT1 bidirectional General-purpose I/O 4, defaulting to ALERT1 out-of-range indicator; open-drain output that requires a pull-up resistor to VDRIVE, with register-selectable polarity.
3 GPIO5/SLEEP0 bidirectional General-purpose I/O 5, defaulting to SLEEP0, the DAC power-down digital input (register-selectable polarity) that can trigger DAC clamping on any combination of DAC channels.
4 GPIO6/SLEEP1 bidirectional General-purpose I/O 6, defaulting to SLEEP1, the DAC power-down digital input (register-selectable polarity) that can trigger DAC clamping on any combination of DAC channels.
5 RESET input Reset input; taking this pin low performs a hardware reset.
6 GPIO7/LDAC bidirectional General-purpose I/O 7, defaulting to LDAC; when active it updates the DAC output registers, with register-selectable polarity.
7 SCLK input SPI serial clock input for the serial port interface.
8 CS input Active-low chip select input that frames the serial data input.
9 DIN input SPI serial data input; data is clocked into the device on the rising edge of SCLK.
10 DOUT tri_state SPI serial data output; data is clocked out on the falling edge of SCLK and the pin is high impedance when not outputting data.
11 DGND power_in Digital ground, the ground reference for all digital circuitry; connect to the system ground plane together with AGND.
12 VDRIVE power_in Drive voltage reference level of the SPI bus, from 1.7 V to 5.5 V.
13 DVDD power_in Digital supply voltage from 4.5 V to 5.5 V.
14 DACVDD-UNI power_in Positive supply pin for the unipolar DAC output amplifiers on UNI-VOUT0 to UNI-VOUT3.
15 UNI-VOUT0 output Unipolar DAC output whose clamp and power-on reset voltage is 0 V.
16 UNI-VOUT1 output Unipolar DAC output whose clamp and power-on reset voltage is 0 V.
17 AGND power_in Analog ground; connect together with DGND to the system ground plane.
18 UNI-VOUT2 output Unipolar DAC output whose clamp and power-on reset voltage is 0 V.
19 UNI-VOUT3 output Unipolar DAC output whose clamp and power-on reset voltage is 0 V.
20 VREFIN input Reference input to the device; connect to an external reference voltage or tie to VREFOUT.
21 VREFOUT output 2.5 V reference output; connect to VREFIN for internal reference mode, with an optional 10 nF capacitor to AGND recommended for noise filtering.
22 AGND power_in Analog ground; connect together with DGND to the system ground plane.
23 BI-VOUT0 output Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx.
24 BI-VOUT1 output Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx.
25 AVSS power_in DAC negative supply pin for the BI-VOUT0 to BI-VOUT3 DAC output amplifiers.
26 DACVDD-BI power_in Analog supply pin for BI-VOUT0 to BI-VOUT3; connect to the same potential as AVDD.
27 BI-VOUT2 output Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx.
28 BI-VOUT3 output Bipolar DAC output in open-loop mode and integrator output in closed-loop mode; clamp and power-on reset voltage is set by VCLAMPx.
29 VCLAMP1 input Power-on reset and clamp voltage for BI-VOUT2 and BI-VOUT3.
30 VCLAMP0 input Power-on reset and clamp voltage for BI-VOUT0 and BI-VOUT1.
31 RS3- input Negative connection for external shunt resistor 3.
32 RS3+ input Positive connection for external shunt resistor 3.
33 RS2- input Negative connection for external shunt resistor 2.
34 RS2+ input Positive connection for external shunt resistor 2.
35 AGND power_in Analog ground; connect together with DGND to the system ground plane.
36 RS1- input Negative connection for external shunt resistor 1.
37 RS1+ input Positive connection for external shunt resistor 1.
38 RS0- input Negative connection for external shunt resistor 0.
39 RS0+ input Positive connection for external shunt resistor 0.
40 PA_ON output Drives an external PMOS switch controlling PA drain current; the PA is on when the output is low, and the voltage is set by PAVDD and limited to AVSS + 60 V.
41 PAVDD power_in Power supply for the PA_ON control signal, limited to 4 V to AVSS + 60 V.
42 REFADC passive Internal ADC reference at half VREFIN (1.25 V); a 4.7 µF compensation capacitor to AGND is recommended and a minimum of 220 nF X7R/C0G is required.
43 AGND power_in Analog ground; connect together with DGND to the system ground plane.
44 AVDD power_in Supply voltage for all analog circuitry, 4.5 V to 5.5 V; connect to the same potential as DACVDD-BI.
45 VIN3 input ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating.
46 VIN2 input ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating.
47 VIN1 input ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating.
48 VIN0 input ADC analog input with register-selectable range of 0 V to 1.25 V, 0 V to 2.5 V, or 0 V to 5 V; unused inputs must not be left floating.
49 D1- input Temperature sensor analog input for the external sensing transistor; tie to AGND if unused.
50 D1+ input Temperature sensor analog input for the external sensing transistor; tie to AGND if unused.
51 D0- input Temperature sensor analog input for the external sensing transistor; tie to AGND if unused.
52 D0+ input Temperature sensor analog input for the external sensing transistor; tie to AGND if unused.
53 GPIO3/ALERT0 bidirectional General-purpose I/O 3, defaulting to GPIO; ALERT0 out-of-range indicator is open-drain in both modes and requires a pull-up resistor to VDRIVE.
54 GPIO2/BUSY bidirectional General-purpose I/O 2, defaulting to GPIO; BUSY goes active during a conversion, is open-drain in both modes, and requires a pull-up resistor to VDRIVE.
55 GPIO1/CONVST bidirectional General-purpose I/O 1, defaulting to an open-drain GPIO; CONVST is the external ADC convert start input and needs a pull-up to VDRIVE in GPIO mode or when unused.
56 GPIO0/IS BLANK bidirectional General-purpose I/O 0, which is an open-drain output in GPIO mode; its IS BLANK function is not described in the supplied pages.
57 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Analog Devices
Package LFCSP-56(8x8)
Category ADC/DAC/Data Conversion
Pins 57

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Integral Nonlinearity (INL) -1 0.5 1 LSB 6
Differential Nonlinearity (DNL) -0.99 0.5 0.99 LSB No missing codes 6
Gain Error (ADC) -6.5 3 6.5 LSB Differential Mode 6
Zero Code Error (ADC) -2.5 0.4 2.5 LSB Single-Ended Mode 6
Zero Code Error (ADC) -2 0.5 2 LSB Differential Mode 6
Single-Ended Input Range 0 1.25 V 0 V to REFADC mode 6
Single-Ended Input Range 0 2.5 V 0 V to 2 × REFADC mode 6
Single-Ended Input Range 0 5 V 0 V to 4 × REFADC mode 6
Internal BI-VOUTx Monitoring Full-Scale Input Range -5 5 V 6
Internal RSx+ Monitoring Full-Scale Input Range 0 62.5 V 6
Internal Reference Output Voltage 2.495 2.5 2.505 V At TA = 25°C only 6
Internal Reference Temperature Coefficient -30 10 30 ppm/°C 6
External Reference Input Voltage Range 2.48 2.5 2.52 V 6
Integral Nonlinearity (INL) DAC -1.7 1 1.7 LSB Bipolar 7
Integral Nonlinearity (INL) DAC -3 3 LSB Unipolar 7
Differential Nonlinearity (DNL) DAC -0.99 0.3 1 LSB Guaranteed monotonic 7
Bipolar Open-Loop DAC Range 0 5 V BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 7
Bipolar Open-Loop DAC Range -4 1 V BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 7
Bipolar Open-Loop DAC Range -5 0 V BI-VOUT0, BI-VOUT1, BI-VOUT2, and BI-VOUT3 7
Unipolar DAC Range 0 5 V UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 7
Unipolar DAC Range 2.5 7.5 V UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 7
Unipolar DAC Range 5 10 V UNI-VOUT0, UNI-VOUT1, UNI-VOUT2, and UNI-VOUT3 7
DAC Load Current -10 10 mA Source and/or sink within 300 mV of supply 8
Clamp Output Current -10 10 mA Source and/or sink within 300 mV of supply 8
Output Voltage Settling Time 1.2 1.3 µs ¼ to ¾ change within ±1 LSB, measured from the last SCLK rising edge, CL = 200 pF 8
Internal Temperature Sensor Accuracy -3 1.25 3 °C Internal temperature sensor, TA = −40°C to +125°C 8
External Temperature Sensor Operating Range -55 150 °C Limited by external transistor 8
External Temperature Sensor Accuracy -3 1.1 3 °C TA = −40°C to +105°C 8
Common-Mode Input Voltage Range (RSx+) 4 60 V AVSS = 0 V 9
Common-Mode Input Voltage Range (RSx+) 4 55 V AVSS = −5 V 9
Differential Input Voltage Range -200 200 mV Gain = 6.25, for gain settings, see Table 44 9
Current Sensor Gain Error -0.7 0.1 0.7 % 9
DC Common-Mode Rejection 100 140 dB 9
Sense Resistor Voltage Range 0 200 mV 9
AVDD Alarm Threshold 3.2 3.6 3.9 V 9
AVSS Alarm Threshold -3.8 -4.1 -4.4 V 9
Positive Analog Supply Voltage AVDD 4.5 5.5 V 10
Negative Analog Supply Voltage AVSS -5.5 V 10
Logic Power Supply Voltage VDRIVE 1.7 5.5 V Supports 1.8 V, 3 V, and 5 V interfaces 10
Unipolar DAC Supply Voltage DACVDD-UNI 4.5 12.5 V 10
Bipolar DAC Supply Voltage DACVDD-BI 4.5 5.5 V 10
PA_ON Power Supply Voltage PAVDD 4.5 V 10
RSx+ Voltage VRSx+ 4 V 10
AVDD Supply Current AIDD 9 12.5 mA All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied 10
AVSS Supply Current AISS -4.4 -5.4 mA All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied 10
VDRIVE Supply Current IDRIVE 1 2.1 mA All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied 10
DACVDD-UNI Supply Current DACIDD-UNI 2.1 3 mA All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied 10
DACVDD-BI Supply Current DACIDD-BI 5 8.2 mA All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied 10
PAVDD Supply Current PAIDD 81 100 µA All power supplies set to maximum voltage; ADC on and converting; DACs enabled with no load applied 10
DACVDD-UNI Supply to AGND -0.3 15 V 13
Analog Pins REFADC, D1−, D1+, D0−, D0+ to AGND -0.3 2 V 13
Open-Drain Pins to DGND -0.3 7 V 13
5 V Supply Pins VDRIVE, DACVDD-BI, AVDD to AGND -0.3 7 V 13
−5 V Supply Pin AVSS to AGND -7 0.3 V 13
Operating Temperature Range -40 125 °C 13
Storage Temperature Range -65 125 °C 13
Maximum Junction Temperature 150 °C 13
Thermal Resistance, Junction-to-Ambient (56-Lead LFCSP) θJA 27 °C/W 13
Thermal Resistance, Junction-to-Case (56-Lead LFCSP) θJC 0.5 °C/W 13

CAD (KiCad official)

  • Symbol: AD7293BCPZ-RL
  • Footprint: Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm
  • 3D model: LFCSP-56(8x8), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ad7293bcpz-etched.step / ad7293bcpz-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ad7293bcpz.step / ad7293bcpz.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (79 pp, sha256 7818e03bd6c9bffc, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF