Generated by kicad-footprint-generator · KiCad file format 20260206
AD7173-8BCPZ
Analog Devices · Analog To Digital Converters (ADCs) · LFCSP-40(6x6)
AD7173-8BCPZ from Analog Devices, in a LFCSP-40(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AIN16 | passive | Analog input 16, selectable through the cross point multiplexer. |
| 2 | AIN0/REF2− | passive | Analog input 0, selectable through the cross point multiplexer, and negative terminal of external Reference 2, which can span from AVSS to AVDD1 − 1 V. |
| 3 | AIN1/REF2+ | passive | Analog input 1, selectable through the cross point multiplexer, and positive terminal of external Reference 2, which can span from AVDD1 to AVSS + 1 V. |
| 4 | AIN2 | passive | Analog input 2, selectable through the cross point multiplexer. |
| 5 | AIN3 | passive | Analog input 3, selectable through the cross point multiplexer. |
| 6 | REFOUT | output | Buffered output of the internal reference, 2.5 V with respect to AVSS. |
| 7 | REGCAPA | output | Analog LDO regulator output that must be decoupled to AVSS using a 1 µF capacitor. |
| 8 | AVSS | power_in | Negative analog supply ranging from 0 V to −2.75 V, nominally set to 0 V. |
| 9 | AVDD1 | power_in | Analog supply voltage 1, ranging from 3.0 V minimum to 5.5 V maximum with respect to AVSS. |
| 10 | AVDD2 | power_in | Analog supply voltage 2, ranging from 2 V to AVDD1 with respect to AVSS. |
| 11 | PDSW | output | Power-down switch connected to AVSS, controlled by the PDSW bit in the GPIOCON register. |
| 12 | XTAL1 | passive | Input 1 for the crystal. |
| 13 | XTAL2/CLKIO | bidirectional | Input 2 for the crystal (XTAL2) or clock input/output (CLKIO), configured by the CLOCKSEL bits in the ADCMODE register. |
| 14 | DOUT/RDY | output | Serial data output (DOUT) and data ready output (RDY); tristated when CS is high, and goes low to indicate conversion completion when CS is low and no register is being read. |
| 15 | DIN | input | Serial data input to the ADC input shift register, clocked in on the rising edge of SCLK. |
| 16 | SCLK | input | Serial clock input for data transfers to and from the ADC, with a Schmitt trigger input for opto-isolated applications. |
| 17 | CS | input | Active-low chip select input used to select the ADC; it can be hardwired low for 3-wire operation. |
| 18 | ERROR | bidirectional | Configurable as an active-low error input, an active-low open-drain error output, or a general-purpose output referenced between IOVDD and DGND. |
| 19 | SYNC | input | Synchronization input that allows the digital filters and analog modulators of multiple AD7173-8 devices to be synchronized. |
| 20 | IOVDD | power_in | Digital I/O supply voltage ranging from 2 V to 5 V, independent of AVDD1 and AVDD2; if AVSS is set to −2.5 V, IOVDD must not exceed 3.6 V. |
| 21 | DGND | power_in | Digital ground. |
| 22 | REGCAPD | output | Digital LDO regulator output, for decoupling purposes only, to be decoupled to DGND using a 1 µF capacitor. |
| 23 | GPIO0 | bidirectional | General-purpose input/output with logic levels referenced to the AVDD1 and AVSS supplies. |
| 24 | GPIO1 | bidirectional | General-purpose input/output with logic levels referenced to the AVDD1 and AVSS supplies. |
| 25 | GPO2 | output | General-purpose output with logic levels referenced to the AVDD1 and AVSS supplies. |
| 26 | AIN4 | passive | Analog input 4, selectable through the cross point multiplexer. |
| 27 | AIN5 | passive | Analog input 5, selectable through the cross point multiplexer. |
| 28 | AIN6 | passive | Analog input 6, selectable through the cross point multiplexer. |
| 29 | AIN7 | passive | Analog input 7, selectable through the cross point multiplexer. |
| 30 | AIN8 | passive | Analog input 8, selectable through the cross point multiplexer. |
| 31 | AIN9 | passive | Analog input 9, selectable through the cross point multiplexer. |
| 32 | AIN10 | passive | Analog input 10, selectable through the cross point multiplexer. |
| 33 | AIN11 | passive | Analog input 11, selectable through the cross point multiplexer. |
| 34 | AIN12 | passive | Analog input 12, selectable through the cross point multiplexer. |
| 35 | AIN13 | passive | Analog input 13, selectable through the cross point multiplexer. |
| 36 | AIN14 | passive | Analog input 14, selectable through the cross point multiplexer. |
| 37 | AIN15 | passive | Analog input 15, selectable through the cross point multiplexer. |
| 38 | GPO3 | output | General-purpose output with logic levels referenced to the AVDD1 and AVSS supplies. |
| 39 | REF− | passive | Reference 1 negative input terminal, which can span from AVSS to AVDD1 − 1 V. |
| 40 | REF+ | passive | Reference 1 positive input terminal, which can span from AVDD1 to AVSS + 1 V. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | LFCSP-40(6x6) |
| Category | ADC/DAC/Data Conversion |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Data Rate (ODR) | ODR | 1.25 | 31250 | SPS | 4 | ||
| Integral Nonlinearity (INL), 2.5 V reference | INL | -7.5 | 3 | 7.5 | ppm/FSR | 2.5 V reference | 4 |
| Integral Nonlinearity (INL), 5 V reference | INL | -5 | 5 | ppm/FSR | 5 V reference | 4 | |
| Offset Error | -40 | 40 | µV | Internal short | 4 | ||
| Offset Drift | -350 | 350 | nV/°C | Internal short | 4 | ||
| Gain Error | -50 | 10 | 50 | ppm/FSR | 25°C, AVDD1 = 5 V | 4 | |
| Gain Drift vs. Temperature | -1 | 0.5 | 1 | ppm/FSR/°C | 4 | ||
| Initial Accuracy (REFOUT) | -0.1 | 0.1 | % of V | TA = 25°C | 4 | ||
| Internal Reference Temperature Coefficient, 0°C to +105°C | 3.5 | 81 | ppm/°C | 0°C to +105°C | 4 | ||
| Internal Reference Temperature Coefficient, −40°C to +105°C | 3.5 | 101 | ppm/°C | −40°C to +105°C | 4 | ||
| Reference Load Current | IL | -10 | 10 | mA | 4 | ||
| External Reference Input Voltage (REF+ − REF−) | 1 | 2.5 | V | Reference input = (REF+) − (REF−) | 5 | ||
| Average Reference Input Current | -9 | 9 | µA/V | Buffers disabled | 5 | ||
| Temperature Sensor Accuracy | -2 | 2 | °C | After user calibration at 25°C | 5 | ||
| Burnout Current Source/Sink | -10 | 10 | µA | Analog input buffers must be enabled | 5 | ||
| Power Supply Rejection | 90 | dB | AVDD1 and AVDD2, VIN = 1 V | 4 | |||
| Common-Mode Rejection, DC | 95 | dB | VIN = 0.1 V, at DC | 4 | |||
| Normal Mode Rejection, internal clock | 71 | 90 | dB | Internal clock, 20 SPS ODR (post filter) | 4 | ||
| Input Current, buffers disabled | -6 | 6 | µA/V | Buffers disabled | 4 | ||
| GPIO Output High Voltage, referenced to AVSS | VOH | 4 | V | AVDD1 − AVSS = 5 V; ISOURCE = 200 µA | 5 | ||
| GPIO Output Low Voltage, referenced to AVSS | VOL | 0.4 | V | AVDD1 − AVSS = 5 V; ISINK = 800 µA | 5 | ||
| GPIO Input High Voltage, referenced to AVSS | VIH | 3 | V | AVDD1 − AVSS = 5 V | 5 | ||
| GPIO Input Low Voltage, referenced to AVSS | VIL | 0.7 | V | AVDD1 − AVSS = 5 V | 5 | ||
| GPIO Output High Voltage, referenced to AVSS | VOH | 2.7 | V | AVDD1 − AVSS = 3.3 V; ISOURCE = 200 µA | 5 | ||
| GPIO Output Low Voltage, referenced to AVSS | VOL | 0.27 | V | AVDD1 − AVSS = 3.3 V; ISINK = 800 µA | 5 | ||
| GPIO Input High Voltage, referenced to AVSS | VIH | 2 | V | AVDD1 − AVSS = 3.3 V | 5 | ||
| GPIO Input Low Voltage, referenced to AVSS | VIL | 0.45 | V | AVDD1 − AVSS = 3.3 V | 5 | ||
| Absolute Max: AVDD1, AVDD2 to AVSS | -0.3 | 6.5 | V | 9 | |||
| Absolute Max: AVDD1 to DGND | -0.3 | 6.5 | V | 9 | |||
| Absolute Max: IOVDD to DGND | -0.3 | 6.5 | V | 9 | |||
| Absolute Max: IOVDD to AVSS | -0.3 | 7.5 | V | 9 | |||
| Absolute Max: AVSS to DGND | -3.25 | 0.3 | V | 9 | |||
| Absolute Max: Analog Input Voltage to AVSS | -0.3 | V | Upper limit printed as AVDD1 + 0.3 V | 9 | |||
| Absolute Max: Reference Input Voltage to AVSS | -0.3 | V | Upper limit printed as AVDD1 + 0.3 V | 9 | |||
| Absolute Max: Digital Input Voltage to DGND | -0.3 | V | Upper limit printed as IOVDD + 0.3 V | 9 | |||
| Operating Temperature Range | TA | -40 | 105 | °C | 9 | ||
| Recommended: Analog Supply Voltage 1 (AVDD1) | AVDD1 | 3 | 5.5 | V | AVSS = DGND = 0 V | 4 | |
| Recommended: Analog Supply Voltage 2 (AVDD2) | AVDD2 | 2 | 5.5 | V | AVSS = DGND = 0 V | 4 | |
| Recommended: Digital I/O Supply (IOVDD) | IOVDD | 2 | 5.5 | V | AVSS = DGND = 0 V | 4 | |
| Recommended: Negative Analog Supply (AVSS) | AVSS | -2.75 | 0 | V | Nominally 0 V | 10 | |
| SCLK High Pulse Width | t3 | 25 | ns | SCLK high pulse width | 8 | ||
| SCLK Low Pulse Width | t4 | 25 | ns | SCLK low pulse width | 8 | ||
| CS Falling Edge to DOUT/RDY Active Time | t1 | 0 | ns | CS falling edge to DOUT/RDY active time | 8 | ||
| CS Falling Edge to DOUT/RDY Active Time | t1 | 15 | ns | IOVDD = 4.5 V to 5.5 V | 8 | ||
| CS Falling Edge to DOUT/RDY Active Time | t1 | 40 | ns | IOVDD = 2 V to 3.6 V | 8 | ||
| SCLK Active Edge to Data Valid Delay | t2 | 0 | ns | SCLK active edge to data valid delay | 8 | ||
| SCLK Active Edge to Data Valid Delay | t2 | 12 | ns | IOVDD = 4.5 V to 5.5 V | 8 | ||
| SCLK Active Edge to Data Valid Delay | t2 | 25 | ns | IOVDD = 2 V to 3.6 V | 8 | ||
| Bus Relinquish Time After CS Inactive Edge | t5 | 2.5 | ns | Bus relinquish time after CS inactive edge | 8 | ||
| Bus Relinquish Time After CS Inactive Edge | t5 | 20 | ns | Bus relinquish time after CS inactive edge | 8 | ||
| SCLK Inactive Edge to CS Inactive Edge | t6 | 0 | ns | SCLK inactive edge to CS inactive edge | 8 | ||
| SCLK Inactive Edge to DOUT/RDY High/Low | t7 | 10 | ns | SCLK inactive edge to DOUT/RDY high/low | 8 | ||
| CS Falling Edge to SCLK Active Edge Setup Time | t8 | 0 | ns | CS falling edge to SCLK active edge setup time | 8 | ||
| Data Valid to SCLK Edge Setup Time | t9 | 8 | ns | Data valid to SCLK edge setup time | 8 | ||
| Data Valid to SCLK Edge Hold Time | t10 | 8 | ns | Data valid to SCLK edge hold time | 8 | ||
| CS Rising Edge to SCLK Edge Hold Time | t11 | 5 | ns | CS rising edge to SCLK edge hold time | 8 | ||
| Thermal Resistance θJA, 40-lead 6 mm × 6 mm LFCSP, 1-layer JEDEC board | θJA | 114 | °C/W | 1-layer JEDEC board | 9 | ||
| Thermal Resistance θJA, 40-lead 6 mm × 6 mm LFCSP, 4-layer JEDEC board | θJA | 54 | °C/W | 4-layer JEDEC board | 9 | ||
| Thermal Resistance θJA, 40-lead 6 mm × 6 mm LFCSP, 4-layer JEDEC board with 16 thermal vias | θJA | 34 | °C/W | 4-layer JEDEC board with 16 thermal vias | 9 |
CAD (KiCad official)
- Symbol:
AD7173-8BCPZ - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: LFCSP-40(6x6), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ad7173-8bcpz-etched.step/ad7173-8bcpz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad7173-8bcpz.step/ad7173-8bcpz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (64 pp, sha256
0587d78edc631435, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).