main
Ray
Publish 0.1.0
2f3fc54
A3959SLPTR-T
Allegro MicroSystems, LLC · Brushed DC Motor Drivers · TSSOP-28-EP
A3959SLPTR-T from Allegro MicroSystems, LLC, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CP | passive | Reservoir capacitor terminal; a 0.22 µF ceramic capacitor connects CP to VBB to act as the reservoir for the high-side DMOS devices. |
| 2 | CP1 | passive | Charge-pump capacitor terminal; a 0.22 µF ceramic capacitor is connected between CP1 and CP2 for pumping. |
| 3 | CP2 | passive | Charge-pump capacitor terminal; a 0.22 µF ceramic capacitor is connected between CP1 and CP2 for pumping. |
| 4 | NC | unconnected | No (internal) connection. |
| 5 | PHASE | input | Logic input for direction control; PHASE 0 gives OUTA low and OUTB high, PHASE 1 gives OUTA high and OUTB low. |
| 6 | ROSC | passive | Oscillator resistor to VDD; typical 51 kΩ sets 4 MHz, with an allowable range of 20 kΩ to 100 kΩ (shorted to ground if not pulled up to VDD). |
| 7 | GROUND | power_in | Ground; for the LP package, terminals 7, 8 and 28 should be connected together at the exposed pad beneath the device. |
| 8 | GROUND | power_in | Ground; for the LP package, terminals 7, 8 and 28 should be connected together at the exposed pad beneath the device. |
| 9 | VDD | power_in | Logic supply, the low-voltage supply typically 5 V. |
| 10 | ENABLE | input | Logic input for enable control; ENABLE high turns on the selected sink-source pair and ENABLE low chops the outputs. |
| 11 | NC | unconnected | No (internal) connection. |
| 12 | PFD2 | input | Logic-level input for fast-decay selection; together with PFD1 it sets slow, mixed or fast current decay. |
| 13 | BLANK | input | Logic-level input for blanking control; BLANK 0 gives 6/fosc blanking time and BLANK 1 gives 12/fosc. |
| 14 | PFD1 | input | Logic-level input for fast-decay selection; together with PFD2 it sets slow, mixed or fast current decay. |
| 15 | REF | input | VREF load current reference input voltage; the trip current is ITRIP = VREF/10RS. |
| 16 | EXT MODE | input | Logic input for PWM mode control; EXT MODE low selects fast decay and EXT MODE high selects slow decay during external PWM. |
| 17 | NO CONNECT | unconnected | No (internal) connection. |
| 18 | OUTA | output | One of two DMOS bridge outputs to the motor; repetitive output current rating ±3.0 A, peak ±6.0 A for less than 3 µs. |
| 19 | NC | unconnected | No (internal) connection. |
| 20 | NC | unconnected | No (internal) connection. |
| 21 | SENSE | input | Sense resistor input; continuous sense voltage rating 0.5 V and 2.5 V for tw < 3 µs, with the sense resistor requiring an independent ground return. |
| 22 | NC | unconnected | No (internal) connection. |
| 23 | VBB | power_in | Load supply, the high-current motor supply rated 9.5 V to 50 V. |
| 24 | OUTB | output | One of two DMOS bridge outputs to the motor; repetitive output current rating ±3.0 A, peak ±6.0 A for less than 3 µs. |
| 25 | NO CONNECT | unconnected | No (internal) connection. |
| 26 | SLEEP | input | Logic-level input for sleep operation; logic low puts the device into sleep mode, and if sleep is unused a 5 kΩ pull-up to VDD is required. |
| 27 | VREG | passive | Regulator decoupling capacitor terminal; a 0.22 µF capacitor to ground is recommended. |
| 28 | GROUND | power_in | Ground; for the LP package, terminals 7, 8 and 28 should be connected together at the exposed pad beneath the device. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | TSSOP-28-EP |
| Category | Motor Driver ICs |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Load Supply Voltage (absolute maximum) | VBB | 50 | V | 2 | |||
| Logic Supply Voltage (absolute maximum) | VDD | 7 | V | 2 | |||
| Input Voltage (absolute maximum) | VIN | -0.3 | V | Continuous; upper limit VDD + 0.3 V | 2 | ||
| Input Voltage (absolute maximum) | VIN | -1 | V | tw < 30 ns; upper limit VDD + 1.0 V | 2 | ||
| Sense Voltage (absolute maximum) | VS | 0.5 | V | Continuous | 2 | ||
| Sense Voltage (absolute maximum) | VS | 2.5 | V | tw < 3 µs | 2 | ||
| Output Current (absolute maximum) | IOUT | -3 | 3 | A | Repetitive | 2 | |
| Output Current (absolute maximum) | IOUT | -6 | 6 | A | Peak, < 3 µs | 2 | |
| Operating Ambient Temperature (absolute maximum) | TA | -20 | 85 | °C | Range S | 2 | |
| Maximum Junction Temperature | TJ(max) | 150 | °C | 2 | |||
| Storage Temperature | Tstg | -55 | 150 | °C | 2 | ||
| Load Supply Voltage Range | VBB | 9.5 | 50 | V | Operating | 4 | |
| Load Supply Voltage Range | VBB | 0 | 50 | V | During sleep mode | 4 | |
| Logic Supply Voltage Range | VDD | 4.5 | 5 | 5.5 | V | Operating | 4 |
| Reference Input Voltage Range | VREF | 0 | V | Operating; upper limit VDD | 4 | ||
| Output Leakage Current | IDSS | 20 | µA | VOUT = VBB | 4 | ||
| Output Leakage Current | IDSS | -20 | µA | VOUT = 0 V | 4 | ||
| Output On Resistance | rDS(on) | 270 | 300 | mΩ | Source driver, IOUT = -3 A | 4 | |
| Crossover Delay | 300 | 600 | 1000 | ns | 4 | ||
| Body Diode Forward Voltage | VF | 1.6 | V | Source diode, IF = -3 A | 4 | ||
| Load Supply Current | IBB | 4 | 7 | mA | fPWM < 50 kHz | 4 | |
| Load Supply Current | IBB | 2 | 5 | mA | Charge pump on, outputs disabled | 4 | |
| Load Supply Current | IBB | 20 | µA | Sleep mode | 4 | ||
| Logic Input Voltage | VIN(1) | 2 | V | 4 | |||
| Logic Input Voltage | VIN(0) | 0.8 | V | 4 | |||
| Logic Input Current (all inputs except ENABLE) | IIN(1) | 20 | µA | VIN = 2.0 V | 4 | ||
| Logic Input Current (all inputs except ENABLE) | IIN(0) | -20 | µA | VIN = 0.8 V | 4 | ||
| Logic Supply Current | IDD | 6 | 10 | mA | fPWM < 50 kHz | 4 | |
| Logic Supply Current | IDD | 2 | mA | Sleep mode | 4 | ||
| ENABLE Input Current | IIN(1) | 40 | 100 | µA | VIN = 2.0 V | 4 | |
| ENABLE Input Current | IIN(0) | 16 | 40 | µA | VIN = 0.8 V | 4 | |
| Internal OSC Frequency | fOSC | 3.25 | 4.25 | 5.25 | MHz | ROSC shorted to GROUND | 4 |
| Internal OSC Frequency | fOSC | 3.65 | 4.25 | 4.85 | MHz | ROSC = 51 kΩ | 4 |
| Reference Input Current | IREF | -1 | 1 | µA | VREF = VDD | 4 | |
| Comparator Input Offset Voltage | VIO | -5 | 5 | mV | VREF = 0 V | 4 | |
| Gm Error | EGm | -4 | 4 | % | VREF = VDD | 5 | |
| Gm Error | EGm | -14 | 14 | % | VREF = 0.5 V | 5 | |
| Propagation Delay Time | tpd | 600 | 750 | 1200 | ns | 0.5 Ein to 0.9 Eout; PWM change to source on | 5 |
| Propagation Delay Time | tpd | 50 | 150 | 350 | ns | 0.5 Ein to 0.9 Eout; PWM change to source off | 5 |
| Propagation Delay Time | tpd | 50 | 100 | 150 | ns | 0.5 Ein to 0.9 Eout; PWM change to sink off | 5 |
| UVLO Enable Threshold | VUVLO | 3.9 | 4.2 | 4.45 | V | Increasing VDD | 5 |
| UVLO Hysteresis | ΔVUVLO | 0.05 | 0.1 | V | 5 | ||
| Package Thermal Resistance, Junction to Ambient (LP, 1-layer PCB) | RθJA | 100 | °C/W | LP package; 1-layer PCB, minimal exposed copper area | 3 | ||
| Package Thermal Resistance, Junction to Ambient (LP, 2-layer PCB) | RθJA | 40 | °C/W | LP package; 2-layer PCB, 1-in.² 2-oz copper exposed area | 3 | ||
| Package Thermal Resistance, Junction to Ambient (LP, 4-layer PCB) | RθJA | 28 | °C/W | LP package; 4-layer PCB, based on JEDEC standard | 3 | ||
| Package Thermal Resistance, Junction to Pad | RθJP | 2 | °C/W | LP package | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | is lead (Pb) free, with 100% matte tin leadframes. 29319.37L, Rev. 14 | 1 |
CAD (KiCad official)
- Symbol:
A3959SLPTR-T - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
a3959slptr-t-etched.step/a3959slptr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);a3959slptr-t.step/a3959slptr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Allegro MicroSystems, LLC datasheet (12 pp, sha256
a424976468934aa8, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# A3959SLPTR-T
**Allegro MicroSystems, LLC** · Brushed DC Motor Drivers · TSSOP-28-EP
A3959SLPTR-T from Allegro MicroSystems, LLC, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CP | passive | Reservoir capacitor terminal; a 0.22 µF ceramic capacitor connects CP to VBB to act as the reservoir for the high-side DMOS devices. |
| 2 | CP1 | passive | Charge-pump capacitor terminal; a 0.22 µF ceramic capacitor is connected between CP1 and CP2 for pumping. |
| 3 | CP2 | passive | Charge-pump capacitor terminal; a 0.22 µF ceramic capacitor is connected between CP1 and CP2 for pumping. |
| 4 | NC | unconnected | No (internal) connection. |
| 5 | PHASE | input | Logic input for direction control; PHASE 0 gives OUTA low and OUTB high, PHASE 1 gives OUTA high and OUTB low. |
| 6 | ROSC | passive | Oscillator resistor to VDD; typical 51 kΩ sets 4 MHz, with an allowable range of 20 kΩ to 100 kΩ (shorted to ground if not pulled up to VDD). |
| 7 | GROUND | power_in | Ground; for the LP package, terminals 7, 8 and 28 should be connected together at the exposed pad beneath the device. |
| 8 | GROUND | power_in | Ground; for the LP package, terminals 7, 8 and 28 should be connected together at the exposed pad beneath the device. |
| 9 | VDD | power_in | Logic supply, the low-voltage supply typically 5 V. |
| 10 | ENABLE | input | Logic input for enable control; ENABLE high turns on the selected sink-source pair and ENABLE low chops the outputs. |
| 11 | NC | unconnected | No (internal) connection. |
| 12 | PFD2 | input | Logic-level input for fast-decay selection; together with PFD1 it sets slow, mixed or fast current decay. |
| 13 | BLANK | input | Logic-level input for blanking control; BLANK 0 gives 6/fosc blanking time and BLANK 1 gives 12/fosc. |
| 14 | PFD1 | input | Logic-level input for fast-decay selection; together with PFD2 it sets slow, mixed or fast current decay. |
| 15 | REF | input | VREF load current reference input voltage; the trip current is ITRIP = VREF/10RS. |
| 16 | EXT MODE | input | Logic input for PWM mode control; EXT MODE low selects fast decay and EXT MODE high selects slow decay during external PWM. |
| 17 | NO CONNECT | unconnected | No (internal) connection. |
| 18 | OUTA | output | One of two DMOS bridge outputs to the motor; repetitive output current rating ±3.0 A, peak ±6.0 A for less than 3 µs. |
| 19 | NC | unconnected | No (internal) connection. |
| 20 | NC | unconnected | No (internal) connection. |
| 21 | SENSE | input | Sense resistor input; continuous sense voltage rating 0.5 V and 2.5 V for tw < 3 µs, with the sense resistor requiring an independent ground return. |
| 22 | NC | unconnected | No (internal) connection. |
| 23 | VBB | power_in | Load supply, the high-current motor supply rated 9.5 V to 50 V. |
| 24 | OUTB | output | One of two DMOS bridge outputs to the motor; repetitive output current rating ±3.0 A, peak ±6.0 A for less than 3 µs. |
| 25 | NO CONNECT | unconnected | No (internal) connection. |
| 26 | SLEEP | input | Logic-level input for sleep operation; logic low puts the device into sleep mode, and if sleep is unused a 5 kΩ pull-up to VDD is required. |
| 27 | VREG | passive | Regulator decoupling capacitor terminal; a 0.22 µF capacitor to ground is recommended. |
| 28 | GROUND | power_in | Ground; for the LP package, terminals 7, 8 and 28 should be connected together at the exposed pad beneath the device. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Allegro MicroSystems, LLC |
| Package | TSSOP-28-EP |
| Category | Motor Driver ICs |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Load Supply Voltage (absolute maximum) | VBB | | | 50 | V | | 2 |
| Logic Supply Voltage (absolute maximum) | VDD | | | 7 | V | | 2 |
| Input Voltage (absolute maximum) | VIN | -0.3 | | | V | Continuous; upper limit VDD + 0.3 V | 2 |
| Input Voltage (absolute maximum) | VIN | -1 | | | V | tw < 30 ns; upper limit VDD + 1.0 V | 2 |
| Sense Voltage (absolute maximum) | VS | | | 0.5 | V | Continuous | 2 |
| Sense Voltage (absolute maximum) | VS | | | 2.5 | V | tw < 3 µs | 2 |
| Output Current (absolute maximum) | IOUT | -3 | | 3 | A | Repetitive | 2 |
| Output Current (absolute maximum) | IOUT | -6 | | 6 | A | Peak, < 3 µs | 2 |
| Operating Ambient Temperature (absolute maximum) | TA | -20 | | 85 | °C | Range S | 2 |
| Maximum Junction Temperature | TJ(max) | | | 150 | °C | | 2 |
| Storage Temperature | Tstg | -55 | | 150 | °C | | 2 |
| Load Supply Voltage Range | VBB | 9.5 | | 50 | V | Operating | 4 |
| Load Supply Voltage Range | VBB | 0 | | 50 | V | During sleep mode | 4 |
| Logic Supply Voltage Range | VDD | 4.5 | 5 | 5.5 | V | Operating | 4 |
| Reference Input Voltage Range | VREF | 0 | | | V | Operating; upper limit VDD | 4 |
| Output Leakage Current | IDSS | | | 20 | µA | VOUT = VBB | 4 |
| Output Leakage Current | IDSS | | | -20 | µA | VOUT = 0 V | 4 |
| Output On Resistance | rDS(on) | | 270 | 300 | mΩ | Source driver, IOUT = -3 A | 4 |
| Crossover Delay | | 300 | 600 | 1000 | ns | | 4 |
| Body Diode Forward Voltage | VF | | | 1.6 | V | Source diode, IF = -3 A | 4 |
| Load Supply Current | IBB | | 4 | 7 | mA | fPWM < 50 kHz | 4 |
| Load Supply Current | IBB | | 2 | 5 | mA | Charge pump on, outputs disabled | 4 |
| Load Supply Current | IBB | | | 20 | µA | Sleep mode | 4 |
| Logic Input Voltage | VIN(1) | 2 | | | V | | 4 |
| Logic Input Voltage | VIN(0) | | | 0.8 | V | | 4 |
| Logic Input Current (all inputs except ENABLE) | IIN(1) | | | 20 | µA | VIN = 2.0 V | 4 |
| Logic Input Current (all inputs except ENABLE) | IIN(0) | | | -20 | µA | VIN = 0.8 V | 4 |
| Logic Supply Current | IDD | | 6 | 10 | mA | fPWM < 50 kHz | 4 |
| Logic Supply Current | IDD | | | 2 | mA | Sleep mode | 4 |
| ENABLE Input Current | IIN(1) | | 40 | 100 | µA | VIN = 2.0 V | 4 |
| ENABLE Input Current | IIN(0) | | 16 | 40 | µA | VIN = 0.8 V | 4 |
| Internal OSC Frequency | fOSC | 3.25 | 4.25 | 5.25 | MHz | ROSC shorted to GROUND | 4 |
| Internal OSC Frequency | fOSC | 3.65 | 4.25 | 4.85 | MHz | ROSC = 51 kΩ | 4 |
| Reference Input Current | IREF | -1 | | 1 | µA | VREF = VDD | 4 |
| Comparator Input Offset Voltage | VIO | -5 | | 5 | mV | VREF = 0 V | 4 |
| Gm Error | EGm | -4 | | 4 | % | VREF = VDD | 5 |
| Gm Error | EGm | -14 | | 14 | % | VREF = 0.5 V | 5 |
| Propagation Delay Time | tpd | 600 | 750 | 1200 | ns | 0.5 Ein to 0.9 Eout; PWM change to source on | 5 |
| Propagation Delay Time | tpd | 50 | 150 | 350 | ns | 0.5 Ein to 0.9 Eout; PWM change to source off | 5 |
| Propagation Delay Time | tpd | 50 | 100 | 150 | ns | 0.5 Ein to 0.9 Eout; PWM change to sink off | 5 |
| UVLO Enable Threshold | VUVLO | 3.9 | 4.2 | 4.45 | V | Increasing VDD | 5 |
| UVLO Hysteresis | ΔVUVLO | 0.05 | 0.1 | | V | | 5 |
| Package Thermal Resistance, Junction to Ambient (LP, 1-layer PCB) | RθJA | | 100 | | °C/W | LP package; 1-layer PCB, minimal exposed copper area | 3 |
| Package Thermal Resistance, Junction to Ambient (LP, 2-layer PCB) | RθJA | | 40 | | °C/W | LP package; 2-layer PCB, 1-in.² 2-oz copper exposed area | 3 |
| Package Thermal Resistance, Junction to Ambient (LP, 4-layer PCB) | RθJA | | 28 | | °C/W | LP package; 4-layer PCB, based on JEDEC standard | 3 |
| Package Thermal Resistance, Junction to Pad | RθJP | | 2 | | °C/W | LP package | 3 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | is lead (Pb) free, with 100% matte tin leadframes. 29319.37L, Rev. 14 | 1 |
## CAD (KiCad official)
- Symbol: `A3959SLPTR-T`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `a3959slptr-t-etched.step` / `a3959slptr-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `a3959slptr-t.step` / `a3959slptr-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Allegro MicroSystems, LLC datasheet](docs/a3959slptr-t-datasheet.pdf) (12 pp, sha256 `a424976468934aa8`, retrieved 2026-11-11, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/a3959slptr-t-datasheet.pdf)