component
93LC56BT-I/OT
Public Made by Adomby adom
Microchip Tech EEPROM, SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
93LC56BT-I
Microchip Tech · EEPROM · SOT-23-6
93LC56BT-I from Microchip Tech, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DO | tri_state | Data Out returns read data synchronously with CLK (TPD after the positive CLK edge) and shows Ready/Busy status during erase/write; it is High-Z when CS is low or idle. |
| 2 | VSS | power_in | Ground reference for the device; all inputs and outputs are specified with respect to VSS. |
| 3 | DI | input | Data In clocks in the Start bit, opcode, address and data synchronously with CLK on its rising edge. |
| 4 | CLK | input | Serial Clock synchronizes host communication, with opcode, address and data clocked in on its positive edge, and is a don't care while CS is low. |
| 5 | CS | input | Chip Select: a high level selects the device and a low level deselects it into Standby, with CS low for at least 250 ns (TCSL) between consecutive instructions. |
| 6 | VCC | power_in | Power supply for the 93LC56B, specified from 2.5V to 5.5V, with all modes inhibited below a typical VCC of 1.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-6 |
| Category | Memory |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 7 | V | 3 | |||
| All inputs and outputs w.r.t. VSS | -0.6 | V | w.r.t. VSS; max printed as VCC +1.0V | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Ambient temperature with power applied | -40 | 125 | °C | 3 | |||
| ESD protection on all pins | 4 | kV | ESD protection on all pins | 3 | |||
| Supply voltage | VCC | 2.5 | 5.5 | V | 93LC56B device range (Device Selection Table) | 1 | |
| Ambient temperature (Industrial) | TA | -40 | 85 | °C | Industrial (I) grade | 3 | |
| High-level Input Voltage | VIH1 | 2 | V | VCC 2.7V | 3 | ||
| Low-level Input Voltage | VIL1 | -0.3 | 0.8 | V | VCC 2.7V | 3 | |
| Low-level Output Voltage | Vol1 | 0.4 | V | IOL = 2.1 mA, VCC = 4.5V | 3 | ||
| Low-level Output Voltage | Vol2 | 0.2 | V | IOL = 100 µA, VCC = 2.5V | 3 | ||
| High-level Output Voltage | VOH1 | 2.4 | V | IOH = -400 µA, VCC = 4.5V | 3 | ||
| Input Leakage Current | ILI | -1 | 1 | µA | VIN = VSS or VCC | 3 | |
| Output Leakage Current | ILO | -1 | 1 | µA | VOUT = VSS or VCC | 3 | |
| Pin Capacitance (all inputs/outputs) | CIN, COUT | 7 | pF | VIN/VOUT = 0V (Note 1); TA = +25°C, FCLK = 1 MHz | 3 | ||
| Write Current | ICC write | 2 | mA | FCLK = 3 MHz, VCC = 5.5V | 3 | ||
| Read Current | ICC read | 1 | mA | FCLK = 3 MHz, VCC = 5.5V | 3 | ||
| Read Current | ICC read | 500 | µA | FCLK = 2 MHz, VCC = 3.0V | 3 | ||
| Standby Current (I-Temp.) | ICCS | 1 | µA | I-Temp.; CLK = CS = 0V; ORG = DI = VSS or VCC (Note 2 and Note 3) | 3 | ||
| Clock Frequency | FCLK | 2 | MHz | 2.5V VCC < 5.5V | 4 | ||
| Clock High Time | TCKH | 250 | ns | 2.5V VCC < 5.5V | 4 | ||
| Clock Low Time | TCKL | 200 | ns | 2.5V VCC < 5.5V | 4 | ||
| Chip Select Setup Time | TCSS | 100 | ns | 2.5V VCC < 4.5V | 4 | ||
| Chip Select Setup Time | TCSS | 50 | ns | 4.5V VCC < 5.5V | 4 | ||
| Chip Select Hold Time | TCSH | 0 | ns | 1.8V VCC < 5.5V | 4 | ||
| Chip Select Low Time | TCSL | 250 | ns | 1.8V VCC < 5.5V | 4 | ||
| Data Input Setup Time | TDIS | 100 | ns | 2.5V VCC < 5.5V | 4 | ||
| Data Input Hold Time | TDIH | 100 | ns | 2.5V VCC < 5.5V | 4 | ||
| Data Output Delay Time | TPD | 250 | ns | 2.5V VCC < 4.5V, CL = 100 pF | 4 | ||
| Data Output Delay Time | TPD | 200 | ns | 4.5V VCC < 5.5V, CL = 100 pF | 4 | ||
| Data Output Disable Time | TCZ | 200 | ns | 1.8V VCC < 4.5V, (Note 1) | 4 | ||
| Data Output Disable Time | TCZ | 100 | ns | 4.5V VCC < 5.5V, (Note 1) | 4 | ||
| Status Valid Time | TSV | 300 | ns | 2.5V VCC < 4.5V, CL = 100 pF | 4 | ||
| Status Valid Time | TSV | 200 | ns | 4.5V VCC < 5.5V, CL = 100 pF | 4 | ||
| Program Cycle Time | TWC | 6 | ms | Erase/Write mode (AA and LC versions) | 5 | ||
| ERAL Cycle Time | TEC | 6 | ms | ERAL mode, 4.5V VCC 5.5V | 5 | ||
| WRAL Cycle Time | TWL | 15 | ms | WRAL mode, 4.5V VCC 5.5V | 5 | ||
| Endurance | 1 | M cycles | +25°C, VCC = 5.0V (Note 2) | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | Part Number VCC Range ORG Pin Word Size Temperature Ranges Packages 93AA56A 1.8V-5.5V No 8-bit I MC, MS, P, SN, OT, MN, ST | 1 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
93LC56BT-I - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
93lc56bt-i-ot-etched.step/93lc56bt-i-ot-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);93lc56bt-i-ot.step/93lc56bt-i-ot.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
7df346598452af5a, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).