# 24AA025E48T-I

**Microchip Tech** · EEPROM · SOT-23-6

24AA025E48T-I from Microchip Tech, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

## Pinout

| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | Serial clock input that synchronizes data transfer to and from the device, with 400 kHz maximum clock (100 kHz for VCC < 2.5V). |
| 2 | VSS | power_in | Ground reference for the device. |
| 3 | SDA | bidirectional | Open-drain serial address/data I/O that requires a pull-up resistor to VCC (typically 10 kΩ for 100 kHz, 2 kΩ for 400 kHz), and may change only while SCL is low for normal data transfer. |
| 4 | A1 | input | Chip address input compared with the corresponding slave address bit, which must be connected to either VSS or VCC. |
| 5 | A0 | input | Chip address input compared with the corresponding slave address bit, which must be connected to either VSS or VCC. |
| 6 | VCC | power_in | Power supply, +1.7V to 5.5V. |

## Key specifications

| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-6 |
| Category | Memory |
| Pins | 6 |

## Electrical characteristics

Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).

| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| High-Level Input Voltage | VIH | 0.7 |  |  | VCC |  | 3 |
| Low-Level Input Voltage | VIL |  |  | 0.3 | VCC |  | 3 |
| Hysteresis of Schmitt Trigger Inputs | VHYS | 0.05 |  |  | VCC | Note | 3 |
| Low-Level Output Voltage | VOL |  |  | 0.4 | V | IOL = 3.0 mA, VCC = 2.5V | 3 |
| Input Leakage Current | ILI | -1 |  | 1 | µA | VIN = VSS or VCC | 3 |
| Output Leakage Current | ILO | -1 |  | 1 | µA | VOUT = VSS or VCC | 3 |
| Pin Capacitance (all inputs/outputs) | CIN, COUT |  |  | 10 | pF | VCC = 5.0V (Note); TA = 25°C, FCLK = 1 MHz | 3 |
| Operating Current (write) | ICCWRITE |  | 0.1 | 3 | mA | VCC = 5.5V, SCL = 400 kHz | 3 |
| Operating Current (read) | ICCREAD |  | 0.05 | 1 | mA |  | 3 |
| Standby Current, Industrial (I) | ICCS |  | 0.01 | 1 | µA | Industrial (I), SDA = SCL = VCC | 3 |
| Clock Frequency | FCLK |  |  | 400 | kHz | 2.5V VCC 5.5V | 4 |
| Clock Frequency | FCLK |  |  | 100 | kHz | 1.7V VCC 2.5V | 4 |
| Clock High Time | THIGH | 600 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Clock High Time | THIGH | 4000 |  |  | ns | 1.7V VCC 2.5V | 4 |
| Clock Low Time | TLOW | 1300 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Clock Low Time | TLOW | 4700 |  |  | ns | 1.7V VCC 2.5V | 4 |
| SDA and SCL Rise Time | TR |  |  | 300 | ns | 2.5V VCC 5.5V (Note 1) | 4 |
| SDA and SCL Rise Time | TR |  |  | 1000 | ns | 1.7V VCC 2.5V (Note 1) | 4 |
| SDA and SCL Fall Time | TF |  |  | 300 | ns | Note 1 | 4 |
| Start Condition Hold Time | THD:STA | 600 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Start Condition Hold Time | THD:STA | 4000 |  |  | ns | 1.7V VCC 2.5V | 4 |
| Start Condition Setup Time | TSU:STA | 600 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Start Condition Setup Time | TSU:STA | 4700 |  |  | ns | 1.7V VCC 2.5V | 4 |
| Data Input Hold Time | THD:DAT | 0 |  |  | ns | Note 2 | 4 |
| Data Input Setup Time | TSU:DAT | 100 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Data Input Setup Time | TSU:DAT | 250 |  |  | ns | 1.7V VCC 2.5V | 4 |
| Stop Condition Setup Time | TSU:STO | 600 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Stop Condition Setup Time | TSU:STO | 4000 |  |  | ns | 1.7V VCC 2.5V | 4 |
| Output Valid from Clock | TAA |  |  | 900 | ns | 2.5V VCC 5.5V (Note 2) | 4 |
| Output Valid from Clock | TAA |  |  | 3500 | ns | 1.7V VCC 2.5V (Note 2) | 4 |
| Bus Free Time | TBUF | 1300 |  |  | ns | 2.5V VCC 5.5V | 4 |
| Bus Free Time | TBUF | 4700 |  |  | ns | 1.7V VCC 2.5V | 4 |
| Output Fall Time from VIH Minimum to VIL Maximum | TOF |  |  | 250 | ns | 2.5V VCC 5.5V | 4 |
| Input Filter Spike Suppression (SDA and SCL pins) | TSP |  |  | 50 | ns | Notes 1 and 3 | 4 |
| Write Cycle Time (byte or page) | TWC |  |  | 5 | ms |  | 4 |
| Endurance | Endurance | 1 |  |  | M cycles | 25°C (Note 4) | 4 |
| All inputs and outputs w.r.t. VSS |  | -0.3 |  | 1 | V | Maximum printed as VCC +1.0V | 3 |
| Storage temperature |  | -65 |  | 150 | °C |  | 3 |
| Ambient temperature with power applied |  | -40 |  | 125 | °C |  | 3 |
| Supply voltage (operating range) | VCC | 1.7 |  | 5.5 | V | Industrial (I) and Automotive (E) DC characteristics | 3 |
| Ambient temperature, Industrial (I) | TA | -40 |  | 85 | °C | Industrial (I), VCC = 1.7V to 5.5V | 3 |

## Materials and finish

As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).

| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts |  | tin | Package: SN = Plastic SOIC (3.90 mm body), 8-lead OT = SOT-23 (Tape and Reel only) | 29 |

## CAD (KiCad official)

- Symbol: `24AA025E48T-I`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files: `24aa025e48t-i-etched.step` / `24aa025e48t-i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `24aa025e48t-i.step` / `24aa025e48t-i.glb` are the bare package body.

## Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

- **Datasheet:** [Microchip Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586200781875777536) (32 pp, sha256 `f846efffb9da99ee`, retrieved 2026-10-18, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).

[Datasheet PDF](docs/24aa025e48t-i-datasheet.pdf)