main
Ray
Publish 0.1.0
5a0d665
1ED3323MC12NXUMA1
Infineon Technologies · Gate Drive ICs · SOIC-16
1ED3323MC12NXUMA1 from Infineon Technologies, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE2 | power_in | Negative power supply pin of the output chip; if no negative supply voltage is available, all VEE2 pins have to be connected to GND2. |
| 2 | DESAT | input | Desaturation detection input monitoring IGBT VCE; when OUT is high, VCE is above a defined value and the blanking time has expired, protection switches the IGBT off, with blanking time set by an external capacitor. |
| 3 | GND2 | power_in | Reference ground of the output chip. |
| 4 | NC | unconnected | Not connected. |
| 5 | VCC2 | power_in | Positive power supply pin of the output side, typically supplied with 15 V in the datasheet's bipolar and unipolar application examples. |
| 6 | OUT | output | Common output pin to charge and discharge the power transistor gate; during error mode (UVLO, internal error or DESAT) and OFF mode OUT is low. |
| 7 | CLAMP | input | Miller clamp that ties the gate voltage to VEE2 after turn-off once the gate voltage falls below VCLAMP (related to VEE2), designed for a Miller current up to 2 A. |
| 8 | VEE2 | power_in | Negative power supply pin of the output chip; if no negative supply voltage is available, all VEE2 pins have to be connected to GND2. |
| 9 | GND1 | power_in | Ground connection of the input side. |
| 10 | IN+ | input | Non-inverting driver input; the power transistor is on when IN+ is high and IN- is low, a minimum pulse width is defined for glitch robustness, and an internal pull-down ensures the output is low. |
| 11 | IN- | input | Inverting driver input; the power transistor is on when IN- is low and IN+ is high, a minimum pulse width is defined for glitch robustness, and an internal pull-up ensures the output is low. |
| 12 | RDY | output | Open-drain ready status output that is high when both chips are above the UVLO level and the internal chip transmission is faultless. |
| 13 | /FLT | output | Open-drain fault output, low active, which goes low when a desaturation fault of the power transistor occurs. |
| 14 | /RST | input | Reset input, low active: the power transistor is off when /RST is low, and holding it low for time tRST resets the DESAT fault state; an internal pull-up ensures the /FLT status output. |
| 15 | VCC1 | power_in | 5 V or 3.3 V power supply of the input chip. |
| 16 | GND1 | power_in | Ground connection of the input side. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | SOIC-16 |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Positive power supply output side voltage | VVCC2 | -0.3 | 40 | V | in respect to GND2 (note 1) | 18 | |
| Negative power supply output side voltage | VVEE2 | -22 | 0.3 | V | in respect to GND2 (note 1) | 18 | |
| Maximum power supply voltage difference output side | Vmax2 | -0.3 | 40 | V | in respect to VEE2 (note 2) | 18 | |
| Gate driver output current (1ED3323) | IOUT | -9 | 9 | A | t = 1 µs on, 5 µs period; not production tested (notes 3, 4) | 18 | |
| CLAMP output current | ICLAMP | -4.5 | 4.5 | A | t = 1 µs on, 5 µs period; not production tested (notes 3, 4) | 18 | |
| Positive power supply voltage input side | VVCC1 | -0.3 | 7 | V | in respect to GND1 (note 5) | 18 | |
| Logic input voltages IN+, IN-, /RST | VLogicIN | -0.3 | V | in respect to GND1 (note 5); upper limit printed as VVCC1 + 0.3 | 18 | ||
| Open drain output current /FLT, RDY | IFLT, IRDY | 10 | mA | open drain output in low state, output voltage <= VVCC1 | 18 | ||
| DESAT voltage | VDESAT | -0.3 | V | in respect to GND2; IDESAT limited <= 5 mA (note 4); upper limit printed as VVCC2 + 0.3 | 18 | ||
| Input to output offset voltage | VOFFSET | 2300 | V | VVEE2,max - VVEE2,min with VVEE2,max >= VGND1 >= VVEE2,min; for functional operation only (note 6) | 19 | ||
| Junction temperature | TJ | -40 | 150 | °C | 19 | ||
| Storage temperature | TST | -55 | 150 | °C | 19 | ||
| Power dissipation input part | PDIN | 100 | mW | @ TA = 85°C | 19 | ||
| Power dissipation output part DSO-16 wide body | PDOUT-16 | 810 | mW | @ TA = 85°C, JEDEC 2s2p, no cooling | 19 | ||
| ESD capability HBM model | VESDHBM | -4 | 4 | kV | HBM model according to ANSI/ESDA/JEDEC JS-001 | 19 | |
| Maximum switching frequency | fSW | 1 | MHz | 19 | |||
| Positive power supply output side | VVCC2 | 35 | V | in respect to GND2 (note 1); lower limit printed as VUVLOH2 | 20 | ||
| Negative power supply output side | VVEE2 | -20 | 0 | V | in respect to GND2 (note 1) | 20 | |
| Power supply difference output side | Vmax2 | 35 | V | Vmax2 = VVCC2 - VVEE2 (note 2) | 20 | ||
| Power supply input side | VVCC1 | 5.5 | V | in respect to GND1 (note 3); lower limit printed as VUVLOH1 | 20 | ||
| Logic input voltages | VLogicIN | -0.3 | V | in respect to GND1 (note 3); upper limit printed as VVCC1 | 20 | ||
| DESAT voltage | VDESAT | -0.3 | V | in respect to GND2 (note 1); upper limit printed as VVCC2 + 0.3 | 20 | ||
| Ambient temperature | TA | -40 | 125 | °C | 20 | ||
| Operating junction temperature | TJop | -40 | 150 | °C | 20 | ||
| Common Mode Transient Immunity | CMTI | -300 | 300 | kV/µs | @ VISO = 1.5 kV; not production tested (note 4) | 20 | |
| UVLO threshold output side (on), 1ED3323 | VUVLOH2 | 12 | 12.6 | V | VVCC2-VGND2, 1ED3323 | 21 | |
| UVLO threshold output side (off), 1ED3323 | VUVLOL2 | 10.4 | 11 | V | VVCC2-VGND2, 1ED3323 | 21 | |
| UVLO hysteresis output side | VHYS2 | 0.6 | 0.9 | V | VUVLOH2 - VUVLOL2 | 21 | |
| UVLO hysteresis input side | VHYS1 | 0.1 | 0.2 | V | VUVLOH1 - VUVLOL1 | 21 | |
| Quiescent current input side | IQ1 | 1.1 | 3 | mA | VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -8 V, IN+ High, IN- Low, OUT High, RDY High, /FLT High, VDESAT = 0 V (note 1) | 21 | |
| Quiescent current output side | IQ2 | 2 | 3 | mA | VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -8 V, IN+ High, IN- Low, OUT High, RDY High, /FLT High, VDESAT = 0 V (note 1) | 21 | |
| Digital input current IN-, /RST | IIN-, IRST | -200 | -40 | µA | VIN- = GND1, VRST = GND1 | 21 | |
| Digital input current IN+ | IIN+ | 40 | 200 | µA | VIN+ = VVCC1 | 21 | |
| Digital pull up current RDY, /FLT | IPRDY, IPFLT | -400 | -100 | µA | VRDY = GND1, VFLT = GND1 | 21 | |
| High level output peak current (1ED3323) | IOUTH | 4 | 6 | A | IN+ High, IN- Low, VOUT = VVCC2 - 15 V, VVCC2 = 15 V, CL = 100 nF, RL = 0.1 Ohm (note 1) | 22 | |
| High level output on resistance (1ED3323) | RDSON,H | 0.5 | 0.79 | 1.3 | Ω | IOUTH = 0.1 A | 22 |
| Low level output peak current (1ED3323) | IOUTL | 4 | 8.5 | A | IN+ Low, IN- Low, OUT = VVEE2 + 15 V, VVCC2 = 15 V, CL = 100 nF, RL = 0.1 Ohm (note 4) | 22 | |
| Low level output on resistance (1ED3323) | RDSON,L | 0.35 | 0.51 | 0.85 | Ω | IOUTL = 0.1 A | 22 |
| Short circuit clamp voltage OUT / VCC2 (1ED3323) | VCLP_OUT | 1 | 1.5 | V | path off, IOUT = 500 mA, t < 10 µs; not production tested (note 6) | 22 | |
| Low level clamp current | ICLAMP,L | 2 | 3 | A | VCLAMP = 1.5 V, VVCC2 = 15 V, VVEE2 = 0 V, Rg = 0.1 Ω, Cg = 1 µF (note 1) | 23 | |
| Low level clamp on resistance | RDSON,CLP | 0.4 | 0.6 | 1 | Ω | IOUTL = 0.1 A | 23 |
| Clamp threshold voltage | VCLAMP | 1.6 | 2.1 | 2.4 | V | in respect to VEE2 | 23 |
| Short circuit clamp voltage CLAMP / VCC2 | VCLP | 1.8 | 2 | V | path off, ICLAMP = 500 mA, t < 10 µs (note 1) | 23 | |
| Input IN+, IN-, /RST to output propagation delay on | tPDON | 74 | 80 | 84 | ns | CLOAD = 100 pF, VIN+ = 70 %, VOUT = 20 %, TA = 25 °C | 23 |
| Input IN+, IN-, /RST to output propagation delay off | tPDOFF | 81 | 86 | 92 | ns | CLOAD = 100 pF, VIN+ = 30 %, VOUT = 80 %, TA = 25 °C | 23 |
| Input IN+, IN-, /RST pulse suppression time (filter time) | tINFLT | 29 | 35 | 41 | ns | shorter pulses will not propagate to the output | 23 |
| Rise time 1 | trise1 | 15 | 20 | ns | CLOAD = 1 nF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V | 24 | |
| Rise time 2 | trise2 | 10 | 15 | ns | CLOAD = 100 pF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V (note 1) | 24 | |
| Fall time 1 | tfall1 | 15 | 20 | ns | CLOAD = 1 nF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V | 24 | |
| Fall time 2 | tfall2 | 10 | 15 | ns | CLOAD = 100 pF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V (note 1) | 24 | |
| Blanking capacitor charge current | IDESATC | 438 | 510 | 582 | µA | VVCC2 = 15 V, VVEE2 = GND2, VDESAT - VGND2 = 2 V | 24 |
| Blanking capacitor discharge current | IDESATD | 90 | 150 | mA | VVCC2 = 15 V, VVEE2 = GND2, VDESAT - VGND2 = 6 V | 24 | |
| Desaturation reference level | VDESATth | 8.5 | 9 | 9.5 | V | VVCC2 = 15 V, in respect to GND2 | 24 |
| Desaturation sense to out low delay (1ED3323) | tDESATOUT | 350 | 430 | ns | VOUT = 90 %, COUT = 1 nF, OUT = OUTH + OUTL shorted | 25 | |
| Desaturation low voltage | VDESATL | 0.25 | 0.5 | 0.95 | V | IN+ = Low, IN- = Low, OUT(H,L) = Low, IDESAT = 70 mA | 25 |
| Leading edge blanking | tDESATleb | 280 | 400 | 500 | ns | 25 | |
| Short circuit clamp voltage desat / vcc2 | VCLP_DESAT | 1.4 | 1.6 | V | path off, IDESAT = 500 mA, t < 10 µs (note 1) | 25 | |
| Active shut down voltage | VACTSD | 2 | 2.6 | V | IOUT = 200 mA; VVCC2 = open | 25 | |
| Thermal resistance junction to ambient DSO-16 wide body, JEDEC 1s0p PCB with cooling | RTHJAwc | 86.7 | K/W | @ TA = 85 °C, PDIN = 100 mW, PDOUT = 650 mW, JEDEC 1s0p PCB, DSO-16 wide body with cooling | 19 | ||
| Thermal resistance junction to ambient DSO-16 wide body, JEDEC 2s2p PCB no cooling | RTHJAnc | 71.4 | K/W | @ TA = 85 °C, PDIN = 100 mW, PDOUT = 810 mW, JEDEC 2s2p PCB, DSO-16 wide body no cooling | 19 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | Copper | dissipation. The 1ED332xMC12N is conceived to dissipate most of the heat generated through this pins. Figure 16 Reference layout for thermal data (Copper thickness 102 μm) | 30 |
CAD (KiCad official)
- Symbol:
1ED3323MC12NXUMA1 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
1ed3323mc12nxuma1-etched.step/1ed3323mc12nxuma1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);1ed3323mc12nxuma1.step/1ed3323mc12nxuma1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (33 pp, sha256
8b0f42f9805be5a6, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# 1ED3323MC12NXUMA1
**Infineon Technologies** · Gate Drive ICs · SOIC-16
1ED3323MC12NXUMA1 from Infineon Technologies, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE2 | power_in | Negative power supply pin of the output chip; if no negative supply voltage is available, all VEE2 pins have to be connected to GND2. |
| 2 | DESAT | input | Desaturation detection input monitoring IGBT VCE; when OUT is high, VCE is above a defined value and the blanking time has expired, protection switches the IGBT off, with blanking time set by an external capacitor. |
| 3 | GND2 | power_in | Reference ground of the output chip. |
| 4 | NC | unconnected | Not connected. |
| 5 | VCC2 | power_in | Positive power supply pin of the output side, typically supplied with 15 V in the datasheet's bipolar and unipolar application examples. |
| 6 | OUT | output | Common output pin to charge and discharge the power transistor gate; during error mode (UVLO, internal error or DESAT) and OFF mode OUT is low. |
| 7 | CLAMP | input | Miller clamp that ties the gate voltage to VEE2 after turn-off once the gate voltage falls below VCLAMP (related to VEE2), designed for a Miller current up to 2 A. |
| 8 | VEE2 | power_in | Negative power supply pin of the output chip; if no negative supply voltage is available, all VEE2 pins have to be connected to GND2. |
| 9 | GND1 | power_in | Ground connection of the input side. |
| 10 | IN+ | input | Non-inverting driver input; the power transistor is on when IN+ is high and IN- is low, a minimum pulse width is defined for glitch robustness, and an internal pull-down ensures the output is low. |
| 11 | IN- | input | Inverting driver input; the power transistor is on when IN- is low and IN+ is high, a minimum pulse width is defined for glitch robustness, and an internal pull-up ensures the output is low. |
| 12 | RDY | output | Open-drain ready status output that is high when both chips are above the UVLO level and the internal chip transmission is faultless. |
| 13 | /FLT | output | Open-drain fault output, low active, which goes low when a desaturation fault of the power transistor occurs. |
| 14 | /RST | input | Reset input, low active: the power transistor is off when /RST is low, and holding it low for time tRST resets the DESAT fault state; an internal pull-up ensures the /FLT status output. |
| 15 | VCC1 | power_in | 5 V or 3.3 V power supply of the input chip. |
| 16 | GND1 | power_in | Ground connection of the input side. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | SOIC-16 |
| Category | Power Management |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Positive power supply output side voltage | VVCC2 | -0.3 | | 40 | V | in respect to GND2 (note 1) | 18 |
| Negative power supply output side voltage | VVEE2 | -22 | | 0.3 | V | in respect to GND2 (note 1) | 18 |
| Maximum power supply voltage difference output side | Vmax2 | -0.3 | | 40 | V | in respect to VEE2 (note 2) | 18 |
| Gate driver output current (1ED3323) | IOUT | -9 | | 9 | A | t = 1 µs on, 5 µs period; not production tested (notes 3, 4) | 18 |
| CLAMP output current | ICLAMP | -4.5 | | 4.5 | A | t = 1 µs on, 5 µs period; not production tested (notes 3, 4) | 18 |
| Positive power supply voltage input side | VVCC1 | -0.3 | | 7 | V | in respect to GND1 (note 5) | 18 |
| Logic input voltages IN+, IN-, /RST | VLogicIN | -0.3 | | | V | in respect to GND1 (note 5); upper limit printed as VVCC1 + 0.3 | 18 |
| Open drain output current /FLT, RDY | IFLT, IRDY | | | 10 | mA | open drain output in low state, output voltage <= VVCC1 | 18 |
| DESAT voltage | VDESAT | -0.3 | | | V | in respect to GND2; IDESAT limited <= 5 mA (note 4); upper limit printed as VVCC2 + 0.3 | 18 |
| Input to output offset voltage | VOFFSET | | | 2300 | V | VVEE2,max - VVEE2,min with VVEE2,max >= VGND1 >= VVEE2,min; for functional operation only (note 6) | 19 |
| Junction temperature | TJ | -40 | | 150 | °C | | 19 |
| Storage temperature | TST | -55 | | 150 | °C | | 19 |
| Power dissipation input part | PDIN | | | 100 | mW | @ TA = 85°C | 19 |
| Power dissipation output part DSO-16 wide body | PDOUT-16 | | | 810 | mW | @ TA = 85°C, JEDEC 2s2p, no cooling | 19 |
| ESD capability HBM model | VESDHBM | -4 | | 4 | kV | HBM model according to ANSI/ESDA/JEDEC JS-001 | 19 |
| Maximum switching frequency | fSW | | | 1 | MHz | | 19 |
| Positive power supply output side | VVCC2 | | | 35 | V | in respect to GND2 (note 1); lower limit printed as VUVLOH2 | 20 |
| Negative power supply output side | VVEE2 | -20 | | 0 | V | in respect to GND2 (note 1) | 20 |
| Power supply difference output side | Vmax2 | | | 35 | V | Vmax2 = VVCC2 - VVEE2 (note 2) | 20 |
| Power supply input side | VVCC1 | | | 5.5 | V | in respect to GND1 (note 3); lower limit printed as VUVLOH1 | 20 |
| Logic input voltages | VLogicIN | -0.3 | | | V | in respect to GND1 (note 3); upper limit printed as VVCC1 | 20 |
| DESAT voltage | VDESAT | -0.3 | | | V | in respect to GND2 (note 1); upper limit printed as VVCC2 + 0.3 | 20 |
| Ambient temperature | TA | -40 | | 125 | °C | | 20 |
| Operating junction temperature | TJop | -40 | | 150 | °C | | 20 |
| Common Mode Transient Immunity | CMTI | -300 | | 300 | kV/µs | @ VISO = 1.5 kV; not production tested (note 4) | 20 |
| UVLO threshold output side (on), 1ED3323 | VUVLOH2 | 12 | | 12.6 | V | VVCC2-VGND2, 1ED3323 | 21 |
| UVLO threshold output side (off), 1ED3323 | VUVLOL2 | 10.4 | | 11 | V | VVCC2-VGND2, 1ED3323 | 21 |
| UVLO hysteresis output side | VHYS2 | 0.6 | | 0.9 | V | VUVLOH2 - VUVLOL2 | 21 |
| UVLO hysteresis input side | VHYS1 | 0.1 | | 0.2 | V | VUVLOH1 - VUVLOL1 | 21 |
| Quiescent current input side | IQ1 | 1.1 | | 3 | mA | VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -8 V, IN+ High, IN- Low, OUT High, RDY High, /FLT High, VDESAT = 0 V (note 1) | 21 |
| Quiescent current output side | IQ2 | 2 | | 3 | mA | VVCC1 = 5 V, VVCC2 = 15 V, VVEE2 = -8 V, IN+ High, IN- Low, OUT High, RDY High, /FLT High, VDESAT = 0 V (note 1) | 21 |
| Digital input current IN-, /RST | IIN-, IRST | -200 | | -40 | µA | VIN- = GND1, VRST = GND1 | 21 |
| Digital input current IN+ | IIN+ | 40 | | 200 | µA | VIN+ = VVCC1 | 21 |
| Digital pull up current RDY, /FLT | IPRDY, IPFLT | -400 | | -100 | µA | VRDY = GND1, VFLT = GND1 | 21 |
| High level output peak current (1ED3323) | IOUTH | 4 | | 6 | A | IN+ High, IN- Low, VOUT = VVCC2 - 15 V, VVCC2 = 15 V, CL = 100 nF, RL = 0.1 Ohm (note 1) | 22 |
| High level output on resistance (1ED3323) | RDSON,H | 0.5 | 0.79 | 1.3 | Ω | IOUTH = 0.1 A | 22 |
| Low level output peak current (1ED3323) | IOUTL | 4 | | 8.5 | A | IN+ Low, IN- Low, OUT = VVEE2 + 15 V, VVCC2 = 15 V, CL = 100 nF, RL = 0.1 Ohm (note 4) | 22 |
| Low level output on resistance (1ED3323) | RDSON,L | 0.35 | 0.51 | 0.85 | Ω | IOUTL = 0.1 A | 22 |
| Short circuit clamp voltage OUT / VCC2 (1ED3323) | VCLP_OUT | 1 | | 1.5 | V | path off, IOUT = 500 mA, t < 10 µs; not production tested (note 6) | 22 |
| Low level clamp current | ICLAMP,L | 2 | | 3 | A | VCLAMP = 1.5 V, VVCC2 = 15 V, VVEE2 = 0 V, Rg = 0.1 Ω, Cg = 1 µF (note 1) | 23 |
| Low level clamp on resistance | RDSON,CLP | 0.4 | 0.6 | 1 | Ω | IOUTL = 0.1 A | 23 |
| Clamp threshold voltage | VCLAMP | 1.6 | 2.1 | 2.4 | V | in respect to VEE2 | 23 |
| Short circuit clamp voltage CLAMP / VCC2 | VCLP | 1.8 | | 2 | V | path off, ICLAMP = 500 mA, t < 10 µs (note 1) | 23 |
| Input IN+, IN-, /RST to output propagation delay on | tPDON | 74 | 80 | 84 | ns | CLOAD = 100 pF, VIN+ = 70 %, VOUT = 20 %, TA = 25 °C | 23 |
| Input IN+, IN-, /RST to output propagation delay off | tPDOFF | 81 | 86 | 92 | ns | CLOAD = 100 pF, VIN+ = 30 %, VOUT = 80 %, TA = 25 °C | 23 |
| Input IN+, IN-, /RST pulse suppression time (filter time) | tINFLT | 29 | 35 | 41 | ns | shorter pulses will not propagate to the output | 23 |
| Rise time 1 | trise1 | 15 | 20 | | ns | CLOAD = 1 nF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V | 24 |
| Rise time 2 | trise2 | 10 | 15 | | ns | CLOAD = 100 pF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V (note 1) | 24 |
| Fall time 1 | tfall1 | 15 | 20 | | ns | CLOAD = 1 nF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V | 24 |
| Fall time 2 | tfall2 | 10 | 15 | | ns | CLOAD = 100 pF, VL 20 %, VH 80 %, VVCC2 = 15 V, VVEE2 = GND2 = 0 V (note 1) | 24 |
| Blanking capacitor charge current | IDESATC | 438 | 510 | 582 | µA | VVCC2 = 15 V, VVEE2 = GND2, VDESAT - VGND2 = 2 V | 24 |
| Blanking capacitor discharge current | IDESATD | 90 | | 150 | mA | VVCC2 = 15 V, VVEE2 = GND2, VDESAT - VGND2 = 6 V | 24 |
| Desaturation reference level | VDESATth | 8.5 | 9 | 9.5 | V | VVCC2 = 15 V, in respect to GND2 | 24 |
| Desaturation sense to out low delay (1ED3323) | tDESATOUT | 350 | | 430 | ns | VOUT = 90 %, COUT = 1 nF, OUT = OUTH + OUTL shorted | 25 |
| Desaturation low voltage | VDESATL | 0.25 | 0.5 | 0.95 | V | IN+ = Low, IN- = Low, OUT(H,L) = Low, IDESAT = 70 mA | 25 |
| Leading edge blanking | tDESATleb | 280 | 400 | 500 | ns | | 25 |
| Short circuit clamp voltage desat / vcc2 | VCLP_DESAT | 1.4 | | 1.6 | V | path off, IDESAT = 500 mA, t < 10 µs (note 1) | 25 |
| Active shut down voltage | VACTSD | 2 | | 2.6 | V | IOUT = 200 mA; VVCC2 = open | 25 |
| Thermal resistance junction to ambient DSO-16 wide body, JEDEC 1s0p PCB with cooling | RTHJAwc | | 86.7 | | K/W | @ TA = 85 °C, PDIN = 100 mW, PDOUT = 650 mW, JEDEC 1s0p PCB, DSO-16 wide body with cooling | 19 |
| Thermal resistance junction to ambient DSO-16 wide body, JEDEC 2s2p PCB no cooling | RTHJAnc | | 71.4 | | K/W | @ TA = 85 °C, PDIN = 100 mW, PDOUT = 810 mW, JEDEC 2s2p PCB, DSO-16 wide body no cooling | 19 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | Copper | | dissipation. The 1ED332xMC12N is conceived to dissipate most of the heat generated through this pins. Figure 16 Reference layout for thermal data (Copper thickness 102 μm) | 30 |
## CAD (KiCad official)
- Symbol: `1ED3323MC12NXUMA1`
- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`
- 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files: `1ed3323mc12nxuma1-etched.step` / `1ed3323mc12nxuma1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `1ed3323mc12nxuma1.step` / `1ed3323mc12nxuma1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Infineon Technologies datasheet](docs/1ed3323mc12nxuma1-datasheet.pdf) (33 pp, sha256 `8b0f42f9805be5a6`, retrieved 2026-11-05, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/1ed3323mc12nxuma1-datasheet.pdf)