component
cat25160vi-gt3
Public Unreviewedby Ray
onsemi EEPROM, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
README
markdownCAT25160VI-GT3
onsemi · EEPROM · SOIC-8
CAT25160VI-GT3 from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Active-low chip select. Every SPI transaction must begin with a high-to-low transition and end with a low-to-high transition on CS. When CS is high, SO is tri-stated and the device enters standby mode (unless an internal write is in progress). VIL = -0.5 V to 0.3VCC, VIH = 0.7VCC to VCC+0.5 V. |
| 2 | SO | output | Serial data output. Data is shifted out on the falling edge of SCK in SPI modes (0,0) and (1,1). High-impedance when CS is high or during a HOLD condition. Drives VOL = 0.4 V @ 3 mA (VCC>2.5 V) and VOH = VCC-0.8 V @ -1.6 mA. |
| 3 | WP | input | Active-low write protect. When WP is held low and the WPEN bit in the Status Register is set to '1', writes to the Status Register are disabled, providing hardware write protection. Tie high to allow normal write operations. |
| 4 | VSS | power_in | Ground reference for the device (0 V). |
| 5 | SI | input | Serial data input. Accepts op-codes, addresses, and data. Data is latched on the rising edge of SCK in SPI modes (0,0) and (1,1). |
| 6 | SCK | input | Serial clock input from the SPI host. Synchronizes data transfer on SI and SO. Supports DC to 20 MHz operation at VCC = 4.5-5.5 V (10 MHz at 2.5-5.5 V, 5 MHz at 1.8-5.5 V). |
| 7 | HOLD | input | Active-low hold input used to pause SPI communication without retransmitting the sequence. To pause, drive HOLD low while SCK is low; to resume, drive HOLD high while SCK is low. When not used, tie to VCC directly or via a pull-up resistor. |
| 8 | VCC | power_in | Positive supply, 1.8 V to 5.5 V. Typical supply current is 2 mA during read/write at 10 MHz; standby current is ~2 uA (WP=VCC) or 4-5 uA (WP=GND). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Ordering variants
CAT25160VI-GT3CAT25160VI-GT3VE-GT3CAT25160VI-GT3YI-GT3CAT25160VI-GT3YE-GT3CAT25160VI-GT3HU4I-GT3
CAD (KiCad official)
- Symbol:
CAT25160VI-GT3 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (None pp, sha256
4c0a7cb4acb58659, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).