component
AP2401MP-13
Public Unreviewedby Ray
Diodes Incorporated AC-DC Controllers and Regulators, MSOP-8-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads when scrolled away or the tab is hidden.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads when scrolled away or the tab is hidden.
PCB Footprint
Open full view ↗Loads on click. Unloads when scrolled away or the tab is hidden.
Datasheet
Open in new tab ↗Loads on click. Unloads when scrolled away or the tab is hidden.
README
markdownAP2401MP-13
Diodes Incorporated · AC-DC Controllers and Regulators · MSOP-8-EP
AP2401MP-13 from Diodes Incorporated, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Device ground reference. All voltages are referenced to this pin. |
| 2 | IN | power_in | Voltage input pin (2.7 V to 5.5 V). Both IN pins must be tied together externally. Place a 0.1 µF or larger ceramic capacitor from IN to GND as close as possible. |
| 3 | IN | power_in | Voltage input pin (2.7 V to 5.5 V). Both IN pins must be tied together externally. Place a 0.1 µF or larger ceramic capacitor from IN to GND as close as possible. |
| 4 | EN | input | Enable input, active low on AP2401. VIL ≤ 0.8 V asserts enable; VIH ≥ 2 V disables the switch. Leakage <1 µA typical. |
| 5 | FLG | output | Fault flag output. Active-low open-drain that reports over-temperature and over-current with a 7 ms typical deglitch/blanking time. Requires an external pull-up resistor (typical 10 kΩ). FLG is disabled for 7 ms after turn-on. |
| 6 | OUT | power_out | Switched voltage output pin. Both OUT pins must be tied together externally. Typical bulk capacitance ≥120 µF plus 0.1 µF ceramic recommended on output. |
| 7 | OUT | power_out | Switched voltage output pin. Both OUT pins must be tied together externally. Typical bulk capacitance ≥120 µF plus 0.1 µF ceramic recommended on output. |
| 8 | NC | unconnected | No internal connection. Recommended to tie to OUT pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | MSOP-8-EP |
| Category | PMIC |
| Pins | 8 |
Ordering variants
Same part, different packaging or reel option.
AP2401MP-13SAP2401MP-13AP2401MP-13MPEAP2401MP-13FN4AP2401MP-13SN2
CAD (KiCad official)
- Symbol:
AP2401MP-13 - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (18 pp, sha256
8a66a76a7185a51e, retrieved 2026-08-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).