Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LMK1D1204RGTR

Texas Instruments · Pre-ordered Products · VQFN-16(3x3)

LMK1D1204RGTR from Texas Instruments, in a VQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground.
2 IN_SEL input Input select with an internal 500kΩ pullup and 320kΩ pulldown resistor that selects the input port (IN0 or IN1); if left open, the outputs are disabled (logic low).
3 IN1_P input Secondary clock input, positive side of a differential pair or single-ended input.
4 IN1_N input Secondary clock input, negative side of a differential pair; when driving single-ended, apply the appropriate bias voltage to this unused pin.
5 VDD power_in Device power supply of 1.8V, 2.5V or 3.3V (1.71V to 3.465V).
6 IN0_P input Primary clock input, positive side of a differential pair or single-ended input.
7 IN0_N input Primary clock input, negative side of a differential pair; when driving single-ended, apply the appropriate bias voltage to this unused pin.
8 VAC_REF0 output Bias voltage output for capacitive-coupled inputs; if used, TI recommends a 0.1µF capacitor to GND on this pin.
9 OUT0_P output Differential LVDS output pair number 0, positive side.
10 OUT0_N output Differential LVDS output pair number 0, negative side.
11 OUT1_P output Differential LVDS output pair number 1, positive side.
12 OUT1_N output Differential LVDS output pair number 1, negative side.
13 OUT2_P output Differential LVDS output pair number 2, positive side.
14 OUT2_N output Differential LVDS output pair number 2, negative side.
15 OUT3_P output Differential LVDS output pair number 3, positive side.
16 OUT3_N output Differential LVDS output pair number 3, negative side.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-16(3x3)
Category Solders / Accessories / Batteries
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDD -0.3 3.6 V 8
Input voltage VIN -0.3 3.6 V 8
Output voltage VO -0.3 V max printed as VDD + 0.3 8
Input current IIN -20 20 mA 8
Continuous output current IO -50 50 mA 8
Junction temperature TJ 135 °C 8
Storage temperature Tstg -65 150 °C Device unpowered 8
ESD HBM V(ESD) -3000 3000 V Human body model, all pins 8
ESD CDM V(ESD) -1000 1000 V Charged device model, all pins 8
Core supply voltage 3.3V VDD 3.135 3.3 3.465 V 3.3V supply 8
Core supply voltage 2.5V VDD 2.375 2.5 2.625 V 2.5V supply 8
Core supply voltage 1.8V VDD 1.71 1.8 1.89 V 1.8V supply 8
Supply voltage ramp Supply Ramp 0.1 20 ms Requires monotonic ramp (10-90% of VDD) 8
Operating free-air temperature TA -40 105 °C 8
Operating junction temperature TJ -40 135 °C 8
Junction-to-ambient thermal resistance RθJA 48.7 °C/W VQFN 16 pins 9
Junction-to-case (top) thermal resistance RθJC(top) 56.4 °C/W VQFN 16 pins 9
Junction-to-board thermal resistance RθJB 23.6 °C/W VQFN 16 pins 9
Junction-to-top characterization parameter ΨJT 1.6 °C/W VQFN 16 pins 9
Junction-to-board characterization parameter ΨJB 23.6 °C/W VQFN 16 pins 9
Junction-to-case (bottom) thermal resistance RθJC(bot) 8.6 °C/W VQFN 16 pins 9
Static supply current LMK1D1204 IDDSTAT 50 mA All-outputs enabled and unterminated, f = 0Hz 9
Supply current at 100MHz LMK1D1204 IDD100M 60 72 mA All-outputs enabled, RL = 100Ω, f =100MHz 9
Input low voltage VIL -0.3 V Maximum input voltage for a logical "0" state; max printed as 0.3 × VCC 9
Input high current IIH 30 µA VDD can be 1.8V/2.5V/3.3V with VIH = VDD 9
Input low current IIL -30 µA VDD can be 1.8V/2.5V/3.3V with VIH = VDD 9
Input pullup resistor Rpull-up(EN) 500 kΩ 9
Input pulldown resistor Rpull-down(EN) 320 kΩ 9
Input frequency (LVCMOS) fIN 250 MHz Clock input, single-ended 9
Single-ended input voltage swing VIN_S-E 0.4 3.465 V Assumes a square wave input with two levels 9
Input slew rate dVIN/dt 0.05 V/ns 20% to 80% of the amplitude 9
Input high current (LVCMOS) IIH 50 µA VDD = 3.465V, VIH = 3.465V 9
Input low current (LVCMOS) IIL -30 µA VDD = 3.465V, VIL = 0V 9
Input capacitance (LVCMOS) CIN_SE 3.5 pF at 25°C 9
Input frequency (differential) fIN 2 GHz Clock input 9
Differential input voltage peak-to-peak VIN,DIFF(p-p) 0.3 2.4 VPP VICM = 1V (VDD = 1.8V) 9
Input common mode voltage VICM 0.25 2.3 V VIN,DIFF(P-P) > 0.4V (VDD = 1.8V/2.5/3.3V) 10
Input high current (differential) IIH 30 µA VDD = 3.465V, VINP = 2.4V, VINN = 1.2V 10
Input low current (differential) IIL -30 µA VDD = 3.465V, VINP = 0V, VINN = 1.2V 10
Input capacitance (Single-ended) CIN_S-E 3.5 pF at 25°C 10
Differential output voltage magnitude /VOD/ 250 350 450 mV VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω 10
Change in differential output voltage magnitude ΔVOD -15 15 mV VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω 10
Steady-state common mode output voltage (1.8V) VOC(SS) 1 1.2 V VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω (VDD = 1.8V) 10
Steady-state common mode output voltage (2.5V/3.3V) VOC(SS) 1.1 1.375 V VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω (VDD = 2.5V/3.3V) 10
Change in steady-state common mode output voltage ΔVOC(SS) -15 15 mV VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω 10
Output overshoot and undershoot Vring -0.1 0.1 VOD VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω, fOUT = 491.52MHz 10
Output AC common mode VOS 50 100 mVpp VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω 10
Short-circuit output current (differential) IOS -12 12 mA VOUTP = VOUTN 10
Short-circuit output current (common-mode) IOS(cm) -24 24 mA VOUTP = VOUTN = 0 10
Propagation delay tPD 0.3 0.575 ns VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω 10
Part-to-part skew tSK, PP 250 ps Skew between outputs on different parts subjected to the same operating conditions with the same input and output loading. 10
Pulse skew tSK, P -20 20 ps 50% duty cycle input, crossing point-to-crossing point distortion 10
Random additive jitter (rms) tRJIT(ADD) 50 60 fs, RMS fIN = 156.25MHz with 50% duty-cycle, Input slew rate = 1.5V/ns, Integration range = 12kHz - 20MHz, RLOAD = 100Ω 10
Output duty cycle ODC 45 55 % With 50% duty cycle input 12
Output rise and fall time tR/tF 300 ps 20% to 80% with RLOAD = 100Ω 12
Reference output voltage VAC_REF 0.9 1.25 1.375 V VDD = 2.5V, ILOAD = 100 µA 12
Mux isolation MUXISO 80 dB fIN = 156.25MHz 12
Phase noise at 1kHz PN1kHz -143 dBc/Hz 156.25MHz carrier, input slew rate = 1.5V/ns, RLOAD = 100Ω 11
Phase noise at 10kHz PN10kHz -152 dBc/Hz 156.25MHz carrier, input slew rate = 1.5V/ns, RLOAD = 100Ω 11
Phase noise at 100kHz PN100kHz -157 dBc/Hz 156.25MHz carrier, input slew rate = 1.5V/ns, RLOAD = 100Ω 11
Phase noise at 1MHz PN1MHz -160 dBc/Hz 156.25MHz carrier, input slew rate = 1.5V/ns, RLOAD = 100Ω 11
Phase noise floor PNfloor -164 dBc/Hz 156.25MHz carrier, input slew rate = 1.5V/ns, RLOAD = 100Ω 11
Power supply noise rejection 10kHz PSNR -70 dBc 10kHz, 100mVpp ripple injected on VDD 12
Power supply noise rejection 1MHz PSNR -50 dBc 1MHz, 100mVpp ripple injected on VDD 12

CAD (KiCad official)

  • Symbol: LMK1D1204RGTR
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: VQFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: lmk1d1204rgtr-etched.step / lmk1d1204rgtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmk1d1204rgtr.step / lmk1d1204rgtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (39 pp, sha256 5a91756f0fddf2e4, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF