3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownADUM5201CRWZ-RL
Analog Devices · Digital Isolators · SOIC-16-300mil
ADUM5201CRWZ-RL from Analog Devices, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD1 | power_in | Primary supply voltage, 3.0 V to 5.5 V. |
| 2 | GND1 | power_in | Ground 1, the ground reference for the isolator primary side; pins 2 and 8 are internally connected and both should be tied to a common ground. |
| 3 | VIA | input | Logic input A; the pin function table gives no further electrical limits for this pin. |
| 4 | VOB | output | Logic output B on the primary side; the output is high-Z when VE1 is low. |
| 5 | RCIN | input | Regulation control input that must be connected to the RCOUT pin of a master isoPower device or tied low, and must not be tied high while RCSEL is low. |
| 6 | RCSEL | input | Selects self-regulation mode (high) or slave mode (low); the pin is weakly pulled high and should be tied high or low in noisy environments. |
| 7 | VE1 | input | Primary data enable; when high or not connected the primary output is active, and when low the output is in a high-Z state. |
| 8 | GND1 | power_in | Ground 1, the ground reference for the isolator primary side; internally connected to pin 2 and should be tied to a common ground. |
| 9 | GNDISO | power_in | Ground reference for isolator side 2; internally connected to pin 15 and should be tied to a common ground. |
| 10 | VE2 | input | Secondary data enable; when high or not connected the secondary output is active, and when low the output is in a high-Z state. |
| 11 | VSEL | input | Output voltage selection; VSEL = VISO sets the VISO setpoint to 5.0 V, VSEL = GNDISO sets it to 3.3 V, and the pin has no function in slave regulation mode. |
| 12 | NC | unconnected | No internal connection. |
| 13 | VIB | input | Logic input B on the secondary (VISO) side; the pin function table gives no further electrical limits for this pin. |
| 14 | VOA | output | Logic output A on the secondary (VISO) side; the output is high-Z when VE2 is low. |
| 15 | GNDISO | power_in | Ground reference for isolator side 2; internally connected to pin 9 and should be tied to a common ground. |
| 16 | VISO | power_out | Secondary supply voltage output for the secondary-side isolated data channels and external loads; the setpoint is 5.0 V or 3.3 V as selected by VSEL. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOIC-16-300mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature | TA | -40 | 105 | °C | 10 | ||
| Supply Voltage VDD1 @ VSEL = 0 V | VDD1 | 3 | 5.5 | V | VSEL = 0 V | 10 | |
| Supply Voltage VDD1 @ VSEL = VISO | VDD1 | 4.5 | 5.5 | V | VSEL = VISO | 10 | |
| Storage Temperature Range | TST | -55 | 150 | °C | 11 | ||
| Ambient Operating Temperature Range | TA | -40 | 105 | °C | 11 | ||
| Supply Voltages (VDD1, VISO) | VDD1, VISO | -0.5 | 7 | V | Each voltage relative to its respective ground | 11 | |
| Input Voltage (VIA, VIB, RCIN, RCSEL, VSEL), max printed as VDDI + 0.5 V | VIA, VIB, RCIN, RCSEL, VSEL | -0.5 | V | Each voltage relative to its respective ground | 11 | ||
| Output Voltage (VOA, VOB), max printed as VDDO + 0.5 V | VOA, VOB | -0.5 | V | Each voltage relative to its respective ground | 11 | ||
| Average Output Current per Pin | -10 | 10 | mA | 11 | |||
| Common-Mode Transients | -100 | 100 | kV/µs | 11 | |||
| Common-Mode Transient Immunity | /CM/ | 25 | 35 | kV/µs | VIx = VDD1 or VISO, VCM = 1000 V, transient magnitude = 800 V | 4 | |
| Input Currents per Channel | II | -20 | 0.01 | 20 | µA | 0 V ≤ VIx ≤ VDDx | 4 |
| DC-to-DC Converter Setpoint (5 V primary / 5 V secondary) | VISO | 4.7 | 5 | 5.4 | V | IISO = 0 mA | 3 |
| DC-to-DC Converter Setpoint (3.3 V primary / 3.3 V secondary) | VISO | 3 | 3.3 | 3.6 | V | IISO = 0 mA | 5 |
| DC-to-DC Converter Setpoint (5 V primary / 3.3 V secondary) | VISO | 3 | 3.3 | 3.6 | V | IISO = 0 mA | 7 |
| Propagation Delay, C Grade (5 V/5 V) | tPHL, tPLH | 45 | 60 | ns | 50% input to 50% output | 3 | |
| Pulse Width Distortion, C Grade | PWD | 6 | ns | /tPLH − tPHL/ | 3 | ||
| Pulse Width, C Grade | PW | 40 | ns | Within PWD limit | 3 | ||
| Propagation Delay Skew (5 V/5 V), C Grade | tPSK | 15 | ns | Between any two units | 3 | ||
| Propagation Delay Skew (3.3 V/3.3 V), C Grade | tPSK | 45 | ns | Between any two units | 5 | ||
| Codirectional Channel Matching, C Grade | tPSKCD | 6 | ns | 3 | |||
| Opposing Directional Channel Matching, C Grade | tPSKOD | 15 | ns | 3 | |||
| Maximum Data Rate, C Grade | 25 | Mbps | Within PWD limit | 3 | |||
| IC Junction to Ambient Thermal Resistance | θJA | 45 | °C/W | Thermocouple at center of package underside; 4-layer board with thin traces | 9 | ||
| Thermal Shutdown Threshold | TSSD | 150 | °C | TJ rising | 9 | ||
| Thermal Shutdown Hysteresis | TSSD-HYS | 20 | °C | 9 | |||
| Input Capacitance (Input-to-Output) | CI-O | 2.2 | pF | f = 1 MHz | 9 | ||
| Input Capacitance | CI | 4 | pF | Input capacitance from any input data pin to ground | 9 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | pC | In accordance with IEC 60747-5-2 (VDE 0884 Part 2):2003-01, each ADuM520x is proof tested by applying an insulation test voltage ≥ 1590 VPEAK for 1 second (partial discharge detection limit = 5 pC). T | 9 |
CAD (KiCad official)
- Symbol:
ADUM5201CRWZ-RL - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
adum5201crwz-etched.step/adum5201crwz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);adum5201crwz.step/adum5201crwz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
5ae4ecebde77b1fb, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).