Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

INA293B1QDBVRQ1

Texas Instruments · Current-Sensing Amplifiers · SOT-23-5

INA293B1QDBVRQ1 from Texas Instruments, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 OUT output Output voltage of the current sense amplifier, which the absolute maximum ratings limit to GND − 0.3 V to Vs + 0.3 V.
2 GND power_in Ground reference pin for the device, which the datasheet describes as the ground connection with negative common-mode operation down to −4 V.
3 Vs power_in Power supply pin, which operates from a single 2.7 V to 20 V supply with an absolute maximum rating of −0.3 V to 22 V.
4 IN+ input Shunt resistor positive sense input, with an operational common-mode range of −4 V to 110 V and a survival range of −20 V to 120 V.
5 IN- input Shunt resistor negative sense input, with an absolute maximum differential voltage of ±12 V for the INA293B1-Q1 (the ±6 V limit applies only to the B5 gain option).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-23-5
Category Operational Amplifier/Comparator
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (absolute maximum) Vs -0.3 22 V 4
Differential input voltage (VIN+), (VIN-), all variants except A5/B5 -12 12 V 4
Common-mode input voltage (absolute maximum) -20 120 V 4
Operating temperature (absolute maximum) TA -55 150 °C 4
Junction temperature (absolute maximum) TJ 150 °C 4
Storage temperature (absolute maximum) Tstg -65 150 °C 4
Common-mode input range (recommended) VCM -4 48 110 V 5
Operating supply range (recommended) VS 2.7 5 20 V 5
Ambient temperature (recommended) TA -40 125 °C 5
Common-mode input voltage range VCM -4 110 V TA = -40°C to +125°C 5
Common-mode rejection ratio, input referred (DC) CMRR 140 160 dB -4 V ≤ VCM ≤ 110 V, TA = -40°C to +125°C 5
Offset voltage, input referred (INA293x1-Q1) Vos -150 30 150 µV 5
Offset voltage drift (INA293x1-Q1, x2, x3) dVos/dT -0.5 0.05 0.5 µV/℃ TA = -40℃ to +125℃, INA293x1-Q1, INA293x2-Q1, INA293x3-Q1 5
Power supply rejection ratio, input referred (INA293x1-Q1) PSRR -8 1 8 µV/V INA293x1-Q1, 2.7 V ≤ VS ≤ 20 V, TA = -40°C to +125°C 5
Input bias current IB+ IB+ 10 20 30 uA VSENSE = 0 V 5
Input bias current IB- IB- 10 20 30 uA VSENSE = 0 V 5
Gain error GERR -0.15 0.02 0.15 % GND + 50 mV ≤ VOUT ≤ VS, 200 mV 6
Gain drift -10 1 10 ppm/°C TA = -40°C to +125°C 6
Maximum capacitive load 500 pF No sustained oscillations, no isolation resistor 6
Swing to ground 0.005 0.02 V RLOAD = 10 kΩ, VSENSE = 0 V, TA = -40°C to +125°C 6
Supply voltage Vs 2.7 20 V TA = -40°C to +125°C 6
Quiescent current IQ 1.5 2 mA 6
Quiescent current over temperature IQ 2.25 mA TA = -40°C to +125°C 6
Junction-to-ambient thermal resistance (DBV) RθJA 184.7 °C/W 5
Junction-to-case (top) thermal resistance (DBV) RθJC(top) 105.6 °C/W 5
Junction-to-board thermal resistance (DBV) RθJB 47.2 °C/W 5
Junction-to-top characterization parameter (DBV) ΨJT 21.5 °C/W 5
Junction-to-board characterization parameter (DBV) ΨJB 46.9 °C/W 5

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: INA293B1QDBVRQ1
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ina293b1qdbvrq1-etched.step / ina293b1qdbvrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina293b1qdbvrq1.step / ina293b1qdbvrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (31 pp, sha256 d4c7a610b6c57065, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF