Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

RN2025

RENERGY · Energy Metering ICs · LQFP-64(10x10)

RN2025 from RENERGY, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AVCC1 power_in Metering ADC supply input; isolate from AVCC2 with a 10 Ω resistor and decouple with 1 µF in parallel with 0.1 µF.
2 IBN input Current channel B negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1.
3 IBP input Current channel B positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1.
4 IAN input Current channel A negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1.
5 IAP input Current channel A positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1.
6 AVSS1 power_in Analog ground of the internal metering ADC.
7 AVSS2 power_in Analog ground of the self-check (EDT) circuit.
8 UASP_400 output Outputs a 400 µA current-source square wave for phase-A voltage fault detection; if self-check is unused it may float on RN2025A64/B64, but on RN2025C64 it must follow the self-check wiring and WriteUEdtVBCtlReg must be called.
9 RP output Typical output voltage 1.25 V; connect an external 6.2 kΩ resistor to ground, of the same resistor type as the voltage-divider resistors, to set the voltage self-check reference current.
10 P60/SDAIN8/CF0/RTC_OUT bidirectional GPIO P60 multiplexed with GPADC input SDAIN8 (for DC test), CF0 pulse output and RTC_OUT.
11 ISP output Outputs a 2 V square wave for the P side of the current-channel self-check circuit; connect a low-tempco resistor of about 49.9 Ω, and float it if self-check is unused.
12 AVCC2 power_in Self-check circuit supply; decouple with 220 µF in parallel with 10 µF plus 0.1 µF and provide at least 50 mA of supply capability.
13 P44/SDAIN0/TX4/INT6 bidirectional GPIO P44 multiplexed with GPADC input SDAIN0, UART4 TX (cannot be configured as IR-modulated output) and INT6.
14 P45/SDAIN1/RX4/INT7 bidirectional GPIO P45 multiplexed with GPADC input SDAIN1, UART4 RX and INT7.
15 P46/SDAIN2/TX5/KEY6 bidirectional GPIO P46 multiplexed with GPADC input SDAIN2, UART5 TX (cannot be configured as IR-modulated output) and KEY6.
16 P47/SDAIN3/RX5/KEY7/CF4/CF0/RTCOUT bidirectional GPIO P47 multiplexed with GPADC input SDAIN3, UART5 RX, KEY7, CF4, CF0 and RTCOUT.
17 DVCC power_in Digital supply input; decouple with 1 µF plus 0.1 µF and isolate from AVCC2 with a 10 Ω resistor.
18 DGND power_in Digital ground of the internal LDO18 domain.
19 LDO18 power_out Internal 1.8 V LDO output that powers the 1.8 V digital domain; decouple with 1 µF plus 0.1 µF.
20 RSTN input Active-low external reset with an internal pull-up of about 50 kΩ and CMOS input level; a low level longer than 1 ms causes reset.
21 P00/CMP0/INT0/CF2 bidirectional GPIO P00 multiplexed with comparator CMP0 input, INT0 and CF2; the default configuration gives the comparator an internal ~600 kΩ pull-down to ground.
22 P02/CF0/RTCOUT/SDAIN5 bidirectional GPIO P02 with 6 mA drive, multiplexed with CF0 pulse output, RTCOUT (RTC 1 Hz output) and GPADC input SDAIN5.
23 P03/CF1/TCI/TC0_P[0]/RTC_OUT/RTC_1s bidirectional GPIO P03 with 6 mA drive, multiplexed with CF1 pulse output, timer 0 input/output, RTC_OUT and RTC_1S.
24 P06/INT1/SCSN0_1_2 bidirectional GPIO P06 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with INT1 and the SPI0/1/2 chip-select (slave mode only).
25 P07/KEY1/SCLK0_1_2 bidirectional GPIO P07 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with KEY1 and the SPI0/1/2 clock.
26 P10/INT2/MOSI0_1/SDI2 bidirectional GPIO P10 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with INT2 and the SPI MOSI/SDI.
27 P11/KEY2/MISO0_1/SDO2 bidirectional GPIO P11 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with KEY2 and the SPI MISO/SDO.
28 P12/SCSN0_1_2/TCI/TC0_P[0] bidirectional GPIO P12 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI0/1/2 chip-select, timer input and timer 0 output.
29 P13/SCLK0_1_2/TCI/TC0_N[0] bidirectional GPIO P13 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI0/1/2 clock, timer input and timer 0 output.
30 P14/MOSI0_1/SDI2/TCI/TC0_P[1] bidirectional GPIO P14 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MOSI/SDI, timer input and timer 0 output.
31 P15/MISO0_1/SDO2/TCI/TC0_N[1] bidirectional GPIO P15 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MISO/SDO, timer input and timer 0 output.
32 P16/HOSCO/INT3/SCSN3 bidirectional High-frequency crystal output (8.192, 16.384 or 32.768 MHz) multiplexed with GPIO P16, INT3 and SPI3 chip-select; add a 10 MΩ series resistor and two 15-22 pF load capacitors, and select a crystal with load capacitance below 15 pF.
33 P17/HOSCI/INT4/SCLK3 bidirectional High-frequency crystal input multiplexed with GPIO P17, INT4 and SPI3 clock; P16 and P17 select HOSC together.
34 DGND power_in Digital ground.
35 SWDCLK/P20/RX1/RX2/CF3/RTC_1s/TC0_P[1] bidirectional SWD clock multiplexed with GPIO P20, UART1/UART2 RX, CF3, RTC_1S and timer 0 output; SWD pins are pulled up by default after power-up.
36 SWDIO/P21/TX1/TX2/CF2/TC0_P[0]/RTC_OUT bidirectional SWD data multiplexed with GPIO P21, UART1/UART2 TX, CF2, timer 0 output and RTC_OUT; SWD pins are pulled up by default after power-up.
37 P30/ISPEN/TCI/KEY3/CF4/TC1_P[1]/RTC_OUT bidirectional GPIO P30 with 6 mA drive; the BOOTROM samples this pin after reset and enters ISP if it is low, so the application must account for this.
38 P22/RX2/KEY4/MOSI3/TC1_N[0]/CF4 bidirectional GPIO P22 multiplexed with UART2 RX, KEY4, SPI3 MOSI, timer 1 output and CF4.
39 P23/TX2/KEY5/MISO3/TC1_P[0]/RTC_OUT bidirectional GPIO P23 multiplexed with UART2 TX, KEY5, SPI3 MISO, timer 1 output and RTC_OUT.
40 P24/SCL/TCI/TC1_P[0]/SCSN4/CF4 bidirectional GPIO P24 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with I2C SCL, timer input/output, SPI4 chip-select and CF4.
41 P25/SDA/TCI/TC1_P[1]/SCLK4/RTC_OUT bidirectional GPIO P25 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with I2C SDA, timer input/output, SPI4 clock and RTC_OUT.
42 P26/RX3/TCI/TC1_N[0]/CF2/RTC_OUT/MOSI4 bidirectional GPIO P26 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with UART3 RX, timer, CF2, RTC_OUT and SPI4 MOSI.
43 P27/TX3/TCI/TC1_N[1]/CF3/RTC_1s/MISO4 bidirectional GPIO P27 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with UART3 TX, timer, CF3, RTC_1S and SPI4 MISO.
44 P31/SDO2/MISO0_1/SCL/CF4/RTC_OUT bidirectional GPIO P31 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MISO/SDO, I2C SCL, CF4 and RTC_OUT.
45 P32/SDI2/MOSI0_1/SDA/CF3/RTC_1S bidirectional GPIO P32 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MOSI/SDI, I2C SDA, CF3 and RTC_1S.
46 P33/SCLK2/SCLK0_1/RX2/CF2/RTC_OUT/RTC_1S bidirectional GPIO P33 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI clock, UART2 RX, CF2, RTC_OUT and RTC_1S.
47 P34/SCSN2/SCSN0_1/TX2/CF1/RTC_OUT/RTC_1S bidirectional GPIO P34 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI chip-select, UART2 TX, CF1, RTC_OUT and RTC_1S.
48 LXO passive 32.768 kHz passive crystal output; no external resistor or capacitor is needed (on-chip), and it must be guarded from neighbouring signals by ground.
49 LXI passive 32.768 kHz passive crystal input, paired with LXO; no external resistor or capacitor is needed and it must be guarded by ground.
50 BVSS power_in Ground of the VBAT domain.
51 LDO_VBAT power_out VBAT-domain LDO output; requires an external 0.22 µF capacitor.
52 VBAT power_in 3.6 V battery or supercapacitor input that powers only the RTC; it is also the SAR ADC input (two internal 300 kΩ divider resistors, 0.5× gain), and an RC filter of 10 Ω and 1 µF is recommended.
53 VREFB output SAR ADC internal reference output, typically 1.25 V; requires an external 0.22 µF capacitor.
54 P40/KEY6/AIN3 bidirectional VBAT-domain GPIO P40 with KEY6 and SAR ADC input AIN3, which can measure up to 3.6 V at 0.5× PGA; the input-high level must not exceed VBAT.
55 P41/KEY7/AIN2 bidirectional VBAT-domain GPIO P41 with KEY7 and SAR ADC input AIN2; the input range must not exceed 1.25 V (PGA=1), 2.5 V (PGA=0.5) or the supply (PGA=0.2).
56 P42/RTCOUT2/AIN1/SCL/KEY6/RTC_1S bidirectional VBAT-domain GPIO P42 with RTCOUT, SAR ADC input AIN1 (range as P41), I2C SCL, KEY6 and RTC_1S; it is not recommended to connect a battery here because it drives RTCOUT while VBAT alone is powered.
57 P43/AIN0/SDA/KEYOUT bidirectional VBAT-domain GPIO P43 with SAR ADC input AIN0 (range as P41), I2C SDA and KEYOUT, which is a key-event power control output for external EEPROM.
58 P50/AIN4/KEY6/RTC_OUT bidirectional VBAT-domain GPIO P50 with SAR ADC input AIN4 (range as P41), KEY6 and RTC_OUT.
59 P51/AIN5/KEYOUT/RTC_1S bidirectional VBAT-domain GPIO P51 with SAR ADC input AIN5 (range as P41), KEYOUT and RTC_1S.
60 UAN input Voltage channel A negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1.
61 UAP input Voltage channel A positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1.
62 AVSS3 power_in Analog ground of the internal voltage reference.
63 VREFA output ADC reference, typically 1.25 V; requires 0.1 µF and 1 µF external capacitors.
64 LDO3 power_out Metering ADC supply LDO, typically 3 V; requires 0.1 µF and 1 µF external capacitors.

Key specifications

Parameter Value
Manufacturer RENERGY
Package LQFP-64(10x10)
Category ADC/DAC/Data Conversion
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
有功电能测量误差 Err -0.1 0.1 % 8000:1动态范围 30
无功电能测量误差 Err -0.1 0.1 % 8000:1动态范围 30
视在电能测量误差 Err -0.1 0.1 % 8000:1动态范围 30
有效值测量误差 Err -0.2 0.2 % 2000:1动态范围 30
功率测量误差 Err -0.1 0.1 % 2000:1动态范围 30
全失压电流测量误差 -0.5 0.5 % 400:1动态范围 30
最大信号电平(差分, PGA=1) Vxn -1000 1000 mVp PGA=1,差分信号 30
频率测量范围 40 75 Hz 30
电能脉冲输出最大频率 20 KHz 当脉宽低于 84ms 时 30
基准电压输出 Vref 1.25 1.26 1.27 V VCC=3V~5.5V,温度范围:-40℃~+85℃ 30
SAR ADC 输入范围 SAR-IN 0 V 最大值为 BGR(内部低功耗基准,典型值 1.25V) 30
低功耗比较器 LVD 阈值 LVD 2.3 4.9 V LVD 阈值可配置,2.3V 到 4.9V 30
低功耗比较器 CMP0 阈值 Vil1 Vil1 1.23 1.28 1.33 V 默认配置下比较器输出低电平的阈值 30
低功耗比较器 CMP0 阈值 Vil2 Vil2 0.8 0.84 0.88 V 选择0.9V档并且选择有迟滞时 30
VBAT 测量范围 VBAT 0 3.6 5 V SAR ADC 对 VBAT 引脚电压的测量范围 30
输入高频时钟频率范围 HOSI 4.096 16.384 32.768 Mhz 31
内部PLL时钟频率范围 PLL 8.192 16.384 MHz fosc=32.768Khz 31
内部高频RCH(常温) RCH 3 3.2 3.85 MHz 常温,用于芯片复位后默认 31
内部低频RCL RCL 20 32 40 KHz 用于WDT时钟 32
主电源 VCC VCC 2.4 5.5 V 建议主电源选择为3.3V±5%或者5V±5% 32
CPU 最低工作电压 Vil 1.8 1.9 2 V 全温度范围 32
VBAT 供电电压 VBAT1 VBAT1 2.5 3.6 5.5 V RTC 温补电路正常工作,RTC 精度保证的电压工作范围 32
VBAT 供电电压 VBAT2 VBAT2 1.8 3.6 5.5 V RTC 万年历翻转正常,温补电路不保证 32
VBAT 供电功耗(典型) SIdd 1.5 μA 典型条件:Vbat=3.6V;Tc=25度 32
VBAT 供电功耗(极限) SIdd 2 μA 极限条件:Vbat=3.6V;Tc=85度 32
LDO18 内核电压 V1P8 1.62 1.8 1.98 V CPU 内核电压 32
LDO3 Σ-ΔADC 电压 V3 2.85 2.9 2.95 V Σ-ΔADC 电压 32
LDO_VBAT VBAT域数字电压 V2 1.9 2 2.2 V VBAT 域数字电压 32
主电电压 Vvcc -0.3 7 V 32
电池输入电压 Vvbat -0.3 7 V 32
DVDD to DGND -0.3 7 V 32
DVDD to AVDD -0.3 0.3 V 32
电流输入引脚电压 IAP,IAN,IBP,IBN,ICP,ICN,INP,INN -6 6 V 32
电压输入引脚电压 VAP,VAN,VBP,VBN,VCP,VCN -6 6 V 32
数字IO输出低电平 VOL -0.3 V 33
模拟输入电压(相对AGND) VINA -0.3 V 相对于 AGND;上限为 AVDD+0.3(表中为表达式) 33
工作温度范围 TA -40 85 ℃ 33
存储温度范围 Tstg -65 150 ℃ 33
ESD 人体模型 HBM ESD 4000 V HBM,JEDEC EIA/JESD22-A114,所有引脚 33
ESD 机械模型 MM ESD 200 V MM,JEDEC EIA/JESD22-A115C,所有引脚 33
ESD 充电器件模型 CDM ESD 500 V CDM,JEDEC EIA/JESD22-C101F,所有引脚 33
闩锁试验 Latch-up LatchUp 200 mA JEDEC STANDARD NO.78D NOVEMBER 2011,所有引脚 33

CAD (KiCad official)

  • Symbol: RN2025
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: rn2025-etched.step / rn2025-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); rn2025.step / rn2025.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENERGY datasheet (301 pp, sha256 bae190d83688b304, retrieved 2026-11-13, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF