3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMINI52LDE
Nuvoton Tech · Pre-ordered Products · LQFP-48(7x7)
MINI52LDE from Nuvoton Tech, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Not connected. |
| 2 | P1.5 | bidirectional | General purpose digital I/O pin, shared with AIN5 (ADC analog input) and ACMP0_P (analog comparator positive input). |
| 3 | /RESET | input | Schmitt trigger input for hardware reset; a low for 768 clock counts of the internal 22.1184 MHz RC while the system clock is running resets the device, with an internal pull-up allowing power-on reset via an external capacitor to GND. |
| 4 | P3.0 | bidirectional | General purpose digital I/O pin, shared with AIN6 (ADC analog input) and ACMP1_N (analog comparator negative input). |
| 5 | AVSS | power_in | Ground pin for analog circuit. |
| 6 | P5.4 | bidirectional | General purpose digital I/O pin. |
| 7 | P3.1 | bidirectional | General purpose digital I/O pin, shared with AIN7 (ADC analog input) and ACMP1_P (analog comparator positive input). |
| 8 | P3.2 | bidirectional | General purpose digital I/O pin, shared with INT0 (external interrupt 0), STADC (ADC external trigger), T0EX (Timer 0 capture/reset trigger) and ACMP1_P. |
| 9 | P3.4 | bidirectional | General purpose digital I/O pin, shared with T0 (Timer 0 external event counter), SDA (I2C data I/O) and ACMP1_P. |
| 10 | P3.5 | bidirectional | General purpose digital I/O pin, shared with T1 (Timer 1 external event counter), SCL (I2C clock I/O) and ACMP1_P. |
| 11 | NC | unconnected | Not connected. |
| 12 | NC | unconnected | Not connected. |
| 13 | NC | unconnected | Not connected. |
| 14 | P3.6 | bidirectional | General purpose digital I/O pin, shared with ACMP0_O (comparator output), CKO (frequency divider output) and T1EX (Timer 1 capture/reset trigger input). |
| 15 | P5.1 | bidirectional | General purpose digital I/O pin, shared with XTAL2, the output of the internal inverting amplifier that emits the inverted signal of XTAL1. |
| 16 | P5.0 | bidirectional | General purpose digital I/O pin, shared with XTAL1, the input to the internal inverting amplifier; system clock can come from an external crystal or resonator. |
| 17 | VSS | power_in | Ground pin for digital circuit. |
| 18 | LDO_CAP | power_out | LDO output pin. |
| 19 | P5.5 | bidirectional | General purpose digital I/O pin; user program must enable the pull-up resistor in the QFN-33 package. |
| 20 | P5.2 | bidirectional | General purpose digital I/O pin, shared with INT1 (external interrupt 1 input). |
| 21 | NC | unconnected | Not connected. |
| 22 | P2.2 | bidirectional | General purpose digital I/O pin, shared with PWM0 output of PWM unit. |
| 23 | P2.3 | bidirectional | General purpose digital I/O pin, shared with PWM1 output of PWM unit. |
| 24 | P2.4 | bidirectional | General purpose input/output digital pin, shared with PWM2 output of PWM unit. |
| 25 | P2.5 | bidirectional | General purpose digital I/O pin, shared with PWM3 output of PWM unit. |
| 26 | P2.6 | bidirectional | General purpose digital I/O pin, shared with PWM4 output and ACMP1_O (analog comparator output). |
| 27 | NC | unconnected | Not connected. |
| 28 | NC | unconnected | Not connected. |
| 29 | P4.6 | bidirectional | General purpose digital I/O pin, shared with ICE_CLK (serial wired debugger clock input). |
| 30 | P4.7 | bidirectional | General purpose digital I/O pin, shared with ICE_DAT (serial wired debugger data I/O). |
| 31 | NC | unconnected | Not connected. |
| 32 | P0.7 | bidirectional | General purpose digital I/O pin, shared with SPICLK (SPI serial clock I/O). |
| 33 | P0.6 | bidirectional | General purpose digital I/O pin, shared with MISO (SPI master in/slave out). |
| 34 | P0.5 | bidirectional | General purpose digital I/O pin, shared with MOSI (SPI master out/slave in). |
| 35 | P0.4 | bidirectional | General purpose digital I/O pin, shared with SPISS (SPI slave select) and PWM5 output. |
| 36 | NC | unconnected | Not connected. |
| 37 | P0.1 | bidirectional | General purpose digital I/O pin, shared with RTSn (UART RTS output), RX (UART receiver input) and SPISS (SPI slave select). |
| 38 | P0.0 | bidirectional | General purpose digital I/O pin, shared with CTSn (UART CTS input) and TX (UART transmitter output). |
| 39 | NC | unconnected | Not connected. |
| 40 | NC | unconnected | Not connected. |
| 41 | P5.3 | bidirectional | General purpose digital I/O pin, shared with AIN0 (ADC analog input). |
| 42 | VDD | power_in | Power supply for digital circuit. |
| 43 | AVDD | power_in | Power supply for analog circuit. |
| 44 | P1.0 | bidirectional | General purpose digital I/O pin, shared with AIN1 (ADC analog input) and ACMP0_P. |
| 45 | P1.2 | bidirectional | General purpose digital I/O pin, shared with AIN2 (ADC analog input), RX (UART receiver input) and ACMP0_P. |
| 46 | P1.3 | bidirectional | General purpose digital I/O pin, shared with AIN3 (ADC analog input), TX (UART transmitter output) and ACMP0_P. |
| 47 | P1.4 | bidirectional | General purpose digital I/O pin, shared with AIN4 and ACMP0_N (analog comparator negative input). |
| 48 | NC | unconnected | Not connected. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nuvoton Tech |
| Package | LQFP-48(7x7) |
| Category | Solders / Accessories / Batteries |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DC Power Supply | VDD-VSS | -0.3 | 7 | V | 50 | ||
| Input Voltage | VIN | -0.3 | V | min VSS -0.3, max VDD +0.3 | 50 | ||
| Oscillator Frequency | 1/tCLCL | 4 | 24 | MHz | 50 | ||
| Operating Temperature | TA | -40 | 105 | ℃ | 50 | ||
| Storage Temperature | TST | -55 | 150 | ℃ | 50 | ||
| Maximum Current into VDD | IDD | 120 | mA | 50 | |||
| Maximum Current out of VSS | ISS | 120 | mA | 50 | |||
| Maximum Current sunk by an I/O pin | IIO | 35 | mA | 50 | |||
| Maximum Current sourced by an I/O pin | IIO | 35 | mA | 50 | |||
| Maximum Current sunk by total I/O pins | IIO | 100 | mA | 50 | |||
| Maximum Current sourced by total I/O pins | IIO | 100 | mA | 50 | |||
| Operation voltage | VDD | 2.5 | 5.5 | V | VDD = 2.5V ~ 5.5V up to 24 MHz | 50 | |
| Power Ground | VSS / AVSS | -0.3 | V | 50 | |||
| LDO Output Voltage | VLDO | 1.62 | 1.8 | 1.98 | V | VDD ≥ 2.5 V | 50 |
| Band-gap Voltage | VBG | 1.2 | 1.24 | 1.28 | V | VDD = 2.5V ~ 5.5V, TA = 25°C | 50 |
| Band-gap Voltage | VBG | 1.18 | 1.24 | 1.32 | V | VDD = 2.5V ~ 5.5V, TA = -40°C~105°C | 50 |
| Allowed Voltage Difference for VDD and AVDD | VDD-AVDD | -0.3 | 0 | 0.3 | V | - | 50 |
| Logic 1 to 0 Transition Current P0-P5 (Quasi-bidirectional) | ITL | -750 | -690 | µA | VDD = 5.5 V, VIN = 2.0V | 57 | |
| Input Leakage Current P0/1/2/3/4/5 | ILK | -1 | 1 | µA | VDD = 5.5 V, 0 < VIN< VDD, Open-drain or input only mode | 57 | |
| Input Low Voltage P0-P5 (TTL) | VIL1 | -0.3 | 0.8 | V | VDD = 4.5 V | 57 | |
| Input Low Voltage P0-P5 (TTL) | VIL1 | -0.3 | 0.6 | V | VDD = 2.5 V | 57 | |
| Input High Voltage P0-P5 (TTL) | VIH1 | 2 | V | VDD = 5.5 V; max VDD + 0.3 | 57 | ||
| Input High Voltage P0-P5 (TTL) | VIH1 | 1.5 | V | VDD = 3.0 V; max VDD + 0.3 | 57 | ||
| Input Low Voltage XTAL1 | VIL3 | 0 | 0.8 | V | VDD = 4.5 V | 57 | |
| Input Low Voltage XTAL1 | VIL3 | 0 | 0.4 | V | VDD = 2.5 V | 57 | |
| Input High Voltage XTAL1 | VIH3 | 3.5 | V | VDD = 5.5 V; max VDD + 0.3 | 57 | ||
| Input High Voltage XTAL1 | VIH3 | 2.4 | V | VDD = 3.0 V; max VDD + 0.3 | 57 | ||
| Negative-going Threshold /RESET | VILS | -0.3 | 0.2 | V | max printed 0.2VDD | 57 | |
| Positive-going Threshold /RESET | VIHS | 0.7 | V | min printed 0.7 VDD; max VDD + 0.3 | 57 | ||
| Internal /RESET Pin Pull-up Resistor | RRST | 40 | 150 | kΩ | VDD = 2.5 V ~ 5.5V | 57 | |
| Negative-going Threshold P0-P5 Schmitt | VILS | -0.3 | 0.3 | V | max printed 0.3VDD | 57 | |
| Positive-going Threshold P0-P5 Schmitt | VIHS | 0.7 | V | min printed 0.7 VDD; max VDD + 0.3 | 57 | ||
| Source Current Quasi-bidirectional | ISR11 | -300 | -400 | µA | VDD = 4.5 V, VS = 2.4 V | 57 | |
| Source Current Quasi-bidirectional | ISR12 | -50 | -80 | µA | VDD = 2.7 V, VS = 2.2 V | 57 | |
| Source Current Quasi-bidirectional | ISR13 | -40 | -73 | µA | VDD = 2.5 V, VS = 2.0 V | 57 | |
| Source Current Push-pull | ISR21 | -20 | -26 | mA | VDD = 4.5 V, VS = 2.4 V | 57 | |
| Source Current Push-pull | ISR22 | -3 | -5 | mA | VDD = 2.7 V, VS = 2.2 V | 57 | |
| Source Current Push-pull | ISR23 | -2.5 | -5 | mA | VDD = 2.5 V, VS = 2.0 V | 57 | |
| Sink Current | ISK11 | 10 | 15 | mA | VDD = 4.5 V, VS = 0.45 V | 57 | |
| Sink Current | ISK12 | 6 | 9 | mA | VDD = 2.7 V, VS = 0.45 V | 57 | |
| Sink Current | ISK13 | 5 | 8 | mA | VDD = 2.5 V, VS = 0.45 V | 58 | |
| Clock High Time | tCHCX | 10 | ns | 58 | |||
| Clock Low Time | tCLCX | 10 | ns | 58 | |||
| Clock Rise Time | tCLCH | 2 | 15 | ns | 58 | ||
| Clock Fall Time | tCHCL | 2 | 15 | ns | 58 | ||
| HXT Operation Voltage | VHXT | 2.5 | 5.5 | V | 58 | ||
| HXT Temperature | TA | -40 | 105 | ℃ | 58 | ||
| HXT Clock Frequency | fHXT | 4 | 24 | MHz | 58 | ||
| HIRC Supply Voltage | VHRC | 1.62 | 1.8 | 1.98 | V | 59 | |
| HIRC Calibrated Frequency | fHRC | -1 | 1 | % | TA = 25 ℃, VDD = 5 V | 59 | |
| HIRC Calibrated Frequency | fHRC | -2 | 2 | % | TA = -40℃ |
59 | |
| LIRC Supply Voltage | VLRC | 2.5 | 5.5 | V | 60 | ||
| LIRC Oscillator Frequency | fLRC | -10 | 10 | % | VDD=2.5V~ 5.5V, TA = 25℃ | 60 | |
| LIRC Oscillator Frequency | fLRC | -40 | 40 | % | VDD=2.5V~ 5.5V, TA = -40℃~+105℃ | 60 | |
| ADC Resolution | 10 | Bit | 61 | ||||
| ADC Clock Frequency | FADC | 4.2 | MHz | AVDD = 4.5~5.5 V | 61 | ||
| ADC Clock Frequency | FADC | 2.8 | MHz | AVDD =2.5~5.5 V | 61 | ||
| Sample Rate | FS | 300 | kSPS | AVDD = 4.5~5.5 V | 61 | ||
| Sample Rate | FS | 200 | kSPS | AVDD = 2.5~5.5 V | 61 | ||
| ADC Supply Voltage | AVDD | 2.5 | 5.5 | V | 61 | ||
| ADC Analog Input Voltage | VIN | 0 | V | max AVDD | 61 | ||
| LDO DC Power Supply | VDD | 2.5 | 5.5 | V | 62 | ||
| LDO Output Voltage | VLDO | 1.62 | 1.8 | 1.98 | V | 62 | |
| Comparator Supply Voltage | VCMP | 2.5 | 5.5 | V | 64 | ||
| Comparator Operation Current | ICMP | 40 | 80 | μA | AVDD=5V | 64 | |
| Flash Supply Voltage | VFLA | 1.62 | 1.8 | 1.98 | V | 65 | |
| Flash Endurance | NENDUR | 20000 | cycles | 65 | |||
| Flash Data Retention | TRET | 10 | year | TA =85℃ | 65 | ||
| Normal Run Operating Current | IDD1 | 9.2 | mA | VDD 5.5V, HXT 24 MHz, HIRC Disable, All digital modules Enabled | 50 |
CAD (KiCad official)
- Symbol:
MINI52LDE - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
mini52lde-etched.step/mini52lde-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mini52lde.step/mini52lde.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nuvoton Tech datasheet (70 pp, sha256
416d3456a5134048, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).