3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSi14T
Nanjing Zhongke Microelectronics · Touch Sensors · QFN-32(5x5)
Si14T from Nanjing Zhongke Microelectronics, in a QFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IBA | input | Analog input for internal bias adjustment; resistor RB sets the oscillator and internal bias current (RB recommended 100 kΩ to 1500 kΩ, typical 510 kΩ), with CB (typ. 820 pF, max 1.5 nF) to VDD. |
| 2 | SBA | input | Analog input for internal bias adjustment in sleep mode, where RSB sets the sleep power consumption and response time. |
| 3 | TS5 | input | Touch sensor 5 analog input. |
| 4 | TS6 | input | Touch sensor 6 analog input. |
| 5 | TS7 | input | Touch sensor 7 analog input. |
| 6 | TS8 | input | Touch sensor 8 analog input. |
| 7 | TS9 | input | Touch sensor 9 analog input. |
| 8 | SCT | input | Digital input for touch detection suspension control: touch is paused when high, and the chip works normally when low or floating. |
| 9 | TS10 | input | Touch sensor 10 analog input. |
| 10 | VDD | power_in | Listed as VDD (with type 'digital input' in the table); the supply range is 1.8 V to 5.0 V. |
| 11 | TS11 | input | Touch sensor 11 analog input. |
| 12 | TS12 | input | Touch sensor 12 analog input. |
| 13 | TS13 | input | Touch sensor 13 analog input. |
| 14 | N.C. | unconnected | No connection; left floating. |
| 15 | I2C_BA | input | Analog input for internal I2C clock adjustment through resistor RIB; a smaller RIB gives a higher I2C internal clock frequency and more I2C supply current. |
| 16 | RST | input | Digital system reset input, active high. |
| 17 | OUT1 | output | Channel 1 digital output, open drain. |
| 18 | SCL | input | I2C clock digital input. |
| 19 | SDA | bidirectional | I2C data line, digital input/output. |
| 20 | IRQ | output | Interrupt digital output, open drain. |
| 21 | I2C_EN | input | I2C enable digital input, active low. |
| 22 | TS14 | input | Touch sensor 14 analog input. |
| 23 | TS1_SEN0 | input | TS1 sensitivity control bit 0 (digital input); TS1_SEN[2:0]=011 gives register-controlled sensitivity. |
| 24 | TS1_SEN1 | input | TS1 sensitivity control bit 1 (digital input). |
| 25 | TS1_SEN2 | input | TS1 sensitivity control bit 2 (digital input). |
| 26 | VSS | power_in | Ground (VSS); the table lists it as 'digital input' with no further description. |
| 27 | MODE | bidirectional | Output mode control, digital input/output: high selects single channel output, low selects multi-channel output. |
| 28 | VDD | power_in | Power supply, 1.8 V to 5.0 V. |
| 29 | TS1 | input | Touch sensor 1 analog input. |
| 30 | TS2 | input | Touch sensor 2 analog input. |
| 31 | TS3 | input | Touch sensor 3 analog input. |
| 32 | TS4 | input | Touch sensor 4 analog input. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Nanjing Zhongke Microelectronics |
| Package | QFN-32(5x5) |
| Category | Sensors |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating voltage | VDD | 1.8 | 3.3 | 5 | V | 12 | |
| Input induction capacitance range | CS | 10 | 110 | pF | 12 | ||
| Input induction resistance range | RS | 200 | 2000 | Ω | 12 | ||
| Minimum detectable ΔC | ΔC | 0.2 | pF | CS = 10 pF, CDEG = 200 pF (I2C default sensitivity) | 12 | ||
| Recommended offset resistor range | RB | 100 | 510 | 1500 | KΩ | VDD = 3.3 V | 13 |
| Maximum offset capacitance | CB_MAX | 820 | 1500 | pF | 13 | ||
| Recommended synchronous resistance range | RSYNC | 0.91 | 2 | 20 | MΩ | 13 | |
| Battery supply power | 5 | V | 10 | ||||
| Maximum voltage on any pin | 0.3 | V | VDD+0.3 | 10 | |||
| Maximum current on any PAD | 100 | mA | 10 | ||||
| Dissipated power | 800 | mW | 10 | ||||
| Storage temperature | -50 | 150 | ℃ | 10 | |||
| Operating temperature | -20 | 75 | ℃ | 10 | |||
| Junction temperature | 150 | ℃ | 10 | ||||
| Power consumption current | IDD | 68 | µA | VDD = 3.3 V RB = 510 K R_SB=0 | 12 | ||
| Power consumption current | IDD | 145 | µA | VDD = 5.0 V RB = 510 K R_SB=0 | 12 | ||
| Power consumption current non-sensing | IDD | 3.5 | µA | VDD = 3.3 V RB = 510 K R_SB=6 M | 12 | ||
| Power consumption current non-sensing | IDD | 10.5 | µA | VDD = 5.0 V RB = 510 K R_SB=6 M | 12 | ||
| I2C current | IDD_I2C | 0.4 | mA | VDD = 3.3 V RB = 510 K RI2C=20 k | 12 | ||
| I2C current | IDD_I2C | 0.7 | mA | VDD = 5.0 V RB = 510 K RI2C=20 k | 12 | ||
| Output impedance (drain open) | ZO | 71 | Ω | ΔC > 0.2 pF, CS = 10 pF, (I2C default sensitivity) | 13 | ||
| Self-examination time after reset | TCAL | 120 | ms | VDD = 3.3 V RB = 510 K | 13 | ||
| Self-examination time after reset | TCAL | 98 | ms | VDD = 5.0 V RB = 510 K | 13 |
CAD (KiCad official)
- Symbol:
Si14T - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
si14t-etched.step/si14t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si14t.step/si14t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Nanjing Zhongke Microelectronics datasheet (31 pp, sha256
151f9755341ea842, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).