Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

INA310B2QDGKRQ1

Texas Instruments · Current Sense Amplifiers · VSSOP-8

INA310B2QDGKRQ1 from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VS power_in Power supply input, specified for 2.7 V to 20 V.
2 OUT output Analog output voltage; per the electrical characteristics it swings to within (VS) - 150 mV maximum of the supply and to (GND) + 20 mV maximum of ground with a 10 kΩ load.
3 CMPIN input Comparator input, which can take voltage from 0 V up to 5.5 V or up to the supply voltage if that is lower than 5.5 V; the comparator switches at the 0.6 V internal threshold.
4 GND power_in Ground reference for the device.
5 RESET input Comparator reset pin, active low: Low or open selects transparent mode and High selects latch mode, with a voltage range of 0 V to the supply voltage.
6 CMPOUT output Open-drain comparator output that is high when RESET is high in latch mode, and can be pulled up to 0 V to 20 V through a pullup resistor.
7 IN- input Shunt resistor negative sense input; connect to the load side of the sense resistor for high-side applications and to the ground side for low-side applications.
8 IN+ input Shunt resistor positive sense input; connect to the bus-voltage side of the sense resistor for high-side applications and to the load side for low-side applications.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category Amplifiers/Comparators
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Analog inputs differential (VIN+), (VIN-) VIN+, VIN- -12 12 V 4
Analog inputs with respect to GND VIN+, VIN- -20 120 V 4
Supply voltage VS -0.3 22 V 4
Comparator output -0.3 22 V Referenced to GND 4
Input current into any pin 5 mA 4
Operating temperature TA -55 150 °C 4
Junction temperature TJ -65 150 °C 4
Storage temperature Tstg -65 150 °C 4
Common-mode input range VCM -4 48 110 V 4
Operating supply voltage VS 2.7 5 20 V 4
Operating free-air temperature TA -40 125 °C 4
Junction-to-ambient thermal resistance RθJA 172.2 °C/W DGK (VSSOP) 8 pins 4
Junction-to-case (top) thermal resistance RθJC(top) 63.5 °C/W DGK (VSSOP) 8 pins 4
Junction-to-board thermal resistance RθJB 93.8 °C/W DGK (VSSOP) 8 pins 4
Junction-to-top characterization parameter ΨJT 9.8 °C/W DGK (VSSOP) 8 pins 4
Junction-to-board characterization parameter ΨJB 92.2 °C/W DGK (VSSOP) 8 pins 4
Common-mode input range VCM -4 110 V TA = -40°C to +125°C 5
Common-mode rejection ratio CMRR 120 140 dB INA310Bx-Q1, VIN+ = -4 V to 110 V, TA = -40°C to +125°C 5
Common-mode rejection ratio CMRR 65 dB INA310Bx-Q1, f = 50 kHz 5
Offset voltage, RTI VOS -300 55 300 µV 5
Offset drift, RTI dVOS/dT -1 0.1 1 µV/°C TA = -40°C to +125°C, INA310Bx-Q1 5
Power-supply rejection ratio, RTI PSRR -10 1.5 10 µV/V INA310Bx-Q1 2.7 V ≤ VS ≤ 20 V, TA = -40°C to +125°C 5
Input bias current IB 10 20 30 µA IB+, IB-, VSENSE = 0 mV 5
Gain G 50 V/V INA310B2-Q1 5
Gain error GERR -0.5 0.07 0.5 % INA310Bx-Q1, GND + 50 mV ≤ VOUT ≤ VS, 200 mV 5
Gain error drift GERR 2 20 ppm/°C INA310Bx-Q1, TA = -40°C to +125°C 5
Nonlinearity error NLERR -0.01 0.01 % GND + 50 mV ≤ VOUT ≤ VS, 200 mV 5
Maximum capacitive load 500 pF No sustained oscillation, no isolation resistor 5
Swing to GND (relative to GND) VSN 5 20 mV RLOAD = 10 kΩ to GND, TA = -40°C to +125°C, VSENSE = 0 mV 5
Bandwidth BW 1300 kHz INA310B2-Q1, CLOAD = 5 pF, VSENSE = 80mV 6
Slew rate SR 2.5 V/µs Rising edge 6
Settling time to 0.5% tS 10 µs VOUT = 4 V ± 0.1 V step, output settles to 0.5% 6
Settling time to 1% tS 5 µs VOUT = 4 V ± 0.1 V step, output settles to 1% 6
Settling time to 5% tS 1 µs VOUT = 4 V ± 0.1 V step, output settles to 5% 6
Voltage noise density Ven 50 nV/√Hz 6
Alert threshold VTHRESHOLD 585 600 615 mV TA = 25°C 6
Alert threshold VTHRESHOLD 580 620 mV TA = -40°C to +125°C 6
Hysteresis 8 mV TA = 25°C 6
Small-signal propagation delay tP 1 µs Comparator input overdrive = 20 mV 6
Slew-rate-limited propagation delay tP 1.6 µs VOUT step = 0.5 V to 4.5 V, VLIMIT = 4 V 6
Input bias current, CMPIN IBCMPIN -20 1 20 nA TA = 25°C, VCMPIN = 0.4 V to 1.2 V 6
Input bias current, CMPIN IBCMPIN 250 nA TA = -40°C to +125°C, VCMPIN = 0.4 V to 1.2 V 6
High-level leakage current ILKG 1 µA VCMPout = VS 6
Low-level output voltage VOL 300 mV IOL = 2.35 mA 6
Low-level output voltage VOL 350 mV TA = -40°C to +125°C, IOL = 2.35 mA 6
RESET high-level input voltage threshold VIH 1.2 V TA = -40°C to +125°C 6
RESET low-level input voltage threshold VIL 0.4 V TA = -40°C to +125°C 6
Minimum RESET pulse width 100 200 ns TA = -40°C to +125°C 6
RESET propagation delay 250 ns 6
Supply voltage range VS 2.7 20 V TA = -40°C to +125°C 6
Quiescent current IQ 1.6 2 mA 6
Quiescent current IQ 2.25 mA TA = -40°C to +125°C 6

CAD (KiCad official)

  • Symbol: INA310B2QDGKRQ1
  • Footprint: Package_SO:VSSOP-8_3x3mm_P0.65mm
  • 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ina310b2qdgkrq1-etched.step / ina310b2qdgkrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina310b2qdgkrq1.step / ina310b2qdgkrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (35 pp, sha256 cf90218870149e72, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF