3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownOPA818IDRGT
Texas Instruments · FET Input Amplifiers · WSON-8-EP(3x3)
OPA818IDRGT from Texas Instruments, in a WSON-8-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PD | input | Power-down pin: low enables the amplifier and high disables it, with an internal 1 MΩ pullup so the pin can float; the datasheet gives the enable threshold as PD > VS+ - 1 V and the disable threshold as PD < VS+ - 3 V. |
| 2 | FB | output | Optional output feedback resistor connection, internally tied to OUT through metal with limited current capability, so continuous current must stay within the 13 mA feedback-pin rating in Section 6.1. |
| 3 | IN- | input | Inverting input of the amplifier. |
| 4 | IN+ | input | Noninverting input; the typical input common-mode range includes VS- and extends up to 3.2 V below VS+ (3.6 V minimum specified). |
| 5 | VS- | power_in | Negative power supply; the total supply (VS+) - (VS-) must not exceed the 13.5 V absolute maximum rating. |
| 6 | NC | unconnected | No connect; no internal connection to the die. |
| 7 | OUT | output | Amplifier output; output voltage must stay between VS- - 0.5 V and VS+ + 0.5 V, and continuous output current is limited to 25 mA. |
| 8 | VS+ | power_in | Positive power supply; recommended single-supply range is 6 V to 13 V. |
| 9 | Thermal pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-8-EP(3x3) |
| Category | Amplifiers/Comparators |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Open-loop voltage gain | AOL | 85 | 92 | dB | f = dc, VO = ±2 V | 5 | |
| Input offset voltage | VOS | -1.25 | 0.35 | 1.25 | mV | 5 | |
| Input offset voltage over temperature | VOS | -1.8 | 1.8 | mV | TA = -40°C to +85°C | 5 | |
| Input offset voltage drift | -20 | 3 | 20 | µV/°C | TA = -40°C to +85°C | 5 | |
| Input bias current | IB | -25 | 4 | 25 | pA | 5 | |
| Input bias current over temperature | IB | 700 | pA | TA = -40°C to +85°C | 5 | ||
| Input offset current | IOS | -25 | 1 | 25 | pA | 5 | |
| Common-mode rejection ratio | CMRR | 73 | 90 | dB | f = dc, VCM = ±0.5 V | 5 | |
| Common-mode rejection ratio over temperature | CMRR | 70 | dB | f = dc, VCM = ±0.5 V, TA = -40°C to +85°C | 5 | ||
| Internal feedback trace resistance | 0.8 | 1.2 | 1.7 | Ω | DRG package only, device turned off, OUT to FB pin resistance | 5 | |
| ΔVOS at most positive input voltage | ΔVOS | -1 | 0.03 | 1 | mV | VCM = VS+, 3.6 V | 6 |
| ΔVOS at most positive input voltage over temperature | ΔVOS | -1.5 | 1.5 | mV | VCM = VS+, 3.6 V, TA = -40°C to +85°C | 6 | |
| ΔVOS at most negative input voltage | ΔVOS | -1 | 0.23 | 1 | mV | VCM = VS- + 0.25 V | 6 |
| ΔVOS at most negative input voltage over temperature | ΔVOS | -1.5 | 1.5 | mV | VCM = VS- + 0.25 V, TA = -40°C to +85°C | 6 | |
| Linear output drive | IO_MAX | -55 | 55 | mA | VO = ±2.75 V, RL to mid-supply = 50 Ω, [ΔVOS from no-load VOS] ≤ ±1 mV | 6 | |
| Linear output drive over temperature | IO_MAX | -50 | 50 | mA | VO = ±2.5 V, RL to mid-supply = 50 Ω, [ΔVOS from no-load VOS] ≤ ±1 mV, TA = -40°C to +85°C | 6 | |
| Output short-circuit current | ISC | -110 | 110 | mA | 6 | ||
| Single-supply operating range | VS | 6 | 10 | 13 | V | 6 | |
| Quiescent current per channel | IQ | 26.5 | 27.7 | 29 | mA | No load | 6 |
| Quiescent current per channel over temperature | IQ | 23 | 31.5 | mA | No load, TA = -40°C to +85°C | 6 | |
| Positive power supply rejection ratio | PSRR+ | 75 | 95 | dB | ΔVS+ = ±0.25 V | 6 | |
| Positive power supply rejection ratio over temperature | PSRR+ | 70 | dB | ΔVS+ = ±0.25 V, TA = -40°C to +85°C | 6 | ||
| Negative power supply rejection ratio | PSRR- | 80 | 94 | dB | ΔVS- = ±0.25 V | 6 | |
| Negative power supply rejection ratio over temperature | PSRR- | 74 | dB | ΔVS- = ±0.25 V, TA = -40°C to +85°C | 6 | ||
| Power-down quiescent current | IQ (VS+) | 27 | 40 | µA | No load | 6 | |
| PD pin bias current (PD = VS+) | -3 | -2 | µA | No load, PD = VS+ | 6 | ||
| PD pin bias current (PD = VS-) | 13 | 20 | µA | No load, PD = VS- | 6 | ||
| Supply voltage, (VS+), (VS-) | VS | 13.5 | V | 4 | |||
| Differential input voltage | VIN,Diff | -5 | 5 | V | 4 | ||
| Continuous input current | II | -10 | 10 | mA | 4 | ||
| Continuous output current | IO | 25 | mA | 4 | |||
| Continuous current in feedback pin | 13 | mA | 4 | ||||
| Junction temperature | TJ | 125 | °C | 4 | |||
| Operating free-air temperature | TA | -40 | 85 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Single-supply voltage (recommended) | VS | 6 | 10 | 13 | V | 4 | |
| Ambient temperature (recommended) | TA | -40 | 25 | 85 | °C | 4 | |
| Junction-to-ambient thermal resistance (DRG, 8 pins) | RθJA | 54.6 | °C/W | DRG (SON), 8 pins | 4 | ||
| Junction-to-case (top) thermal resistance (DRG, 8 pins) | RθJC(top) | 56 | °C/W | DRG (SON), 8 pins | 4 | ||
| Junction-to-board thermal resistance (DRG, 8 pins) | RθJB | 27.2 | °C/W | DRG (SON), 8 pins | 4 | ||
| Junction-to-top characterization parameter (DRG, 8 pins) | ΨJT | 1.8 | °C/W | DRG (SON), 8 pins | 4 | ||
| Junction-to-board characterization parameter (DRG, 8 pins) | ΨJB | 27.2 | °C/W | DRG (SON), 8 pins | 4 | ||
| Junction-to-case (bottom) thermal resistance (DRG, 8 pins) | RθJC(bot) | 11.1 | °C/W | DRG (SON), 8 pins | 4 |
CAD (KiCad official)
- Symbol:
OPA818IDRGT - Footprint:
Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.6x2.0mm - 3D model: WSON-8-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
opa818idrgt-etched.step/opa818idrgt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);opa818idrgt.step/opa818idrgt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (39 pp, sha256
9a18348cff0586e0, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).