Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LTM8001EY#PBF

Analog Devices · DC-DC Converters · BGA-121

LTM8001EY#PBF from Analog Devices, in a BGA-121. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
A1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
A2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
A3 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
A4 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
A5 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
A6 VIN45 power_in Input to the LDOs on VOUT4 and VOUT5; must be locally bypassed with a low-ESR capacitor, with a 25V absolute maximum rating.
A7 VIN45 power_in Input to the LDOs on VOUT4 and VOUT5; must be locally bypassed with a low-ESR capacitor, with a 25V absolute maximum rating.
A8 BIAS45 power_in Supply pin for the control circuitry of the VOUT4 and VOUT5 LDOs, which must be 1.2V to 1.6V above the output voltage for regulation; absolute maximum rating 25V.
A9 SET5 passive Sets the LDO5 regulation point: a fixed 10µA flows out of this pin through a single resistor (RSET = VOUT/10µA), and absolute current into the pin is limited to ±10mA.
A10 VOUT5 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
A11 VOUT5 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
B1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
B2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
B3 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
B4 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
B5 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
B6 VIN45 power_in Input to the LDOs on VOUT4 and VOUT5; must be locally bypassed with a low-ESR capacitor, with a 25V absolute maximum rating.
B7 VIN45 power_in Input to the LDOs on VOUT4 and VOUT5; must be locally bypassed with a low-ESR capacitor, with a 25V absolute maximum rating.
B8 BIAS123 power_in Supply pin for the control circuitry of the VOUT1-VOUT3 LDOs, which must be 1.2V to 1.6V above the output voltage for regulation; absolute maximum rating 25V.
B9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
B10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
B11 VOUT4 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
C1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
C2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
C3 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
C4 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
C5 VOUT0 power_out Switching regulator output (1.2V to 24V) where the output filter capacitor and load connect between these pins and GND; absolute maximum rating 25V.
C6 VIN45 power_in Input to the LDOs on VOUT4 and VOUT5; must be locally bypassed with a low-ESR capacitor, with a 25V absolute maximum rating.
C7 VIN45 power_in Input to the LDOs on VOUT4 and VOUT5; must be locally bypassed with a low-ESR capacitor, with a 25V absolute maximum rating.
C8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
C9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
C10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
C11 VOUT4 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
D1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D3 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D4 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D7 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
D11 SET4 passive Sets the LDO4 regulation point: a fixed 10µA flows out of this pin through a single resistor (RSET = VOUT/10µA), and absolute current into the pin is limited to ±10mA.
E1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E3 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E4 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E7 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
E11 VOUT3 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
F1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F3 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F4 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F7 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
F11 VOUT3 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
G1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G3 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G4 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G7 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
G11 SET3 passive Sets the LDO3 regulation point: a fixed 10µA flows out of this pin through a single resistor (RSET = VOUT/10µA), and absolute current into the pin is limited to ±10mA.
H1 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H2 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H3 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H4 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H7 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
H11 SET2 passive Sets the LDO2 regulation point: a fixed 10µA flows out of this pin through a single resistor (RSET = VOUT/10µA), and absolute current into the pin is limited to ±10mA.
J1 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
J2 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
J3 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
J4 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J7 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J8 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
J11 VOUT2 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
K1 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
K2 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
K3 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
K4 SS passive Soft-start pin charged by an 11µA current source after enable; an external capacitor to ground limits regulated current during start-up, and the pin is absolute-maximum rated at 6V.
K5 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
K6 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
K7 SYNC input Frequency synchronization input that must be grounded when unused and never left floating; RT should set the internal clock 20% slower than the SYNC pulse frequency, with a 6V absolute maximum rating.
K8 VREF power_out Buffered 2V reference output capable of 0.5mA drive.
K9 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
K10 GND power_in Tie to a local ground plane below the LTM8001 and circuit components; these pads carry most of the module's heat flow, so PCB layout strongly affects thermal performance.
K11 VOUT2 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
L1 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
L2 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
L3 VIN0 power_in Supplies the internal regulator and power switches; must be locally bypassed with a low-ESR capacitor, with a 40V absolute maximum rating.
L4 RUN input Enable pin with no internal pull-up or pull-down; switching stops when the voltage is below about 1.55V, and it may be pulled above 6V through a resistor only if pin current stays under 100µA.
L5 FB0 input Feedback pin regulated to 1.19V, with RFB0 = 11.9kΩ/(VOUT − 1.19V) connected from this pin to ground; absolute maximum rating 3V.
L6 COMP passive Internal PWM comparator compensation pin, generally left open because the LTM8001 is internally compensated; absolute maximum rating 3V.
L7 RT passive Resistor to ground programs the switching frequency and must not be left open; absolute maximum rating 3V.
L8 ILIM input Reduces maximum regulated output current over a 0V to 1.5V control range (voltages above 1.5V have little effect) and should be tied to VREF if unused; absolute maximum rating 3V.
L9 SET1 passive Sets the LDO1 regulation point: a fixed 10µA flows out of this pin through a single resistor (RSET = VOUT/10µA), and absolute current into the pin is limited to ±10mA.
L10 VOUT1 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.
L11 VOUT1 power_out LDO output rated 1.1A that must carry at least 1mA minimum load to regulate and must never see a negative input-to-output voltage.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package BGA-121
Category Power Supply Chip
Pins 121

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum VIN0 Input Voltage 6 V 3
VOUT0 Output DC Voltage 1.2 V 0A < IOUT ≤ 3A, RFB0 Open 3
VOUT0 Output DC Voltage 24 V 0A < IOUT ≤ 3A; RFB0 = 536Ω 3
VOUT0 Output DC Current 0 5 A 6V < VIN0 < 36V, VOUT = 3.3V 3
Quiescent Current Into VIN0 0.1 1 µA RUN = 0V 3
Quiescent Current Into VIN0 26 40 mA No Load 3
VOUT0 Line Regulation -0.5 0.5 % 6V < VIN0 < 36V, IOUT = 1A 3
VOUT0 Load Regulation -1.2 1.2 % VIN0 = 24V, 0A < IOUT < 5A 3
Voltage at FB0 Pin 1.15 1.19 1.21 V 3
RUN Threshold Voltage (Falling) 1.49 1.61 V 3
RUN Threshold Voltage (Rising) 1.63 1.75 V 3
ILIM Control Range 0 1.5 V 3
ILIM Current Limit Accuracy 5.1 6.4 A ILIM = 1.5V 3
ILIM Current Limit Accuracy 2.5 3.4 A ILIM = 0.75V 3
VREF Voltage 1.9 2 2.1 V 0.5mA Load 3
SYNC Input Low Threshold 0.8 V fSYNC = 500kHz 3
SYNC Input High Threshold 1.2 V fSYNC = 500kHz 3
SYNC Input Current -0.1 µA SYNC = 0V 3
SYNC Input Current 0.1 µA SYNC = 2V 3
SET1-5 Pin Current 9.8 10 10.2 µA BIAS123 = BIAS45 = 2V, SETx = 0V, IOUT1-5 = 1mA 3
VOUTx, SETx Offset Voltage -4 4 mV BIAS123 = BIAS45 = 2V, SETx = 0V, IOUT1-5 = 1mA 3
VOUTx, SETx Offset Voltage -6.5 6.5 mV BIAS123 = BIAS45 = 2V, SETx = 0V, IOUT1-5 = 1mA 3
Load Regulation for VOUT1-5 34 52 mV IOUT1-5 = 1mA to 1.1A 3
Minimum Load Current for VOUT1-5 500 µA VOUT0 = VIN45 = BIAS123 = BIAS45 = 10V 3
Minimum Load Current for VOUT1-5 1 mA VOUT0 = VIN45 = BIAS123 = BIAS45 = 22V 3
BIAS123, BIAS45 Dropout Voltage 1.2 V IOUT1-5 = 100mA 3
BIAS123, BIAS45 Dropout Voltage 1.6 V IOUT1-5 = 1.1A 3
VOUT0 to VOUT1-3 and VIN45 to VOUT4-5 Dropout Voltage 100 mV IOUT1-5 = 100mA 3
VOUT0 to VOUT1-3 and VIN45 to VOUT4-5 Dropout Voltage 500 mV IOUT1-5 = 1.1A 3
Maximum VOUT0 to VOUT1-3 and VIN45 to VOUT4-5 Differential Voltage 15 V IOUT1-5 = 310mA 3
Maximum VOUT0 to VOUT1-3 and VIN45 to VOUT4-5 Differential Voltage 22 V IOUT1-5 = 125mA 3
BIAS123, BIAS45 Pin Current 6 mA IOUT1-5 = 100mA 4
BIAS123, BIAS45 Pin Current 30 mA IOUT1-5 = 1.1A 4
VIN0 Input Voltage (operating range) VIN0 6 36 V 1
Operating Junction Temperature Range (LTM8001EY#PBF) -40 125 °C 2
VIN0 Absolute Maximum Voltage VIN0 40 V 2
VIN45, BIAS45 Absolute Maximum Voltage VIN45 25 V 2
BIAS123 Absolute Maximum Voltage BIAS123 25 V 2
FB0, RT, COMP, ILIM, VREF Absolute Maximum Voltage FB0, RT, COMP, ILIM, VREF 3 V 2
VOUT0-5 Absolute Maximum Voltage VOUT0-5 25 V 2
RUN, SYNC, SS Absolute Maximum Voltage RUN, SYNC, SS 6 V 2
SET1-5 Voltage Relative to VOUT1-5 SET1-5 -0.3 0.3 V Relative to VOUT1-5, respectively 2
Current Into SET1-5 SET1-5 -10 10 mA 2
Current Into RUN Pin RUN 100 µA 2
Maximum Junction Temperature 125 °C Notes 2, 3 2
Peak Solder Reflow Body Temperature 245 °C 2
Storage Temperature -55 125 °C 2
Thermal Resistance Junction-to-Ambient θJA 16.1 °C/W Per JESD 51-9, 51-12 2
Thermal Resistance Junction-to-Bottom Case θJCbottom 5.99 °C/W Per JESD 51-9, 51-12 2
Thermal Resistance Junction-to-Top Case θJCtop 13.4 °C/W Per JESD 51-9, 51-12 2
Thermal Resistance Junction-to-Board θJB 4.98 °C/W Per JESD 51-9, 51-12 2

CAD (KiCad official)

  • Symbol: LTM8001EY#PBF
  • Footprint: Package_BGA:BGA-121_9.0x9.0mm_Layout11x11_P0.8mm_Ball0.4mm_Pad0.35mm_NSMD
  • 3D model: BGA-121 (KiCad packages3D, STEP)
  • 3D model files: ltm8001ey-pbf-etched.step / ltm8001ey-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltm8001ey-pbf.step / ltm8001ey-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 772b849c19b80ff3, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF