Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MX25V1006FZUI

MXIC(Macronix) · Pre-ordered Products · USON-8

MX25V1006FZUI from MXIC(Macronix), in a USON-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS# input Chip Select input that enables serial access to the device; when high the device is in standby mode.
2 SO/SIO1 bidirectional Serial Data Output for 1 x I/O, or Serial Data Input & Output for Dual output mode.
3 WP# input Write Protection input; it stays internally pulled up when not physically connected, and the pull-up is disabled if connected.
4 GND power_in Ground.
5 SI/SIO0 bidirectional Serial Data Input for 1 x I/O, or Serial Data Input & Output for Dual output mode.
6 SCLK input Serial clock input.
7 NC unconnected No connect pin.
8 VCC power_in +3.3V power supply, with a voltage range of 2.3V to 3.6V.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer MXIC(Macronix)
Package USON-8
Category Electronic Tools/Instruments/Consumables
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Load Current ILI -2 0.02 2 uA VCC = VCC Max; VIN = VCC or GND 42
Output Leakage Current ILO -2 0.02 2 uA VCC = VCC Max; VOUT = VCC or GND 42
VCC Standby Current ISB1 5 25 uA VIN = VCC or GND; CS#=VCC 42
VCC Read ICC1 6 mA f=50MHz; SCLK=0.1VCC/0.9VCC; SO=Open 42
VCC Program Current (PP) ICC2 5 20 mA Program in Progress; CS#=VCC 42
VCC Write Status Register (WRSR) Current ICC3 2.1 15 mA Program status register in progress; CS#=VCC 42
VCC Sector Erase Current (SE) ICC4 5 15 mA Erase in Progress; CS#=VCC 42
VCC Chip Erase Current (CE) ICC5 5 20 mA Erase in Progress; CS#=VCC 42
Output Low Voltage VOL 0.4 V IOL = 1.6mA 42
Low VCC Write Inhibit Voltage VWI 1.5 2.1 V 42
Deep Power-down Current ISB2 10 uA VIN = VCC or GND; CS#=VCC 42
Input Capacitance CIN 6 pF VIN = 0V 40
Output Capacitance COUT 8 pF VOUT = 0V 40
Clock Frequency (fast-read, PP, SE, BE, CE, DP, RES, RDP, WREN, WRDI, RDID, RDSR, WRSR) fSCLK 80 MHz 2.7-3.6V 43
Clock Frequency (fast-read, PP, SE, BE, CE, DP, RES, RDP, WREN, WRDI, RDID, RDSR, WRSR) fSCLK 50 MHz 2.3-2.7V 43
Clock Frequency for READ instructions fRSCLK 33 MHz 43
Clock Frequency for DREAD instructions fTSCLK 80 MHz 2.7-3.6V 43
Clock Frequency for DREAD instructions fTSCLK 50 MHz 2.3-2.7V 43
Clock High Time tCH 13 ns Normal Read (fRSCLK) 43
Clock Low Time tCL 13 ns Normal Read (fRSCLK) 43
CS# Active Setup Time (relative to SCLK) tSLCH 7 ns 43
CS# Not Active Hold Time (relative to SCLK) tCHSL 7 ns 43
Data In Setup Time tDVCH 2 ns 43
Data In Hold Time tCHDX 5 ns 43
CS# Active Hold Time (relative to SCLK) tCHSH 7 ns 43
CS# Not Active Setup Time (relative to SCLK) tSHCH 7 ns 43
CS# Deselect Time tSHSL 20 ns From Read to next Read 43
CS# Deselect Time tSHSL 40 ns From Write/Erase/Program to Read Status Register 43
Output Disable Time tSHQZ 6 ns 43
Clock Low to Output Valid tCLQV 8 ns Loading: 30pF 43
Clock Low to Output Valid tCLQV 6 ns Loading: 15pF 43
Output Hold Time tCLQX 0 ns 43
Write Protect Setup Time tWHSL 20 ns 43
Write Protect Hold Time tSHWL 100 ns 43
CS# High to Deep Power-down Mode tDP 10 us 43
CS# High to Standby Mode without Electronic Signature Read tRES1 8.8 us 43
CS# High to Standby Mode with Electronic Signature Read tRES2 8.8 us 43
Write Status Register Cycle Time tW 5 40 ms 43
Byte-Program Cycle Time tBP 20 50 us 43
Page Program Cycle Time tPP 1.6 10 ms 43
Sector Erase Cycle Time tSE 50 500 ms 43
Block Erase Cycle Time (32K) tBE32 0.3 3.8 s 43
Block Erase Cycle Time (64K) tBE 0.6 4 s 43
Chip Erase Cycle Time tCE 1.8 6.8 s 43
VCC Rise Time tVR 500000 us/V 45
VCC voltage needed to below VPWD for ensuring initialization VPWD 0.9 V 47
Minimum duration VCC below VPWD for ensuring initialization tPWD 300 us 47
VCC(min.) to device operation tVSL 800 us 47
Ambient Operating Temperature -40 85 °C 40
Storage Temperature -65 150 °C 40
VCC to Ground Potential VCC -0.5 4 V 40
Latch-up current -100 100 mA Includes all pins except VCC; VCC=2.5V, one pin at a time 48
Data retention 20 years 55°C 48
Erase/Program Cycle 100000 cycles 48

CAD (KiCad official)

  • Symbol: MX25V1006FZUI
  • Footprint: Package_SON:SON-8-1EP_3x2mm_P0.5mm_EP1.4x1.6mm
  • 3D model: USON-8 (KiCad packages3D, STEP)
  • 3D model files: mx25v1006fzui-etched.step / mx25v1006fzui-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mx25v1006fzui.step / mx25v1006fzui.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MXIC(Macronix) datasheet (55 pp, sha256 02fe534c9a6c6c64, retrieved 2026-11-08, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF