Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

M24C64-DRMN8TP

The maker sells this part only as M24C64-DRMN8TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 16, p.39)). The DigiKey and Mouser numbers on this page are for M24C64-DRMN8TP/K.

STMicroelectronics · EEPROM · SOP-8

M24C64-DRMN8TP from STMicroelectronics, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E0 input Chip Enable input that sets the least significant bit of the 7-bit device select code; must be tied to VCC or VSS, and is read as low (0) when left floating.
2 E1 input Chip Enable input that sets the middle bit of the 3-bit chip enable address in the device select code; must be tied to VCC or VSS, and is read as low (0) when left floating.
3 E2 input Chip Enable input that sets the most significant bit of the 3-bit chip enable address in the device select code; must be tied to VCC or VSS, and is read as low (0) when left floating.
4 VSS power_in Ground, the reference for the VCC supply voltage.
5 SDA bidirectional Serial Data input/output with an open-drain output that may be wire-OR'ed on the bus; requires a pull-up resistor to VCC.
6 SCL input Serial Clock input used to strobe data into SDA and to output data on SDA.
7 WC input Write Control input: write operations to the entire memory array are disabled when driven high, and enabled when driven low or left floating.
8 VCC power_in Supply voltage pin, operating range 1.7 V to 5.5 V, with a 10 nF to 100 nF decoupling capacitor recommended close to the VCC/VSS pins.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (voltage range R) VCC 1.7 5.5 V 27
Ambient operating temperature (grade 8) TA -40 105 °C 27
Ambient operating temperature -40 130 °C 26
Storage temperature TSTG -65 150 °C 26
Input or output range VIO -0.5 6.5 V 26
DC output current IOL 5 mA SDA = 0 26
Supply voltage VCC -0.5 6.5 V 26
Electrostatic pulse (Human Body model) VESD 4000 V Human Body model, AEC-Q100-002 26
Write cycle endurance Ncycle 4e+06 TA ≤ 25 °C, 1.7 V < VCC < 5.5 V 27
Write cycle endurance Ncycle 1.2e+06 TA = 85 °C, 1.7 V < VCC < 5.5 V 27
Write cycle endurance Ncycle 900000 TA = 105 °C, 1.7 V < VCC < 5.5 V 27
Input capacitance (SDA) CIN 8 pF 28
Input impedance (E2, E1, E0, WC) ZL 30 kΩ VIN < 0.3 VCC 28
Input impedance (E2, E1, E0, WC) ZH 500 kΩ VIN > 0.7 VCC 28
Load capacitance Cbus 100 pF 27
Input leakage current (SCL, SDA, E2, E1, E0) ILI -2 2 µA VIN = VSS or VCC, device in Standby mode 29
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 29
Supply current (Read) ICC 2 mA fC = 400 kHz, VCC = 5.5 V 29
Supply current (Read) ICC 1 mA fC = 400 kHz, VCC = 1.7 V 29
Supply current (Write) ICC0 2 mA During tW 29
Standby supply current ICC1 1 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 2 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V 29
Standby supply current ICC1 3 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Standby supply current ICC1 2.5 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 5 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Input low voltage (SCL, SDA, WC) VIL -0.45 0.3 V 29
Input high voltage (SCL, SDA) VIH 0.7 6.5 V 29
Input high voltage (WC, E2, E1, E0) VIH 0.7 0.6 V 29
Output low voltage VOL 0.4 V IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V 29
Output low voltage VOL 0.3 V IOL = 1 mA, VCC = 1.7 V 29
Clock frequency (400 kHz) fC 400 kHz 400 kHz AC characteristics 30
Clock pulse width high (400 kHz) tCHCL 600 ns 400 kHz AC characteristics 30
Clock pulse width low (400 kHz) tCLCH 1300 ns 400 kHz AC characteristics 30
SDA (out) fall time (400 kHz) tQL1QL2 20 120 ns CL = 10 pF 30
Data in setup time (400 kHz) tDXCH 100 ns 400 kHz AC characteristics 30
Data in hold time (400 kHz) tCLDX 0 ns 400 kHz AC characteristics 30
Data out hold time (400 kHz) tCLQX 100 ns 400 kHz AC characteristics 30
Clock low to next data valid (access time, 400 kHz) tAA 900 ns 400 kHz AC characteristics 30
Start condition setup time (400 kHz) tCHDL 600 ns 400 kHz AC characteristics 30
Start condition hold time (400 kHz) tDLCL 600 ns 400 kHz AC characteristics 30
Stop condition setup time (400 kHz) tCHDH 600 ns 400 kHz AC characteristics 30
Time between Stop and next Start (400 kHz) tDHDL 1300 ns 400 kHz AC characteristics 30
WC set up time (before the Start condition, 400 kHz) tWLDL 0 µs WC=0 set up time condition to enable the execution of a WRITE command 30
WC hold time (after the Stop condition, 400 kHz) tDHWH 1 µs WC=0 hold time condition to enable the execution of a WRITE command 30
Write time (400 kHz) tW 4 ms 30
Pulse width ignored (input filter on SCL and SDA, 400 kHz) tNS 80 ns Single glitch 30
Clock frequency (1 MHz) fC 0 1 MHz 1 MHz AC characteristics 31
Clock pulse width high (1 MHz) tCHCL 260 ns 1 MHz AC characteristics 31
Clock pulse width low (1 MHz) tCLCH 400 ns 1 MHz AC characteristics 31
SDA (out) fall time (1 MHz) tQL1QL2 120 ns Characterized only, not tested in production 31
Data in setup time (1 MHz) tDXCH 50 ns 1 MHz AC characteristics 31
Clock low to next data valid (access time, 1 MHz) tAA 450 ns 1 MHz AC characteristics 31
Start condition setup time (1 MHz) tCHDL 250 ns 1 MHz AC characteristics 31
Stop condition setup time (1 MHz) tCHDH 250 ns 1 MHz AC characteristics 31
Time between Stop and next Start (1 MHz) tDHDL 500 ns 1 MHz AC characteristics 31

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST 26

CAD (KiCad official)

  • Symbol: M24C64-DRMN8TP
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: m24c64-drmn8tp-etched.step / m24c64-drmn8tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24c64-drmn8tp.step / m24c64-drmn8tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (42 pp, sha256 672dc8f58af2d187, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF