Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ISL6353IRTZ

RENESAS · Power Management Specialized - PMIC · TQFN-40-EP(5x5)

ISL6353IRTZ from RENESAS, in a TQFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SDA bidirectional Serial communication bus data signal connected between the CPU and the voltage regulator.
2 ALERT# output Serial communication bus alert signal connected between the CPU and the voltage regulator; ALERT# is specified as an open-drain output with a 7V maximum rating.
3 SCLK input Serial communication bus clock signal connected between the CPU and the voltage regulator.
4 VR_ON input Voltage regulator enable input; a high level logic signal on this pin enables the VR.
5 PGOOD output Open-drain output indicating the regulator is ready to supply regulated voltage; requires an external pull-up resistor.
6 IMON output Sources a current proportional to the regulator output current; a resistor to ground sets a voltage that is sampled by an internal ADC.
7 VR_HOT# output Thermal overload output indicator (open-drain output per the absolute maximum ratings, 7V maximum).
8 NTC input Thermistor input to the VR_HOT# circuit.
9 VW passive Window voltage set pin; a resistor from this pin to COMP programs the switching frequency (18k gives approximately 300kHz).
10 COMP output Output of the error amplifier.
11 FB input Inverting input of the error amplifier.
12 FB2 passive Switches an RC network from VOUT to FB in PS1 and PS2 modes to improve transient performance and phase margin; the pin can be left open if the function is not needed.
13 ISEN3 input Individual current sensing input for Phase 3; leave open when configured for 2-phase operation.
14 ISEN2 input Individual current sensing input for Phase 2; pulling this pin to 5V VDD disables Phase 2 and runs the controller in 1-phase mode.
15 ISEN1 input Individual current sensing input for Phase 1.
16 VSEN input Output voltage sense pin; connect to the output voltage (typically VDDQ) at the desired remote voltage sensing location.
17 RTN input Output voltage sense return pin; connect to ground at the desired remote sensing location.
18 ISUMN input Inverting input of the transconductance amplifier used for current monitoring and overcurrent protection.
19 ISUMP input Non-inverting input of the transconductance amplifier used for current monitoring and overcurrent protection.
20 VDD power_in 5V bias power; the recommended supply is +5V ±5%.
21 VIN power_in Input supply voltage used for input supply feed-forward compensation; recommended input voltage range is 4.5V to 25V.
22 PROG1 input Program pin for the IMAX setting, selected by resistor per Table 6.
23 BOOT1 passive Connect an MLCC capacitor across BOOT1 and PH1; the boot capacitor is charged through an internal switch from VDDP.
24 UG1 output Output of the Phase 1 high-side MOSFET gate driver; connect to the gate of the Phase 1 high-side MOSFET.
25 PH1 passive Current return path for the Phase 1 high-side gate driver; connect to the node of the high-side source, low-side drain and Phase 1 output inductor.
26 GND power_in Electrical ground connection for the IC; connect to the PCB ground plane next to the controller or to the exposed pad via a low impedance path.
27 LG1 output Output of the Phase 1 low-side MOSFET gate driver; connect to the gate of the Phase 1 low-side MOSFET.
28 PWM3 output PWM output for Phase 3; pulling this pin to 5V VDD disables Phase 3 and lets the other phases operate.
29 VDDP power_in Input bias for the internal gate drivers; connect +5V and decouple with at least 1µF MLCC close to the IC.
30 LG2 output Output of the Phase 2 low-side MOSFET gate driver; connect to the gate of the Phase 2 low-side MOSFET.
31 GND power_in Electrical ground connection for the IC; connect to the PCB ground plane next to the controller or to the exposed pad via a low impedance path.
32 PH2 passive Current return path for the Phase 2 high-side gate driver; connect to the node of the high-side source, low-side drain and Phase 2 output inductor.
33 UG2 output Output of the Phase 2 high-side MOSFET gate driver; connect to the gate of the Phase 2 high-side MOSFET.
34 BOOT2 passive Connect an MLCC capacitor across BOOT2 and PH2; the boot capacitor is charged through an internal switch from VDDP.
35 PROG2 input Program pin for VBOOT voltage, droop enable/disable and the number of active phases in PS1 mode, per Table 7.
36 PSI input External power-state pin: ground selects the SVID register power state, high impedance selects PS1, and logic high selects PS2.
37 VSET2 input Logic input used with VSET1 to program the output voltage with external signals, per Table 9.
38 VSET1 input Logic input used with VSET2 to program the output voltage with external signals, per Table 9.
39 OVP output Inverter output that latches high for an overvoltage event and is reset by POR.
40 ADDR input Sets the SVID address offset register, range 0 to 13 (0h to Dh) by resistor per Table 8.
41 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package TQFN-40-EP(5x5)
Category Power Management
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
+5V supply current (VR_ON = 1V) IVDD 4 4 4.6 mA VR_ON = 1V 8
Power-on-reset threshold, VDD rising PORr 4.35 4.5 V VDD rising 8
Power-on-reset threshold, VDD falling PORf 4 4.15 V VDD falling 8
Power-on-reset threshold, VIN rising PORr 4 4.35 V VIN pin rising 8
Power-on-reset threshold, VIN falling PORf 2.8 3.5 V VIN pin falling 8
System accuracy %Error (VCC_CORE), IRTZ %Error (VCC_CORE) -0.8 0.8 % No load; closed loop, active mode range; VID = 0.75V to 1.50V 8
System accuracy (VCC_CORE), IRTZ %Error (VCC_CORE) -10 10 mV No load; closed loop, active mode range; VID = 0.5V to 0.7375V 8
System accuracy (VCC_CORE), IRTZ %Error (VCC_CORE) -18 18 mV No load; closed loop, active mode range; VID = 0.3V to 0.4875V 8
Maximum output voltage + offset VCC_CORE(max) 2.155 V VID = FFh, OFFSET = 7Fh 8
Minimum output voltage VCC_CORE(min) 0.25 V VID = 01h, OFFSET = 00h 8
Nominal channel frequency fSW(nom) 280 300 320 kHz RFSET = 18kΩ, 3-channel operation, VCOMP = 1V 9
Adjustment range (channel frequency) 200 500 kHz 9
Current-sense amplifier input offset -0.1 0.1 mV IFB = 0A 9
PGOOD low voltage VOL 0.26 0.4 V IPGOOD = 4mA 9
PGOOD leakage current IOH -1 1 µA PGOOD = 3.3V 9
ALERT# pull-down resistance 7 13 Ω 9
UGATE pull-up resistance RUGPU 1 1.5 Ω 200mA source current 9
UGATE sink resistance RUGPD 1 1.5 Ω 250mA sink current 9
LGATE pull-up resistance RLGPU 1 1.5 Ω 250mA source current 9
LGATE sink resistance RLGPD 0.5 0.9 Ω 250mA sink current 9
Pre-charge overvoltage threshold OVP 2.29 2.35 V VSEN rising above setpoint for >1ms 9
Overvoltage threshold OVH 145 175 200 mV VSEN rising above setpoint for >1ms 9
Overcurrent threshold, IRTZ 3/2/1-phase PS0 54.5 60 64.5 µA IRTZ 3/2/1-Phase Config, PS0 9
Overcurrent threshold, IRTZ 3-phase PS1 drop to 2-phase 37 40 43.2 µA IRTZ 3-Phase Config, PS1 - Drop to 2-Phase 9
Overcurrent threshold, IRTZ 3-phase PS1/2 drop to 1-phase 18.5 20 22.25 µA IRTZ 3-Phase Config, PS1/2 - Drop to 1-Phase 9
Overcurrent threshold, IRTZ 2-phase PS1/2 drop to 1-phase 27 30 33 µA IRTZ 2-Phase Config, PS1/2 - Drop to 1-Phase 9
Way overcurrent threshold, IRTZ 3/2/1-phase PS0 74 88 100 µA IRTZ 3/2/1-Phase Config, PS0 10
Way overcurrent threshold, IRTZ 3-phase PS1 drop to 2-phase 50 60 68 µA IRTZ 3-Phase Config, PS1 - Drop to 2-Phase 10
Way overcurrent threshold, IRTZ 3-phase PS1/2 drop to 1-phase 27 32 35.8 µA IRTZ 3-Phase Config, PS1/2 - Drop to 1-Phase 10
NTC source current, IRTZ 56 60 62 µA NTC = 1.3V 10
VR_HOT# trip voltage 0.895 0.91 V Falling 10
ALERT# trip voltage 0.915 0.93 V Falling 10
IMON output current IIMON 12.3 12.45 12.6 µA ISUM- pin current = 50µA 10
IccMAX alert trip voltage VIMONMAX 1.2 1.225 V Rising 10
IccMAX alert reset voltage 1.05 1.14 V Falling 10
VR_ON input low VIL_MAX 0.3 V 10
VR_ON input high VIH_MIN 0.8 V 10
VSET1/2 input low VSETIL_MAX 1.5 V 10
VSET1/2 input high VSETIH_MIN 3.1 V 10
PSI sink/source current 12 16 20 µA PSI Voltage 10
PSI pin state PS0 0 0.51 V PS0, VDD = 5V 10
PWM3 output low VOL_MAX 1 V Sinking 5mA 10
PWM3 output high VOH_MIN 3.5 V Sourcing 5mA 10
Supply voltage, VDD VDD 5 V +5V ±5% 8
Supply voltage tolerance, VDD -5 5 % VDD = +5V ±5% 8
Input supply voltage, VIN VIN 4.5 25 V 8
Ambient temperature, ISL6353IRTZ TA -40 85 °C ISL6353IRTZ 8
Junction temperature, ISL6353IRTZ TJ -40 125 °C ISL6353IRTZ 8
Supply voltage, VDD VDD -0.3 7 V 8
Input supply voltage, VIN VIN 28 V 8
Boot voltage BOOT -0.3 33 V 8
Boot to phase voltage (DC) BOOT-PHASE -0.3 7 V DC 8
Phase voltage PHASE -7 V <20ns pulse width, 10µJ 8
LGATE voltage (DC) LGATE -0.3 V DC; maximum VDD + 0.3V 8
All other pins voltage -0.3 V Maximum VDD + 0.3V 8
Open drain outputs PGOOD, VR_HOT#, ALERT# -0.3 7 V 8
Maximum junction temperature TJ 150 °C 8
Maximum storage temperature range TSTG -65 150 °C 8
Thermal resistance junction-to-ambient, 40 Ld TQFN θJA 32 °C/W Free air, high effective thermal conductivity test board (Notes 4, 5) 8
Thermal resistance junction-to-case, 40 Ld TQFN θJC 3 °C/W Case = center of exposed metal pad (Note 5) 8

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper near this trace. Recommend routing the PH1 trace to the phase 1 high-side MOSFET source pins instead of general copper. 29

CAD (KiCad official)

  • Symbol: ISL6353IRTZ
  • Footprint: Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm
  • 3D model: TQFN-40-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: isl6353irtz-etched.step / isl6353irtz-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl6353irtz.step / isl6353irtz.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (30 pp, sha256 3d503073f071ea00, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF