Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT1762EMS8#TRPBF

Analog Devices · Linear Voltage Regulators (LDO) · MSOP-8

LT1762EMS8#TRPBF from Analog Devices, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT power_out Output supplies power to the load, and a minimum output capacitor of 2.2µF is required to prevent oscillations.
2 SENSE/ADJ input For the adjustable LT1762 this is the ADJ error-amplifier input, clamped to ±7V with a 30nA bias current, setting the output from 1.22V to 20V; for fixed versions it is the SENSE input, best connected to OUT for optimum regulation.
3 BYP passive Bypass pin clamped internally to ±0.6V; a maximum 0.01µF capacitor from the output reduces noise to a typical 20µVRMS over 10Hz to 100kHz, and it must be left unconnected if not used.
4 GND power_in Ground reference pin for the regulator.
5 SHDN input Shutdown input that turns the output off when pulled low, can be driven by 5V logic or open-collector logic with a pull-up resistor, and must be connected to VIN if unused.
6 NC unconnected No connection.
7 NC unconnected No connection.
8 IN power_in Input supply pin for the regulator, which is reverse-battery protected and should have a 1µF to 10µF bypass capacitor when more than six inches from the main input filter capacitor.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Regulated Output Voltage (ADJ pin, VIN = 2V, ILOAD = 1mA) 1.208 1.22 1.232 V VIN = 2V, ILOAD = 1mA 3
ADJ Pin Voltage (Regulated Output Voltage, l) 1.19 1.22 1.25 V 2.22V < VIN < 20V, 1mA < ILOAD < 150mA, l = full operating temperature range 3
Line Regulation (LT1762 adjustable) 1 5 mV ΔVIN = 2V to 20V, ILOAD = 1mA, l 3
Load Regulation (LT1762 adjustable) 1 6 mV VIN = 2.22V, ΔILOAD = 1mA to 150mA 3
Load Regulation (LT1762 adjustable, l) 15 mV VIN = 2.22V, ΔILOAD = 1mA to 150mA, l = full operating temperature range 3
Minimum Operating Voltage 1.8 2.3 V ILOAD = 150mA, l 3
Dropout Voltage 0.09 0.15 V VIN = VOUT(NOMINAL), ILOAD = 1mA 3
Dropout Voltage 0.19 V VIN = VOUT(NOMINAL), ILOAD = 1mA, l 3
Dropout Voltage 0.15 0.21 V VIN = VOUT(NOMINAL), ILOAD = 10mA 3
Dropout Voltage 0.25 V VIN = VOUT(NOMINAL), ILOAD = 10mA, l 3
Dropout Voltage 0.21 0.27 V VIN = VOUT(NOMINAL), ILOAD = 50mA 3
Dropout Voltage 0.31 V VIN = VOUT(NOMINAL), ILOAD = 50mA, l 3
Dropout Voltage 0.27 0.33 V VIN = VOUT(NOMINAL), ILOAD = 150mA 3
Dropout Voltage 0.4 V VIN = VOUT(NOMINAL), ILOAD = 150mA, l 3
GND Pin Current 25 65 µA VIN = VOUT(NOMINAL), ILOAD = 0mA, l 3
GND Pin Current 70 120 µA VIN = VOUT(NOMINAL), ILOAD = 1mA, l 3
GND Pin Current 350 500 µA VIN = VOUT(NOMINAL), ILOAD = 10mA, l 3
GND Pin Current 1.3 1.8 mA VIN = VOUT(NOMINAL), ILOAD = 50mA, l 3
GND Pin Current 4 7 mA VIN = VOUT(NOMINAL), ILOAD = 150mA, l 3
Current Limit (l) 160 mA VIN = VOUT(NOMINAL) + 1V, ΔVOUT = -0.1V, l 4
Current Limit 400 mA VIN = 7V, VOUT = 0V 4
ADJ Pin Bias Current IADJ 30 100 nA Notes 3, 8 4
Shutdown Threshold (VOUT Off to On, l) 0.8 2 V VOUT = Off to On, l 4
Shutdown Threshold (VOUT On to Off, l) 0.25 0.65 V VOUT = On to Off, l 4
Quiescent Current in Shutdown 0.1 1 µA VIN = 6V, VSHDN = 0V 4
Ripple Rejection 50 65 dB VIN, VOUT = 1V (Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 150mA 4
Input Reverse Leakage Current 1 mA VIN = -20V, VOUT = 0V, l 4
Reverse Output Current (LT1762 adjustable) 5 10 µA VOUT = 1.22V, VIN < 1.22V (Note 3) 4
Output Voltage Noise 20 µVRMS COUT = 10µF, CBYP = 0.01µF, ILOAD = 150mA, BW = 10Hz to 100kHz 4
SHDN Pin Current 0.1 µA VSHDN = 0V 4
SHDN Pin Current 1 µA VSHDN = 20V 4
IN Pin Voltage -20 20 V 2
OUT Pin Voltage -20 20 V 2
Input to Output Differential Voltage -20 20 V 2
SENSE Pin Voltage -20 20 V 2
ADJ Pin Voltage -7 7 V 2
BYP Pin Voltage -0.6 0.6 V 2
SHDN Pin Voltage -20 20 V 2
Operating Junction Temperature Range TJ -40 125 °C Note 2 2
Storage Temperature Range -65 150 °C 2
Junction-to-Ambient Thermal Resistance (MS8) θJA 125 °C/W MS8 package, as printed in pin configuration 2
Junction-to-Ambient Thermal Resistance (measured range) θJA 110 140 °C/W Measured on 3/32" FR-4, 1 oz copper, still air; varies with copper area (Table 1) 14
Maximum Junction Temperature TJMAX 150 °C Printed in pin configuration header 2

CAD (KiCad official)

  • Symbol: LT1762EMS8#TRPBF
  • Footprint: Package_SO:MSOP-8_3x3mm_P0.65mm
  • 3D model: MSOP-8 (KiCad packages3D, STEP)
  • 3D model files: lt1762ems8-trpbf-etched.step / lt1762ems8-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt1762ems8-trpbf.step / lt1762ems8-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (18 pp, sha256 74e2ca01c993d790, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF