component
FAN53745UC00X
Public Made by Adomby adom
onsemi DC-DC Converters, WLCSP-6(1.38x0.94). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFAN53745UC00X
onsemi · DC-DC Converters · WLCSP-6(1.38x0.94)
FAN53745UC00X from onsemi, in a WLCSP-6(1.38x0.94). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| A1 | SDA | bidirectional | Serial interface data: I2C input/output data line with open-drain output; do not leave this pin floating. |
| A2 | VIN | power_in | Power input to the converter; place the input decoupling capacitor as close to this pin as possible. |
| B1 | SCL | input | I2C clock input; holding this pin low for 100 ms generates a hardware reset, and it must not be left floating. |
| B2 | SW | output | Switching node; connect to one side of the inductor. |
| C1 | FB | input | Feedback input; connect to the positive side of the output capacitor. |
| C2 | GND | power_in | Power and IC ground; all signals are referenced to this pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | WLCSP-6(1.38x0.94) |
| Category | Power Management |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | -0.3 | 6 | V | 4 | ||
| Voltage on SW Pin | VSW | -0.3 | 6 | V | 4 | ||
| SDA and SCL Pins | VCTRL | -0.3 | V | 4 | |||
| FB Pin | FB | -0.3 | V | 4 | |||
| Junction Temperature | TJ | -40 | 150 | C | 4 | ||
| Storage Temperature | TSTG | -40 | 150 | C | 4 | ||
| Supply Voltage Range | VIN | 2.3 | 5.5 | V | 4 | ||
| Inductor | L | 0.47 | H | 4 | |||
| Input Capacitor | CIN | 4.7 | F | 4 | |||
| Output Current | IOUT | 1000 | mA | 4 | |||
| Operating Ambient Temperature | TA | -25 | 85 | C | 4 | ||
| Junction Temperature | TJ | -40 | 125 | C | 4 | ||
| Junction-to-Ambient Thermal Resistance | QJA | 65 | C/W | 4 | |||
| Programmable Voltage Slew Rate for 0.5 to 3.75 mV/s | VODVS_ACC | -10 | 10 | % | VIN = 2.3 to 4.9 V & VIN > VOUT + 500 mV | 5 | |
| Programmable Voltage Slew Rate for 5 mV/s and 10 mV/s | VODVS_ACC | -20 | 20 | % | VIN = 2.3 to 4.9 V & VIN > VOUT + 500 mV | 5 | |
| Period from I2C command to ramp start | TDVS | 40 | s | VIN = 2.3 to 4.9 V & VIN > VOUT + 500 mV | 5 | ||
| Output Voltage Accuracy (PWM) | VOUTACC | -40 | 40 | mV | VIN = 2.3 to 4.9 V & VIN > VOUT + 500 mV, VOUT = 1.5 V to 3.3 V, Forced PWM Mode, IOUT = 0 A; -40C to 85C | 5 | |
| Output Voltage Accuracy (PFM) | VOUTACC | -2 | 3 | % | VIN = 2.3 to 4.9 V & VIN > VOUT + 500 mV, VOUT = 1.5 V to 3.3 V, PFM Mode, IOUT = 0 A; -40C to 85C | 5 | |
| Peak Inductor Current Limit Accuracy (1.0 A pk setting) | ILIMPWM_ACC | -25 | 25 | % | Peak current accuracy for 1.0 A pk setting, open loop | 5 | |
| Peak Inductor Current Limit Accuracy (> 1.0 A pk setting) | ILIMPWM_ACC | -12 | 12 | % | Peak current accuracy for > 1.0 A pk setting, open loop | 5 | |
| PFM Peak Current Accuracy (< 1.0 A pk setting) | ILIMPFM_ACC | -30 | 30 | % | PFM peak current accuracy for < 1.0 A pk setting, open loop | 5 | |
| PFM Peak Current Accuracy (> 1.0 A pk setting) | ILIMPFM_ACC | -20 | 20 | % | PFM peak current accuracy for > 1.0 A pk setting, open loop | 5 | |
| Negative Current Limit | ILIMNEG | -700 | -1000 | -1300 | mA | 5 | |
| Under-Voltage Lockout Threshold Rising | VUVLO_RISE | 2.1 | 2.15 | 2.2 | V | VIN | 6 |
| Under-Voltage Lockout Threshold Falling | VUVLO_FALL | 2 | 2.05 | 2.1 | V | VIN | 6 |
| Switching Frequency | FSW | 3 | 3.33 | 3.67 | MHz | PWM, IOUT = 0 A | 6 |
| Output Discharge Resistance | RBK_DIS | 80 | 100 | 120 | 6 | ||
| SDA and SCL Logic Low threshold | VIL | 0.4 | V | 6 | |||
| SDA and SCL Logic High threshold | VIH | 1.2 | 5.5 | V | 6 | ||
| SDA Logic Low Output | VOL | 0.4 | V | 3 mA Sink | 6 | ||
| SDA Sink Current | IOL | 2 | mA | 6 | |||
| SCL Clock Frequency | fSCL | 1000 | kHz | Fast Mode Plus | 6 | ||
| Bus-Free Time Between STOP and START Conditions | tBUF | 0.5 | s | Fast Mode Plus | 6 | ||
| START or Repeated START Hold Time | tHD; STA | 260 | ns | Fast Mode Plus | 6 | ||
| SCL LOW Period | tLOW | 0.5 | s | Fast Mode Plus | 6 | ||
| SCL HIGH Period | tHIGH | 260 | ns | Fast Mode-Plus | 6 | ||
| Repeated START Setup Time | tSU; STA | 260 | ns | Fast Mode-Plus | 6 | ||
| Data Setup Time | tSU; DAT | 50 | ns | Fast Mode Plus | 6 | ||
| Data Valid Time | tVD; DAT | 450 | ns | Fast Mode Plus | 6 | ||
| Data Valid Acknowledge Time | tVD; ACK | 450 | ns | Fast Mode Plus | 6 | ||
| SDA and SCL Rise Time | tR | 120 | ns | Fast Mode Plus | 6 | ||
| SDA and SCL Fall Time | tF | 6.55 | 120 | ns | Fast Mode Plus, VDD = 1.8 V | 6 | |
| Stop Condition Setup Time | tSU; STO | 260 | ns | Fast Mode Plus | 6 | ||
| SDA and SCL Input Capacitance | Ci | 10 | pF | 6 | |||
| Capacitive Load for SDA and SCL | Cb | 550 | pF | 6 | |||
| Spike pulse width that input filter must suppress | tSP | 0 | 50 | ns | SCL, SDA only | 6 | |
| Load Regulation | LOADREG | -5 | 5 | mV | 1 mA ≤ IOUT ≤ 1000 mA, VIN = 2.3 to 4.9 V & VIN > VOUT + 500 mV, VOUT = 1.5, 2.6, 3.2 V FPWM | 7 | |
| Load Transient | VTRRP | -30 | 45 | mV | IOUT = 0 mA <-> 1 A, TR = TF = 500 mA/ms, Auto Mode, VIN = 3.8 V, VOUT = 1.5, 2.6 and 3.2 V | 7 | |
| Line Transient | LINETRAN | -35 | 35 | mV | VIN = 3.0 V <-> 3.6 V, 100 mV/s, IOUT = 300 mA, PWM, VOUT = 2.6 V | 7 | |
| Output Ripple (PFM) | VRIPPLE | 31 | 50 | mV | VIN = 2.3 to 4.9 V, IOUT = 1 mA and 10 mA, PFM Mode, VOUT = 1.5, 2.6 and 3.2 V | 7 | |
| Output Ripple (PWM) | VRIPPLE | 5 | 15 | mV | VIN = 2.3 to 4.9 V, IOUT = 500 mA and 1.0 A, VOUT = 1.5, 2.6 and 3.2 V, PWM Mode | 7 | |
| ESD Human Body Model | ESD | 2 | kV | Human Body Model | 4 | ||
| ESD Charged Device Model | ESD | 500 | V | Charged Device Model | 4 |
CAD (KiCad official)
- Symbol:
FAN53745UC00X - Footprint:
Package_CSP:WLCSP-6_1.4x1.0mm_P0.4mm - 3D model: WLCSP-6(1.38x0.94), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.35 mm nominal DSBGA height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
fan53745uc00x-etched.step/fan53745uc00x-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fan53745uc00x.step/fan53745uc00x.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (37 pp, sha256
70cc4f7d070a1693, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).