3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXD8574AP
XINLUDA · I/O Expanders · DIP-16
XD8574AP from XINLUDA, in a DIP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Hardware address input 0; connect directly to VCC or ground, pull-up resistors are not needed. |
| 2 | A1 | input | Hardware address input 1; connect directly to VCC or ground, pull-up resistors are not needed. |
| 3 | A2 | input | Hardware address input 2; connect directly to VCC or ground, pull-up resistors are not needed. |
| 4 | P0 | bidirectional | Port 0 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 5 | P1 | bidirectional | Port 1 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 6 | P2 | bidirectional | Port 2 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 7 | P3 | bidirectional | Port 3 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 8 | GND | power_in | Supply ground. |
| 9 | P4 | bidirectional | Port 4 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 10 | P5 | bidirectional | Port 5 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 11 | P6 | bidirectional | Port 6 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 12 | P7 | bidirectional | Port 7 input/output (listed as push-pull in the pin table); at power-on P0-P7 are configured as inputs. |
| 13 | INT | output | Interrupt output, active LOW; open-drain design, connect to VCC through a pull-up resistor. |
| 14 | SCL | input | I2C serial clock line; connect to VCC through a pull-up resistor. |
| 15 | SDA | bidirectional | I2C serial data line; connect to VCC through a pull-up resistor. |
| 16 | VCC | power_in | Supply voltage; recommended operating range is +2.3 V to +5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | DIP-16 |
| Category | Interface |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 2.3 | 5.5 | V | VCC(MAX) = 5.5V | 4 | |
| LOW-level input voltage, SCL, SDA | VIL | -0.5 | V | 5 | |||
| LOW-level input voltage, A2-A0, P7-P0 | VIL | -0.5 | V | 5 | |||
| High-level output current, P7-P0 | IOH | -1 | mA | 5 | |||
| Low-level output current, P7-P0 | IOL | 25 | mA | 5 | |||
| Operating free-air temperature | TA | -40 | 85 | °C | 5 | ||
| Supply voltage range | VCC | -0.5 | 7 | V | 4 | ||
| Input pin voltage range | VIN | -0.5 | V | see note [2] | 4 | ||
| Output pin voltage range | VO | -0.5 | V | see note [2] | 4 | ||
| Input clamp current | IIK | -20 | mA | VIN<0 | 4 | ||
| Output clamp current | IOK | -20 | mA | VO<0 | 4 | ||
| Input/output clamp current | IIOK | -400 | 400 | μA | VO<0 or VO>VCC | 4 | |
| Continuous output low current | IOL | 50 | mA | VO = 0 to VCC | 4 | ||
| Continuous output high current | IOH | -4 | mA | VO = 0 to VCC | 4 | ||
| Continuous current through GND | ICC | -100 | mA | 4 | |||
| Continuous current through VCC | 100 | mA | 4 | ||||
| Total power dissipation | Ptot | 400 | mW | 4 | |||
| Storage temperature range | Tstg | -65 | 150 | °C | 4 | ||
| Ambient temperature range | Tamb | -40 | 85 | °C | Operating | 4 | |
| Supply current, operating mode | ICC | 40 | 100 | μA | I/O = inputs, VIN = VCC or GND, fSCL = 100 kHz, IO = 0, No load; VCC = +5.5V | 5 | |
| Standby current, standby mode | ISTB | 2.5 | 10 | μA | I/O = inputs, VIN = VCC or GND, fSCL = 0 kHz, IO = 0, No load; VCC = +5.5V | 5 | |
| Power-on reset voltage, VCC rising | VPOR | 1.3 | 2.4 | V | VIN = VCC or GND, IO = 0, No load; VCC = +5.5V | 5 | |
| LOW-level input voltage, SCL/SDA | VIL | -0.5 | V | VCC 2.3V to 5.5V | 5 | ||
| LOW-level output current, SDA | IOL | 3 | mA | VOL = 0.4 V; VCC 2.3V to 5.5V | 5 | ||
| Input leakage current, SCL/SDA | IL | -1 | 1 | μA | VIN = VCC or GND; VCC 2.3V to 5.5V | 5 | |
| Input capacitance, SCL/SDA | CI | 3 | 7 | pF | VIN = GND; VCC 2.3V to 5.5V | 5 | |
| LOW-level input voltage, P0-P7 | VIL | -0.5 | V | VCC 2.3V to 5.5V | 5 | ||
| LOW-level output current, P0-P7 | IOL | 10 | 25 | mA | VOL = 1.0V; VCC = +5.5V | 5 | |
| HIGH-level output current, P0-P7 | IOH | 30 | 300 | μA | VOH = GND; VCC = +5.5V | 5 | |
| HIGH-level input leakage current, P0-P7 | ILIH | 5 | μA | VIN = VCC; VCC 2.3V to 5.5V | 5 | ||
| LOW-level input leakage current, P0-P7 | ILIL | -5 | μA | VIN = GND; VCC 2.3V to 5.5V | 5 | ||
| Input capacitance, P0-P7 | CI | 4 | 10 | pF | VCC 2.3V to 5.5V | 5 | |
| Output capacitance, P0-P7 | CO | 4 | 10 | pF | VCC 2.3V to 5.5V | 5 | |
| LOW-level output current, INT | IOL | 1.6 | mA | VOL = 0.4V; VCC 2.3V to 5.5V | 5 | ||
| HIGH-level input leakage current, INT | ILIH | 5 | μA | VIN = VCC; VCC 2.3V to 5.5V | 5 | ||
| LOW-level input leakage current, INT | ILIL | -5 | μA | VIN = GND; VCC 2.3V to 5.5V | 5 | ||
| LOW-level input voltage, A2-A0 | VIL | -0.5 | V | VCC 2.3V to 5.5V | 5 | ||
| HIGH-level input leakage current, A2-A0 | ILIH | 5 | μA | VIN = VCC; VCC 2.3V to 5.5V | 5 | ||
| LOW-level input leakage current, A2-A0 | ILIL | -5 | μA | VIN = GND; VCC 2.3V to 5.5V | 5 | ||
| SCL clock frequency | fSCL | 0 | 100 | kHz | Standard-mode | 6 | |
| Free time between STOP and START | tBUF | 4.7 | μs | Standard-mode | 6 | ||
| Hold time (repeated) START condition | tHD:STA | 4 | μs | Standard-mode | 6 | ||
| Set-up time for repeated START condition | tSU:STA | 4.7 | μs | Standard-mode | 6 | ||
| Set-up time for STOP condition | tSU:STO | 4 | μs | Standard-mode | 6 | ||
| Data valid acknowledge time | tVD:ACK | 0 | 3.4 | μs | 6 | ||
| Data hold time | tHD:DAT | 0 | ns | Standard-mode | 6 | ||
| Data valid time | tVD:DAT | 0 | 3.4 | μs | 6 | ||
| Data set-up time | tSU:DAT | 250 | ns | Standard-mode | 6 | ||
| LOW period of the SCL clock | tLOW | 4.7 | μs | Standard-mode | 6 | ||
| HIGH period of the SCL clock | tHIGH | 4 | μs | Standard-mode | 6 | ||
| Fall time of SDA and SCL | tf | 0.3 | μs | Standard-mode | 6 | ||
| Rise time of SDA and SCL | tr | 1 | μs | Standard-mode | 6 | ||
| Pulse width of spikes suppressed by input filter | tsp | 50 | ns | 6 | |||
| I2C-bus capacitive load | Cb | 400 | pF | 6 | |||
| Output data valid time | tpv(Q) | 4 | μs | CL ≤ 100pF | 6 | ||
| Input data set-up time | tps(D) | 0 | μs | CL ≤ 100pF | 6 | ||
| Input data hold time | tph(D) | 4 | μs | CL ≤ 100pF | 6 | ||
| Interrupt valid time, INT from port | tiv(INT_N) | 4 | μs | CL ≤ 100pF | 6 | ||
| Interrupt reset delay time, INT from SCL | tirst(INT_N) | 4 | μs | CL ≤ 100pF | 6 | ||
| Package thermal resistance, junction-to-ambient (free air), DIP16 | RθJA | 48.3 | °C/W | DIP16 column; minimum pad spacing on FR4 PCB, no air flow | 4 |
CAD (KiCad official)
- Symbol:
XD8574AP - Footprint:
Package_DIP:DIP-16_W7.62mm - 3D model: DIP-16 (KiCad packages3D, STEP)
- 3D model files:
xd8574ap-etched.step/xd8574ap-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xd8574ap.step/xd8574ap.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (22 pp, sha256
626605a32f9b6519, retrieved 2026-10-15, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).