3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHV2901K6-G
Microchip Tech · Analog Switches, Multiplexers · QFN-64-EP(9x9)
HV2901K6-G from Microchip Tech, in a QFN-64-EP(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW30 | passive | Analog switch 30 terminal; the analog signal must stay between VNN and VPP. |
| 2 | Y3031 | passive | Common terminal shared by analog switches 30 and 31; the analog signal must stay between VNN and VPP. |
| 3 | SW31 | passive | Analog switch 31 terminal; the analog signal must stay between VNN and VPP. |
| 4 | NC | unconnected | No connection. |
| 5 | CLR | input | Clear logic input; it overrides all other inputs and opens all switches when high, and logic inputs accept 3.3 V or 5 V CMOS levels (VIH min 0.9×VDD, VIL max 0.1×VDD). |
| 6 | NC | unconnected | No connection. |
| 7 | LE | input | Latch-enable logic input, active low; the logic input accepts 3.3 V or 5 V CMOS levels (VIH min 0.9×VDD, VIL max 0.1×VDD). |
| 8 | CLK | input | Clock logic input for the shift register, with data clocked in on the rising edge; the maximum clock frequency is 20 MHz at VDD = 5 V and 8 MHz at VDD = 3 V. |
| 9 | VDD | power_in | Logic supply voltage, 3 V to 5.5 V. |
| 10 | DIN | input | Serial data input to the 32-bit shift register; the logic input accepts 3.3 V or 5 V CMOS levels (VIH min 0.9×VDD, VIL max 0.1×VDD). |
| 11 | GND | power_in | Ground reference for the logic circuitry. |
| 12 | DOUT | output | Serial data output of the shift register; it is high when register bit 31 is high. |
| 13 | NC | unconnected | No connection. |
| 14 | SW0 | passive | Analog switch 0 terminal; the analog signal must stay between VNN and VPP. |
| 15 | Y01 | passive | Common terminal shared by analog switches 0 and 1; the analog signal must stay between VNN and VPP. |
| 16 | SW1 | passive | Analog switch 1 terminal; the analog signal must stay between VNN and VPP. |
| 17 | SW2 | passive | Analog switch 2 terminal; the analog signal must stay between VNN and VPP. |
| 18 | Y23 | passive | Common terminal shared by analog switches 2 and 3; the analog signal must stay between VNN and VPP. |
| 19 | SW3 | passive | Analog switch 3 terminal; the analog signal must stay between VNN and VPP. |
| 20 | SW4 | passive | Analog switch 4 terminal; the analog signal must stay between VNN and VPP. |
| 21 | Y45 | passive | Common terminal shared by analog switches 4 and 5; the analog signal must stay between VNN and VPP. |
| 22 | SW5 | passive | Analog switch 5 terminal; the analog signal must stay between VNN and VPP. |
| 23 | SW6 | passive | Analog switch 6 terminal; the analog signal must stay between VNN and VPP. |
| 24 | Y67 | passive | Common terminal shared by analog switches 6 and 7; the analog signal must stay between VNN and VPP. |
| 25 | SW7 | passive | Analog switch 7 terminal; the analog signal must stay between VNN and VPP. |
| 26 | SW8 | passive | Analog switch 8 terminal; the analog signal must stay between VNN and VPP. |
| 27 | Y89 | passive | Common terminal shared by analog switches 8 and 9; the analog signal must stay between VNN and VPP. |
| 28 | SW9 | passive | Analog switch 9 terminal; the analog signal must stay between VNN and VPP. |
| 29 | SW10 | passive | Analog switch 10 terminal; the analog signal must stay between VNN and VPP. |
| 30 | Y1011 | passive | Common terminal shared by analog switches 10 and 11; the analog signal must stay between VNN and VPP. |
| 31 | SW11 | passive | Analog switch 11 terminal; the analog signal must stay between VNN and VPP. |
| 32 | SW12 | passive | Analog switch 12 terminal; the analog signal must stay between VNN and VPP. |
| 33 | Y1213 | passive | Common terminal shared by analog switches 12 and 13; the analog signal must stay between VNN and VPP. |
| 34 | SW13 | passive | Analog switch 13 terminal; the analog signal must stay between VNN and VPP. |
| 35 | VPP | power_in | Positive high-voltage supply, +40 V to VNN+200 V, with VPP-VNN not exceeding 220 V. |
| 36 | RGND | power_in | Ground return for the HV2901 output bleed resistors (20 to 50 kΩ); this pin is NC on the HV2801. |
| 37 | VNN | power_in | Negative high-voltage supply, -160 V to -40 V. |
| 38 | SW14 | passive | Analog switch 14 terminal; the analog signal must stay between VNN and VPP. |
| 39 | Y1415 | passive | Common terminal shared by analog switches 14 and 15; the analog signal must stay between VNN and VPP. |
| 40 | SW15 | passive | Analog switch 15 terminal; the analog signal must stay between VNN and VPP. |
| 41 | SW16 | passive | Analog switch 16 terminal; the analog signal must stay between VNN and VPP. |
| 42 | Y1617 | passive | Common terminal shared by analog switches 16 and 17; the analog signal must stay between VNN and VPP. |
| 43 | SW17 | passive | Analog switch 17 terminal; the analog signal must stay between VNN and VPP. |
| 44 | VNN | power_in | Negative high-voltage supply, -160 V to -40 V. |
| 45 | RGND | power_in | Ground return for the HV2901 output bleed resistors (20 to 50 kΩ); this pin is NC on the HV2801. |
| 46 | VPP | power_in | Positive high-voltage supply, +40 V to VNN+200 V, with VPP-VNN not exceeding 220 V. |
| 47 | SW18 | passive | Analog switch 18 terminal; the analog signal must stay between VNN and VPP. |
| 48 | Y1819 | passive | Common terminal shared by analog switches 18 and 19; the analog signal must stay between VNN and VPP. |
| 49 | SW19 | passive | Analog switch 19 terminal; the analog signal must stay between VNN and VPP. |
| 50 | SW20 | passive | Analog switch 20 terminal; the analog signal must stay between VNN and VPP. |
| 51 | Y2021 | passive | Common terminal shared by analog switches 20 and 21; the analog signal must stay between VNN and VPP. |
| 52 | SW21 | passive | Analog switch 21 terminal; the analog signal must stay between VNN and VPP. |
| 53 | SW22 | passive | Analog switch 22 terminal; the analog signal must stay between VNN and VPP. |
| 54 | Y2223 | passive | Common terminal shared by analog switches 22 and 23; the analog signal must stay between VNN and VPP. |
| 55 | SW23 | passive | Analog switch 23 terminal; the analog signal must stay between VNN and VPP. |
| 56 | SW24 | passive | Analog switch 24 terminal; the analog signal must stay between VNN and VPP. |
| 57 | Y2425 | passive | Common terminal shared by analog switches 24 and 25; the analog signal must stay between VNN and VPP. |
| 58 | SW25 | passive | Analog switch 25 terminal; the analog signal must stay between VNN and VPP. |
| 59 | SW26 | passive | Analog switch 26 terminal; the analog signal must stay between VNN and VPP. |
| 60 | Y2627 | passive | Common terminal shared by analog switches 26 and 27; the analog signal must stay between VNN and VPP. |
| 61 | SW27 | passive | Analog switch 27 terminal; the analog signal must stay between VNN and VPP. |
| 62 | SW28 | passive | Analog switch 28 terminal; the analog signal must stay between VNN and VPP. |
| 63 | Y2829 | passive | Common terminal shared by analog switches 28 and 29; the analog signal must stay between VNN and VPP. |
| 64 | SW29 | passive | Analog switch 29 terminal; the analog signal must stay between VNN and VPP. |
| 65 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-64-EP(9x9) |
| Category | Interface |
| Pins | 65 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic Power Supply Voltage | VDD | -0.5 | 6.5 | V | 3 | ||
| Differential Supply Voltage | VPP-VNN | 220 | V | 3 | |||
| High-Voltage Positive Supply | VPP | -0.5 | V | 3 | |||
| High-Voltage Negative Supply | VNN | -200 | 0.5 | V | 3 | ||
| Logic Input Voltage | -0.5 | V | 3 | ||||
| Peak Analog Signal Current per Channel | 3 | A | 3 | ||||
| Storage Temperature | TS | -65 | 150 | °C | 3 | ||
| Power Dissipation, 64-lead QFN | 1.5 | W | 3 | ||||
| Logic Power Supply Voltage | VDD | 3 | 5.5 | V | Note 1, Note 3 | 3 | |
| High-Voltage Positive Supply | VPP | 40 | V | Note 1, Note 3 | 3 | ||
| High-Voltage Negative Supply | VNN | -160 | -40 | V | Note 1, Note 3 | 3 | |
| Low-Level Input Voltage | VIL | 0 | V | 3 | |||
| Operating Ambient Temperature | TA | 0 | 70 | °C | 7 | ||
| Small Signal Switch On-Resistance | RONS | 26 | 38 | Ω | +25°C; ISIG = 5 mA, VPP = +40V, VNN = -160V | 4 | |
| Small Signal Switch On-Resistance | RONS | 22 | 27 | Ω | +25°C; ISIG = 200 mA, VPP = +40V, VNN = -160V | 4 | |
| Small Signal Switch On-Resistance | RONS | 18 | 24 | Ω | +25°C; ISIG = 200 mA, VPP = +100V, VNN = -100V | 4 | |
| Small Signal Switch On-Resistance | RONS | 20 | 25 | Ω | +25°C; ISIG = 5 mA, VPP = +160V, VNN = -40V | 4 | |
| Small Signal Switch On-Resistance | RONS | 16 | 25 | Ω | +25°C; ISIG = 200 mA, VPP = +160V, VNN = -40V | 4 | |
| Small Signal Switch On-Resistance Matching | ΔRONS | 5 | 20 | % | +25°C; ISIG = 5 mA, VPP = +100V, VNN = -100V | 4 | |
| Output Bleed Resistor (HV2901 only) | RINT | 20 | 35 | 50 | kΩ | +25°C; Output Switch to RGND, IRINT = 0.5 mA | 4 |
| Switch-Off Leakage per Switch | ISOL | 1 | 10 | μA | +25°C; VSIG = VPP-10V, VNN +10V | 4 | |
| DC Offset Switch Off | VOS | 100 | 300 | mV | +25°C; No load (For HV2901) | 4 | |
| DC Offset Switch On | VOS | 100 | 500 | mV | +25°C; No load (For HV2901) | 4 | |
| Quiescent VPP Supply Current, all switches off | IPPQ | 10 | 50 | μA | +25°C; All switches off | 4 | |
| Quiescent VNN Supply Current, all switches off | INNQ | -10 | -50 | μA | +25°C; All switches off | 4 | |
| Quiescent VPP Supply Current, all switches on | IPPQ | 10 | 50 | μA | +25°C; All switches on, ISW = 5 mA | 4 | |
| Quiescent VNN Supply Current, all switches on | INNQ | -10 | -50 | μA | +25°C; All switches on, ISW = 5 mA | 4 | |
| Switch Output Peak Current | ISW | 3 | 2 | A | +25°C; VSIG duty cycle < 0.1% | 4 | |
| Output Switching Frequency | fSW | 50 | kHz | +25°C; Duty cycle = 50% | 4 | ||
| Average VPP Supply Current | IPP | 20 | mA | +25°C; VPP = +40V, VNN = -160V; 50 kHz switching, no load | 4 | ||
| Average VPP Supply Current | IPP | 14 | mA | +25°C; VPP = +100V, VNN = -100V; 50 kHz switching, no load | 4 | ||
| Average VNN Supply Current | INN | 20 | mA | +25°C; VPP = +40V, VNN = -160V; 50 kHz switching, no load | 4 | ||
| Average VNN Supply Current | INN | 14 | mA | +25°C; VPP = +100V, VNN = -100V; 50 kHz switching, no load | 4 | ||
| Average VDD Supply Current | IDD | 8 | mA | +25°C; fCLK = 5 MHz, VDD = 5V | 5 | ||
| Quiescent VDD Supply Current | IDDQ | 10 | μA | +25°C; All logic inputs are static | 5 | ||
| Data Out Source Current | ISOR | 0.45 | 0.7 | mA | +25°C; VOUT = VDD-0.7V | 5 | |
| Data Out Sink Current | ISINK | 0.45 | 0.7 | mA | +25°C; VOUT = 0.7V | 5 | |
| Logic Input Capacitance | CIN | 10 | pF | +25°C | 5 | ||
| Set-Up Time Before LE Rises | tSD | 25 | ns | +25°C; VDD = 5V, tr = tf ≤ 5 ns, CLOAD = 20 pF (table note) | 5 | ||
| Time Width of LE | tWLE | 56 | ns | +25°C; VDD = 3V | 5 | ||
| Time Width of LE | tWLE | 12 | ns | +25°C; VDD = 5V | 5 | ||
| Clock Delay Time to Data Out | tDO | 8 | 19 | 40 | ns | +25°C; VDD = 3V | 5 |
| Clock Delay Time to Data Out | tDO | 8 | 15 | 30 | ns | +25°C; VDD = 5V | 5 |
| Time Width of CLR | tWCLR | 55 | ns | +25°C | 5 | ||
| Set-Up Time Data to Clock | tSU | 21 | ns | +25°C; VDD = 3V | 5 | ||
| Set-Up Time Data to Clock | tSU | 7 | ns | +25°C; VDD = 5V | 5 | ||
| Hold Time Data from Clock | tH | 5 | ns | +25°C; VDD = 3V | 5 | ||
| Hold Time Data from Clock | tH | 7 | ns | +25°C; VDD = 5V | 5 | ||
| Clock Frequency | fCLK | 8 | MHz | +25°C; VDD = 3V | 5 | ||
| Clock Frequency | fCLK | 20 | MHz | +25°C; VDD = 5V | 5 | ||
| Clock Rise and Fall Times | tr, tf | 50 | ns | +25°C | 5 | ||
| Turn-On Time | tON | 5 | μs | +25°C; VSIG = VPP-10V, RLOAD = 10 kΩ | 5 | ||
| Turn-Off Time | tOFF | 5 | μs | +25°C; VSIG = VPP-10V, RLOAD = 10 kΩ | 5 | ||
| Maximum VSIG Slew Rate | dv/dt | 20 | V/ns | +25°C; VPP = +40V, VNN = -160V | 5 | ||
| Package Thermal Resistance, 64-lead QFN | JA | 21 | °C/W | 7 |
CAD (KiCad official)
- Symbol:
HV2901K6-G - Footprint:
Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm - 3D model: QFN-64-EP(9x9) (KiCad packages3D, STEP)
- 3D model files:
hv2901k6-g-etched.step/hv2901k6-g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hv2901k6-g.step/hv2901k6-g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (20 pp, sha256
08858e659e6260c4, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).