3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownHIN232CBZ
RENESAS · Pre-ordered Chips · SOIC-16-300mil
HIN232CBZ from RENESAS, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C1+ | passive | External charge-pump capacitor C1 (+ terminal) connects to this lead (0.1µF or 1µF). |
| 2 | V+ | power_out | Internally generated positive supply (+10V nominal) from the voltage doubler, with reservoir capacitor to ground. |
| 3 | C1- | passive | External charge-pump capacitor C1 (- terminal) connects to this lead. |
| 4 | C2+ | passive | External charge-pump capacitor C2 (+ terminal) connects to this lead (0.1µF or 1µF). |
| 5 | C2- | passive | External charge-pump capacitor C2 (- terminal) connects to this lead. |
| 6 | V- | power_out | Internally generated negative supply (-10V nominal) from the voltage inverter, with reservoir capacitor to ground. |
| 7 | T2OUT | output | Transmitter 2 output at RS-232 levels (nominally ±10V), short-circuit protected with 300Ω minimum power-off impedance. |
| 8 | R2IN | input | Receiver 2 input accepting RS-232 levels up to ±30V, with internal 5kΩ pull-down to GND. |
| 9 | R2OUT | output | Receiver 2 output at TTL/CMOS levels (0V to VCC). |
| 10 | T2IN | input | Transmitter 2 input accepting TTL/CMOS levels, with internal 400kΩ pull-up resistor to VCC. |
| 11 | T1IN | input | Transmitter 1 input accepting TTL/CMOS levels, with internal 400kΩ pull-up resistor to VCC. |
| 12 | R1OUT | output | Receiver 1 output at TTL/CMOS levels (0V to VCC). |
| 13 | R1IN | input | Receiver 1 input accepting RS-232 levels up to ±30V, with internal 5kΩ pull-down to GND. |
| 14 | T1OUT | output | Transmitter 1 output at RS-232 levels (nominally ±10V), short-circuit protected with 300Ω minimum power-off impedance. |
| 15 | GND | power_in | Ground lead, connect to 0V. |
| 16 | VCC | power_in | Power supply input, 5V ±10%. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | SOIC-16-300mil |
| Category | Interface ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC to Ground | VCC | -0.3 | 6 | V | Relative to GND; printed (GND -0.3V) < VCC < 6V | 9 | |
| V+ to Ground | V+ | 13.2 | V | Printed (VCC -0.3V) < V+ < 13.2V; carries Note 2 (Only HIN239) | 9 | ||
| V- to Ground | V- | -12 | 0.3 | V | Relative to GND; printed -12V < V- < (GND +0.3V) | 9 | |
| V+ to V- | V+ - V- | 24 | V | 9 | |||
| RIN input voltage | RIN | 30 | V | 9 | |||
| ROUT output voltage | VRXOUT | -0.3 | V | Relative to GND; printed (GND -0.3V) < VRXOUT < (V+ +0.3V) | 9 | ||
| Maximum junction temperature (plastic package) | 150 | °C | 9 | ||||
| Maximum storage temperature range | -65 | 150 | °C | 9 | |||
| VCC supply tolerance | VCC | -10 | 10 | % | VCC = +5V ±10% | 9 | |
| Operating temperature range (HIN2xxCx, commercial) | 0 | 70 | °C | Applies to HIN232CBZ (commercial, 0 to +70°C) | 9 | ||
| Charge pump input voltage | 5.5 | V | Stated in text: charge pump accepts input voltages up to | 10 | |||
| Thermal resistance, 16 Ld SOIC package | 100 | °C/W | Typical; measured in free air on low effective thermal conductivity test board (Note 3) | 9 | |||
| Supply current ICC | ICC | 5 | 10 | mA | No Load, TA = +25°C | 9 | |
| Input logic low VIL (TIN) | VIL | 0.8 | V | 9 | |||
| Input logic high VIH (TIN) | VIH | 2 | V | 9 | |||
| Transmitter input pull-up current | IP | 15 | 200 | µA | TIN = 0V | 9 | |
| TTL/CMOS receiver output voltage low | VOL | 0.1 | 0.4 | V | IOUT = 1.6mA | 9 | |
| TTL/CMOS receiver output voltage high | VOH | 3.5 | 4.6 | V | IOUT = -1.0mA | 9 | |
| RS-232 input voltage range | VIN | -30 | 30 | V | 9 | ||
| Receiver input impedance | RIN | 3 | 5 | 7 | k | VIN = ±3V | 9 |
| Receiver input low threshold | VIN(H-L) | 0.8 | 1.2 | V | VCC = 5V, TA = +25°C | 9 | |
| Receiver input high threshold | VIN(L-H) | 1.7 | 2.4 | V | VCC = 5V, TA = +25°C | 9 | |
| Receiver input hysteresis | VHYST | 0.2 | 0.5 | 1 | V | 9 | |
| Baud rate (1 transmitter switching) | 120 | kbps | RL = 3k | 10 | |||
| Instantaneous slew rate | SR | 30 | V/µs | CL = 10pF, RL = 3k, TA = +25°C (Note 4) | 10 | ||
| Transmitter output voltage swing | TOUT | 5 | 9 | 10 | V | Transmitter outputs, 3k to Ground | 10 |
| Output resistance (TOUT, powered down) | 300 | VCC = V+ = V- = 0V, VOUT = 2V | 10 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | C2- External capacitor (- terminal) is connected to this lead. TIN Transmitter Inputs. These leads accept TTL/CMOS levels. An internal 400kpull-up resistor to VCC is connected to each lead. | 2 |
CAD (KiCad official)
- Symbol:
HIN232CBZ - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
hin232cbz-etched.step/hin232cbz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hin232cbz.step/hin232cbz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (22 pp, sha256
d4773763df765fad, retrieved 2026-11-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).