3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPI6CB18200ZDIEX
Diodes Incorporated · Clock Buffers, Drivers · TQFN-24-EP(4x4)
PI6CB18200ZDIEX from Diodes Incorporated, in a TQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Internally connected for the feedback loop, so this pin must not be connected externally. |
| 2 | VDD_R | power_in | Power supply for the input differential buffers, nominal 1.8V with a 1.7V to 1.9V range. |
| 3 | IN+ | input | Differential true clock input for the 100MHz, 50MHz or 125MHz reference clock. |
| 4 | IN- | input | Differential complementary clock input paired with IN+. |
| 5 | GND_R | power_in | Ground for the input differential buffers. |
| 6 | GND_DIG | power_in | Ground for the digital circuitry. |
| 7 | VDD_DIG | power_in | Power supply for the digital circuitry, nominal 1.8V. |
| 8 | SCLK | input | CMOS SMBus clock input that is 3.3V tolerant. |
| 9 | SDATA | bidirectional | CMOS SMBus data line that is 3.3V tolerant. |
| 10 | GND | power_in | Ground. |
| 11 | VDDO | power_in | Power supply for the differential outputs, nominal 1.8V. |
| 12 | OE0# | input | Active-low CMOS input that enables the Q0 pair, with an internal pull-down (1 disables outputs, 0 enables outputs). |
| 13 | Q0+ | output | HCSL differential true clock output Q0. |
| 14 | Q0- | output | HCSL differential complementary clock output Q0. |
| 15 | GNDA | power_in | Ground for the analog circuitry. |
| 16 | VDDA | power_in | Power supply for the analog circuitry, nominal 1.8V. |
| 17 | Q1+ | output | HCSL differential true clock output Q1. |
| 18 | Q1- | output | HCSL differential complementary clock output Q1. |
| 19 | OE1# | input | Active-low CMOS input that enables the Q1 pair, with an internal pull-down (1 disables outputs, 0 enables outputs). |
| 20 | VDDO | power_in | Power supply for the differential outputs, nominal 1.8V. |
| 21 | GND | power_in | Ground. |
| 22 | PD# | input | CMOS input where low enters Power Down Mode and a subsequent high exits it, with an internal pull-up. |
| 23 | BW_SEL_TRI | input | Tri-level latch that selects low loop bandwidth, PLL bypass, or high loop bandwidth, with both internal pull-up and pull-down. |
| 24 | NC | unconnected | Internally connected for the feedback loop, so this pin must not be connected externally. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | TQFN-24-EP(4x4) |
| Category | RTC/Clock Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Voltage | VDD, VDDA, VDD_R, VDD_DIG | 1.7 | 1.8 | 1.9 | V | 4 | |
| Output Power Supply Voltage | VDDO | 1.7 | 1.8 | 1.9 | V | 4 | |
| Analog Power Supply Current | IDDA | 4.5 | 6 | mA | VDDA + VDD_R, PLL mode, All outputs active @100MHz | 4 | |
| Power Supply Current | IDD | 8 | 10 | mA | VDD + VDD_DIG, All outputs active @100MHz | 4 | |
| Power Supply Current for Outputs | IDDO | 6 | 8 | mA | All outputs active @100MHz | 4 | |
| Analog Power Supply Power Down Current | IDDA_PD | 0.7 | 1 | mA | VDDA + VDD_R, PLL mode, All outputs active @100MHz | 4 | |
| Power Supply Power Down Current | IDD_PD | 1.4 | mA | VDD + VDD_DIG+ VDDO, All outputs LOW/LOW | 4 | ||
| Ambient Temperature | TA | -40 | 85 | °C | Industrial grade | 4 | |
| Internal pull up resistance | Rpu | 120 | KW | 4 | |||
| Internal pull down resistance | Rdn | 120 | KW | 4 | |||
| Pin inductance | LPIN | 7 | nH | 4 | |||
| Storage Temperature | -65 | 150 | °C | 4 | |||
| Junction Temperature | 125 | °C | 4 | ||||
| Supply Voltage to Ground Potential | VDDxx | -0.5 | 2.5 | V | 4 | ||
| Input Voltage | -0.5 | 2.5 | V | VDD+0.5V, not exceed 2.5V | 4 | ||
| SMBus Input High Voltage | 3.6 | V | 4 | ||||
| ESD Protection (HBM) | 2000 | V | 4 | ||||
| Nominal bus voltage | VDDSMB | 1.7 | 3.6 | V | 5 | ||
| SMBus Input High Voltage | VIHSMB | 2.1 | 3.6 | V | SMBus, VDDSMB = 3.3V | 5 | |
| SMBus Input Low Voltage | VILSMB | 0.6 | V | SMBus, VDDSMB = 3.3V | 5 | ||
| SMBus sink current | ISMBSINK | 4 | mA | SMBus, at VOLSMB | 5 | ||
| SMBus Output Low Voltage | VOLSMB | 0.4 | V | SMBus, at ISMBSINK | 5 | ||
| SMBus operating frequency | fMAXSMB | 400 | kHz | Maximum frequency | 5 | ||
| SMBus rise time | tRMSB | 1000 | ns | (Max VIL - 0.15) to (Min VIH + 0.15) | 5 | ||
| SMBus fall time | tFMSB | 300 | ns | (Min VIH + 0.15) to (Max VIL - 0.15) | 5 | ||
| Input Low Voltage | VIL | -0.3 | V | Single-ended inputs, except SMBus | 5 | ||
| Input High Current | IIH | 20 | µA | Single-ended inputs, VIN = VDD | 5 | ||
| Input Low Current | IIL | -20 | µA | Single-ended inputs, VIN = 0V | 5 | ||
| Input High Current | IIH | 220 | µA | Single-ended inputs with pull up / pull down resistor, VIN = VDD | 5 | ||
| Input Low Current | IIL | -220 | µA | Single-ended inputs with pull up / pull down resistor, VIN = 0V | 5 | ||
| Input Capacitance | CIN | 1.5 | 5 | pF | 5 | ||
| Output enable latency | tOELAT | 1 | 3 | clocks | Q start after OE# assertion | 5 | |
| PD# de-assertion | tPDLAT | 20 | 300 | us | Differential outputs enable after PD# de-assertion | 5 | |
| Diff. Input High Voltage | VIHDIF | 600 | 800 | 1150 | mV | IN+, IN-, single-end measurement | 6 |
| Diff. Input Low Voltage | VILDIF | -300 | 0 | 300 | mV | IN+, IN-, single-end measurement | 6 |
| Diff. Input Common Mode Voltage | VCOM | 150 | 1000 | mV | 6 | ||
| Diff. Input Swing Voltage | VSWING | 300 | 1450 | mV | Peak to peak value (VIHDIF - VILDIF) | 6 | |
| Input Frequency | fINBP | 1 | 200 | MHz | PLL Bypass mode | 6 | |
| Input Frequency 100MHz PLL | fIN100 | 60 | 100 | 110 | MHz | 6 | |
| Input Frequency 125MHz PLL | fIN125 | 75 | 125 | 137.5 | MHz | 6 | |
| Input Frequency 50MHz PLL | fIN156 | 30 | 50 | 65 | MHz | 6 | |
| Clock stabilization | tSTAB | 0.6 | 1 | ms | From VDD Power-Up and after input clock stabilization or de-assertion of PD# to 1st clock | 6 | |
| Diff. Input Slew Rate | tRF | 0.4 | V/ns | Measured differentially | 6 | ||
| Diff. Input Leakage Current | IIN | -5 | 0.01 | 5 | uA | VIN = VDD, VIN = GND | 6 |
| Diff. Input Duty Cycle | tDC | 45 | 55 | % | Measured differentially | 6 | |
| Diff. Input Cycle to cycle jitter | tjc-c | 125 | ps | Measured differentially | 6 | ||
| Output Voltage High | VOH | 660 | 774 | 900 | mV | Statistical measurement on single-ended signal using oscilloscope math function | 6 |
| Output Voltage Low | VOL | -150 | 150 | mV | 6 | ||
| Output Voltage Maximum | VOMAX | 821 | 1150 | mV | Measurement on single ended signal using absolute value | 6 | |
| Output Voltage Minimum | VOMIN | -300 | -15 | mV | 6 | ||
| Output Swing Voltage | VOSWING | 300 | 1536 | mV | Scope averaging off | 6 | |
| Output Cross Voltage | VOC | 250 | 430 | 550 | mV | 6 | |
| VOC Magnitude Change | DVOC | 12 | 140 | mV | 6 | ||
| Output Frequency | fOUT | 100 | MHz | 7 | |||
| PLL bandwidth | BW | 2 | 2.7 | 4 | MHz | -3dB point in High Bandwidth Mode | 7 |
| PLL bandwidth | BW | 1 | 1.4 | 2 | MHz | -3dB point in Low Bandwidth Mode | 7 |
| PLL Jitter Peaking | tjpeak | 1.2 | 2 | dB | Peak pass band gain | 7 | |
| Slew rate fast setting | tRF | 2.2 | 3 | 6 | V/ns | Scope averaging on fast setting | 7 |
| Slew rate slow setting | tRF | 0.4 | 2 | 3 | V/ns | Scope averaging on slow setting | 7 |
CAD (KiCad official)
- Symbol:
PI6CB18200ZDIEX - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: TQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
pi6cb18200zdiex-etched.step/pi6cb18200zdiex-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pi6cb18200zdiex.step/pi6cb18200zdiex.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (16 pp, sha256
5f5207297479aa11, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).