Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

24AA02E48T-I

Microchip Tech · EEPROM · SOT-23-5

24AA02E48T-I from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 SCL input Serial clock input that synchronizes data transfer to and from the device, with Schmitt Trigger inputs for noise suppression and 100 kHz and 400 kHz clock compatibility (100 kHz only for VCC < 2.5V).
2 VSS power_in Ground reference for the device; all inputs and outputs are referenced to VSS and must stay within -0.3V to VCC + 1.0V.
3 SDA bidirectional Open-drain serial address/data I/O that requires a pull-up resistor to VCC (typical 10 kΩ for 100 kHz, 2 kΩ for 400 kHz) and may change only while SCL is low, except for Start and Stop conditions.
4 VCC power_in Power supply, operating from 1.7V to 5.5V; the internal erase/write logic is disabled if VCC falls below 1.5V at nominal conditions.
5 NC unconnected Not connected on the 5-lead SOT-23 package.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOT-23-5
Category Memory
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
High-Level Input Voltage VIH 0.7 VCC 3
Low-Level Input Voltage VIL 0.3 VCC 3
Hysteresis of Schmitt Trigger Inputs VHYS 0.05 VCC Note 1 3
Low-Level Output Voltage VOL 0.4 V IOL = 3.0 mA, VCC = 2.5V 3
Input Leakage Current ILI -1 1 µA VIN = VSS or VCC 3
Output Leakage Current ILO -1 1 µA VOUT = VSS or VCC 3
Pin Capacitance (all inputs/outputs) CIN, COUT 10 pF VCC = 5.0V (Note 1); TA = +25°C, FCLK = 1 MHz 3
Operating Current (write) ICCWRITE 3 mA VCC = 5.5V, SCL = 400 kHz 3
Operating Current (read) ICCREAD 1 mA 3
Standby Current (Industrial) ICCS 1 µA Industrial (I); SDA = SCL = VCC 3
Clock Frequency FCLK 400 kHz 2.5V <= VCC <= 5.5V 4
Clock Frequency FCLK 100 kHz 1.7V <= VCC <= 2.5V 4
Clock High Time THIGH 600 ns 2.5V <= VCC <= 5.5V 4
Clock High Time THIGH 4000 ns 1.7V <= VCC <= 2.5V 4
Clock Low Time TLOW 1300 ns 2.5V <= VCC <= 5.5V 4
Clock Low Time TLOW 4700 ns 1.7V <= VCC <= 2.5V 4
SDA and SCL Rise Time TR 300 ns 2.5V <= VCC <= 5.5V (Note 1) 4
SDA and SCL Rise Time TR 1000 ns 1.7V <= VCC <= 2.5V (Note 1) 4
SDA and SCL Fall Time TF 300 ns Note 1 4
Start Condition Hold Time THD:STA 600 ns 2.5V <= VCC <= 5.5V 4
Start Condition Hold Time THD:STA 4000 ns 1.7V <= VCC <= 2.5V 4
Start Condition Setup Time TSU:STA 600 ns 2.5V <= VCC <= 5.5V 4
Start Condition Setup Time TSU:STA 4700 ns 1.7V <= VCC <= 2.5V 4
Data Input Hold Time THD:DAT 0 ns Note 2 4
Data Input Setup Time TSU:DAT 100 ns 2.5V <= VCC <= 5.5V 4
Data Input Setup Time TSU:DAT 250 ns 1.7V <= VCC <= 2.5V 4
Stop Condition Setup Time TSU:STO 600 ns 2.5V <= VCC <= 5.5V 4
Stop Condition Setup Time TSU:STO 4000 ns 1.7V <= VCC <= 2.5V 4
Output Valid from Clock TAA 900 ns 2.5V <= VCC <= 5.5V (Note 2) 4
Output Valid from Clock TAA 3500 ns 1.7V <= VCC <= 2.5V (Note 2) 4
Bus Free Time TBUF 1300 ns 2.5V <= VCC <= 5.5V 4
Bus Free Time TBUF 4700 ns 1.7V <= VCC <= 2.5V 4
Output Fall Time from VIH Minimum to VIL Maximum TOF 250 ns 2.5V <= VCC <= 5.5V 4
Input Filter Spike Suppression (SDA and SCL pins) TSP 50 ns Notes 1 and 3 4
Write Cycle Time (byte or page) TWC 5 ms byte or page 4
Endurance 1e+06 cycles +25°C, 5.5V, Page Mode (Note 4) 4
All inputs and outputs w.r.t. VSS -0.3 V Maximum printed as VCC + 1.0V 3
Storage temperature TSTG -65 150 °C 3
Ambient temperature with power applied TA -40 125 °C 3
Supply voltage VCC (operating range) VCC 1.7 5.5 V Electrical characteristics range, Industrial (I) and Extended (E) 3
Ambient temperature (Industrial) TA -40 85 °C Industrial (I) 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 18

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: 24AA02E48T-I
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: 24aa02e48t-i-etched.step / 24aa02e48t-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 24aa02e48t-i.step / 24aa02e48t-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (32 pp, sha256 b1affadbc4fc774a, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF