3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTLV9032L
Texas Instruments · IC · X2QFN-10 (RUG)
TLV9032L from Texas Instruments, in a X2QFN-10 (RUG). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V- | power_in | Negative supply voltage; supply range is 1.65V to 5.5V measured as (V+) minus (V-), and split or single supplies with GND on V- are both allowed. |
| 2 | CLR A | input | Clear input for comparator A that clears the output latch on a falling edge; inputs are rated from (V-) -0.2V to 5.5V recommended and -0.3V to 6V absolute maximum. |
| 3 | CLR B | input | Clear input for comparator B that clears the output latch on a falling edge; inputs are rated from (V-) -0.2V to 5.5V recommended and -0.3V to 6V absolute maximum. |
| 4 | IN+ B | input | Non-inverting (+) input of comparator B; recommended input common mode range is (V-) -0.2V to (V+) +0.2V. |
| 5 | IN- B | input | Inverting (-) input of comparator B; recommended input common mode range is (V-) -0.2V to (V+) +0.2V. |
| 6 | V+ | power_in | Positive supply voltage; supply range is 1.65V to 5.5V measured as (V+) minus (V-). |
| 7 | OUT B | output | Output of comparator B; open-drain option (TLV902xL) or push-pull option (TLV903xL). |
| 8 | OUT A | output | Output of comparator A; open-drain option (TLV902xL) or push-pull option (TLV903xL). |
| 9 | IN- A | input | Inverting (-) input of comparator A; recommended input common mode range is (V-) -0.2V to (V+) +0.2V. |
| 10 | IN+ A | input | Non-inverting (+) input of comparator A; recommended input common mode range is (V-) -0.2V to (V+) +0.2V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | X2QFN-10 (RUG) |
| Category | |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input threshold voltage | VT | -1.75 | 0.3 | 1.75 | mV | VS = 1.8V and 5V | 7 |
| Input threshold voltage | VT | -2.25 | 2.25 | mV | VS = 1.8V and 5V, TA = -40°C to +125°C | 7 | |
| Input threshold voltage drift | dVT/dT | -0.5 | 0.5 | µV/°C | VS = 1.8V and 5V, TA = -40°C to +125°C | 7 | |
| Quiescent current per comparator | IQ | 22 | 30 | µA | VS = 1.8V and 5V, No Load, Output Low | 7 | |
| Quiescent current per comparator | IQ | 42 | µA | VS = 1.8V and 5V, No Load, Output Low, TA = -40°C to +125°C | 7 | ||
| Power-supply rejection ratio (push-pull) | PSRR | 75 | 95 | dB | VS = 1.8V to 5V, TA = -40°C to +125°C (push-pull only) | 7 | |
| Power-supply rejection ratio (open drain) | PSRR | 80 | 95 | dB | VS = 1.8V to 5V, TA = -40°C to +125°C (open drain only) | 7 | |
| Common-mode rejection ratio | CMRR | 60 | 70 | dB | VS = 5V, (V-), 0.2V < VCM < (V+) + 0.2V, TA = -40°C to +125°C | 7 | |
| Common-mode rejection ratio | CMRR | 50 | 60 | dB | VS = 1.8V, (V-), 0.2V < VCM < (V+) + 0.2V, TA = -40°C to +125°C | 7 | |
| Voltage swing from (V-) | VOL | 75 | 125 | mV | ISINK = 4mA, TA = 25°C | 7 | |
| Voltage swing from (V-) | VOL | 175 | mV | ISINK = 4mA, TA = -40°C to +125°C | 7 | ||
| Voltage swing from (V+) | VOH | 75 | 125 | mV | ISOURCE = 4mA, TA = 25°C (push-pull only) | 7 | |
| Voltage swing from (V+) | VOH | 175 | mV | ISOURCE = 4mA, TA = -40°C to +125°C (push-pull only) | 7 | ||
| Short-circuit current, sinking | ISC | 75 | 85 | mA | VS = 5V, Sinking | 7 | |
| Short-circuit current, sourcing | ISC | 75 | 85 | mA | VS = 5V, Sourcing (push-pull only) | 7 | |
| Clear fall to latch reset propagation delay | TPD-CLR-F | 25 | 70 | ns | CLR = 1.8V to 5V, Delay from CLR falling edge signal to unlatched output condition | 8 | |
| Absolute maximum supply voltage | VS | -0.3 | 6 | V | VS = (V+), (V-) | 5 | |
| Absolute maximum input pin voltage | -0.3 | 6 | V | Input pins (IN+, IN-, CLR) from (V-) | 5 | ||
| Absolute maximum input pin current | -10 | 10 | mA | Current into input pins (IN+, IN-, CLR) | 5 | ||
| Absolute maximum output voltage | -0.3 | 6 | V | Output (OUT) from (V-) | 5 | ||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Supply voltage | VS | 1.65 | 5.5 | V | VS = (V+), (V-) | 5 | |
| Input voltage range | -0.2 | 5.5 | V | Input voltage range (IN+, IN-, CLR) from (V-) | 5 | ||
| Output voltage range, open drain | 0 | 5.5 | V | Output voltage range, open drain output, from (V-) | 5 | ||
| Ambient temperature | TA | -40 | 125 | °C | 5 | ||
| Junction-to-ambient thermal resistance (RUG) | RqJA | 222.8 | °C/W | Thermal Information - Dual, RUG (X2QFN) 10 pins | 6 | ||
| Junction-to-case (top) thermal resistance (RUG) | RqJC(top) | 94.2 | °C/W | Thermal Information - Dual, RUG (X2QFN) 10 pins | 6 | ||
| Junction-to-board thermal resistance (RUG) | RqJB | 147.1 | °C/W | Thermal Information - Dual, RUG (X2QFN) 10 pins | 6 | ||
| Junction-to-top characterization parameter (RUG) | yJT | 3.4 | °C/W | Thermal Information - Dual, RUG (X2QFN) 10 pins | 6 | ||
| Junction-to-board characterization parameter (RUG) | yJB | 146.4 | °C/W | Thermal Information - Dual, RUG (X2QFN) 10 pins | 6 |
CAD (Adom-generated)
- Symbol:
TLV9032L - Footprint:
Adom_Gen:Texas_Instruments_TLV9032_b93e43 - 3D model: generated to fit the land (STEP)
- 3D model files:
tlv9032l-etched.step/tlv9032l-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tlv9032l.step/tlv9032l.glbare the bare package body.
Provenance
No distributor stocks TLV9032L yet. This page was built from the datasheet.
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
a8706fdf8ff72411, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.