Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MPQ4570GF-AEC1-Z

Monolithic Power Systems · DC-DC Converters · TSSOP-20-EP

MPQ4570GF-AEC1-Z from Monolithic Power Systems, in a TSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 COMP passive Compensation network setting pin; connect an external resistor in series with a capacitor between this pin and GND.
2 FB input Feedback input to the PWM comparator; connect an external resistive divider between the output and GND (VFB 1V typ).
3 FREQ input Switching frequency setting pin; connect a resistor to GND to set the frequency, or apply an external SYNC clock (100kHz to 1MHz) for the converter to follow.
4 EN input Enable input; pulling it below the threshold (1.3V falling, 1.6V rising typ) shuts the chip down, it has no internal pull-up or pull-down so do not float it.
5 BST passive Bootstrap positive supply for the internal floating high-side MOSFET driver; connect a capacitor between this pin and SW.
6 VIN power_in Input supply (4.5V to 55V) for all internal control circuitry and the VDD regulator; place a decoupling capacitor to ground close to the pin.
7 VIN power_in Input supply (4.5V to 55V) for all internal control circuitry and the VDD regulator; place a decoupling capacitor to ground close to the pin.
8 VIN power_in Input supply (4.5V to 55V) for all internal control circuitry and the VDD regulator; place a decoupling capacitor to ground close to the pin.
9 NC unconnected Not connected pin; float this pin in the application.
10 SW power_out Switch node, the output node from the internal high-side MOSFET source.
11 SW power_out Switch node, the output node from the internal high-side MOSFET source.
12 NC unconnected Not connected pin; float this pin in the application.
13 GND power_in Power ground pin for the internal power MOSFETs.
14 GND power_in Power ground pin for the internal power MOSFETs.
15 GND power_in Power ground pin for the internal power MOSFETs.
16 VDD power_out Internal regulator output (3.6V typ from VIN, 4.8V typ when BIAS is 5V) that powers the internal MOSFET driver and BST charging circuit; needs a 1µF decoupling capacitor.
17 BIAS power_in Connect to an external 5V source for better thermal performance so VDD and internal circuits are powered from BIAS; float or connect to GND if not used.
18 PG output Open-drain power good indication; connect a resistor to a pull-up power source if used.
19 SS passive Optional external soft-start time setting; connect a capacitor to GND, or float for the internal 0.5ms soft-start.
20 AGND power_in Ground for the internal logic and signal circuit.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Monolithic Power Systems
Package TSSOP-20-EP
Category Power Management
Pins 21

CAD (KiCad official)

  • Symbol: MPQ4570GF-AEC1-Z
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: TSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: mpq4570gf-aec1-z-etched.step / mpq4570gf-aec1-z-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mpq4570gf-aec1-z.step / mpq4570gf-aec1-z.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Monolithic Power Systems datasheet (22 pp, sha256 369a892b51791906, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF