3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8619EMSE-5#PBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT8619EMSE-5#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect; this pin is not connected to the internal circuitry. |
| 2 | VIN | power_in | Supplies current to the internal circuitry and the internal top-side power switch, and the input bypass capacitor should be placed as close as possible to this pin and the GND pin; the datasheet gives a 3.0V minimum input voltage and a 60V absolute maximum for VIN. |
| 3 | NC | unconnected | No connect; this pin is not connected to the internal circuitry. |
| 4 | EN/UV | input | Active-high enable with a 1V power-on threshold; forcing it below 0.56V puts the IC into low-current shutdown, a resistor divider from VIN can program VIN undervoltage lockout, and the absolute maximum rating is 60V. |
| 5 | RT | passive | A resistor from this pin to ground sets the switching frequency, and the resistor must be chosen so the frequency is at or below the synchronization frequency when synchronizing; do not apply an external voltage to this pin. |
| 6 | PG | output | Open-drain power good output that stays low until the FB pin is within ±7.5% of the final regulation voltage, with a pull-up to INTVCC, VOUT, or an external supply lower than 6V (absolute maximum 6V). |
| 7 | SYNC | input | External clock synchronization input: tie to a clock for forced continuous mode synchronization, ground for Burst Mode operation, connect to INTVCC for forced continuous mode, or float for pulse-skipping mode; the absolute maximum rating is 6V. |
| 8 | GND | power_in | Ground; connect to the negative terminal of the input capacitor and solder to the PCB to lower thermal resistance. |
| 9 | OUT | input | On the LT8619-5 this pin connects to the regulator output VOUT and to the internal 10MΩ feedback divider that sets the fixed 5V output. |
| 10 | OUT | input | On the LT8619-5 this pin connects to the regulator output VOUT and to the internal 10MΩ feedback divider that sets the fixed 5V output. |
| 11 | BIAS | power_in | When tied above 3.1V the internal regulator draws current from BIAS instead of VIN; for outputs of 3.3V and above it should be tied to VOUT, and the absolute maximum rating is 30V. |
| 12 | INTVCC | power_out | Internal 3.3V regulator output that powers the internal drivers and control circuits, with a maximum external load of 20mA, requires at least 1µF low ESR decoupling to GND, and must not be loaded with external circuitry. |
| 13 | NC | unconnected | No connect; this pin is not connected to the internal circuitry. |
| 14 | BST | passive | Provides a drive voltage above the input voltage to the top-side power switch through a 0.1µF boost capacitor placed as close as possible to the IC, with BST above SW rated at 4V absolute maximum. |
| 15 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor; this node should be kept small on the PCB for good performance. |
| 16 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor; this node should be kept small on the PCB for good performance. |
| 17 | GND | power_in | Exposed pad is ground and must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage (LT8619-5), 25°C | 4.975 | 5 | 5.025 | V | LT8619-5, VIN = 12V, VSYNC = INTVCC, No Load, TA = 25°C | 3 | |
| Regulated Output Voltage (LT8619-5), full operating temperature range | 4.925 | 5 | 5.075 | V | LT8619-5, VIN = 12V, VSYNC = INTVCC, No Load, l (full operating temperature range) | 3 | |
| VIN Quiescent Current at No Load, 25°C | 0.6 | 1 | µA | VIN = 12V, VEN/UV = 0V | 3 | ||
| VIN Quiescent Current at No Load, full operating temperature range | 0.6 | 3 | µA | VIN = 12V, VEN/UV = 0V, l (full operating temperature range) | 3 | ||
| VIN Quiescent Current (Burst Mode, no load), 25°C | 6 | 10 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V | 3 | ||
| VIN Quiescent Current (Burst Mode, no load), full operating temperature range | 6 | 18 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V, l (full operating temperature range) | 3 | ||
| VIN Current in Regulation at ILOAD = 100µA | 38 | 65 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V, ILOAD = 100µA, l (full operating temperature range) | 3 | ||
| VIN Current in Regulation at ILOAD = 1mA | 320 | 400 | µA | VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V, ILOAD = 1mA, l (full operating temperature range) | 3 | ||
| Feedback Voltage Line Regulation (LT8619-5) | -0.03 | 0.004 | 0.03 | %/V | LT8619-5, VIN = 6V to 50V, VSYNC = INTVCC, Note 5 (guaranteed by design, not subject to test) | 3 | |
| Minimum Off-Time | 100 | 150 | 180 | ns | 3 | ||
| Top Switch Peak Current Limit | 1.5 | 1.75 | 2 | A | l (full operating temperature range) | 3 | |
| Operating Frequency, RT = 162k | 260 | 300 | 340 | kHz | RT = 162k, l (full operating temperature range) | 3 | |
| Operating Frequency, RT = 66.5k | 630 | 700 | 770 | kHz | RT = 66.5k, l (full operating temperature range) | 3 | |
| Operating Frequency, RT = 20k | 1.9 | 2 | 2.1 | MHz | RT = 20k, l (full operating temperature range) | 3 | |
| Synchronization Frequency | fSYNC | 0.3 | 2.2 | MHz | fSYNC ≥ fOSC, l (full operating temperature range) | 3 | |
| EN/UV Power-On Threshold | 0.94 | 1 | 1.1 | V | EN/UV rising, l (full operating temperature range) | 4 | |
| EN/UV Shutdown Threshold | 0.34 | 0.56 | 0.92 | V | EN/UV falling, l (full operating temperature range) | 4 | |
| EN/UV Pin Current | -100 | 100 | nA | VEN/UV = 2V | 4 | ||
| Positive Power Good Threshold | 5 | 7.5 | 10 | % | VFB/VOUT rising wrt. regulated VFB/VOUT, l (full operating temperature range) | 4 | |
| Negative Power Good Threshold | -5 | -7.5 | -10 | % | VFB/VOUT rising wrt. regulated VFB/VOUT, l (full operating temperature range) | 4 | |
| PG Leakage | -100 | 100 | nA | VPG = 3.3V, Power Good | 4 | ||
| PG VOL | 0.01 | 0.3 | V | IPG = 100µA, l (full operating temperature range) | 4 | ||
| VIN Minimum Input Voltage | 3 | V | 3 | ||||
| VIN, EN/UV (Absolute Maximum) | VIN, EN/UV | 60 | V | 2 | |||
| BIAS (Absolute Maximum) | BIAS | 30 | V | 2 | |||
| BST Pin Above SW Pin (Absolute Maximum) | 4 | V | BST pin above SW pin | 2 | |||
| PG, SYNC, OUT (Absolute Maximum) | PG, SYNC, OUT | 6 | V | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Operating Junction Temperature (LT8619E-5) | -40 | 125 | °C | LT8619E-5 (E grade, MSE package) | 2 | ||
| Thermal Resistance Junction-to-Ambient, θJA | θJA | 40 | °C/W | MSE package (16-lead plastic MSOP) | 2 | ||
| Thermal Resistance Junction-to-Case, θJC | θJC | 10 | °C/W | MSE package (16-lead plastic MSOP) | 2 |
CAD (KiCad official)
- Symbol:
LT8619EMSE-5#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt8619emse-5-pbf-etched.step/lt8619emse-5-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8619emse-5-pbf.step/lt8619emse-5-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
7156fb4077c7704f, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).