3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMP4558DN-LF-Z
Monolithic Power Systems · DC-DC Converters · SOIC-8-EP
MP4558DN-LF-Z from Monolithic Power Systems, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch node is the output of the high-side switch and requires a low VF Schottky rectifier to ground, placed close to the SW pins to reduce switching spikes. |
| 2 | EN | input | Enable input: pulling it below the specified threshold shuts the chip down, while pulling it above the threshold or leaving it floating enables the chip. |
| 3 | COMP | passive | Compensation pin for the GM error amplifier output, clamped to 0.9V minimum and 2.0V maximum in operation, with the datasheet advising to avoid pulling it above 2.6V. |
| 4 | FB | input | Feedback input to the error amplifier, connected through an external resistive divider and compared to the internal +0.8V reference to set the regulation voltage. |
| 5 | GND | power_in | Ground, connected as close as possible to the output capacitor, with the exposed pad connected to the GND plane for optimal thermal performance. |
| 6 | FREQ | input | Switching frequency program input, where a resistor from this pin to ground sets the switching frequency up to 2MHz. |
| 7 | VIN | power_in | Input supply that powers the internal control circuitry, both BS regulators and the high-side switch, over the 3.8V to 55V recommended supply range. |
| 8 | BST | power_in | Bootstrap positive supply for the internal floating high-side MOSFET driver, with a bypass capacitor connected between this pin and the SW pin. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Monolithic Power Systems |
| Package | SOIC-8-EP |
| Category | Power Management |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Voltage | VFB | 0.78 | 0.8 | 0.82 | V | 4.5V < VIN < 55V, TJ=25°C | 3 |
| Feedback Voltage (over temperature) | VFB | 0.772 | 0.829 | V | 4.5V < VIN < 55V | 3 | |
| Feedback Leakage Current | IFB | 0.1 | 1 | µA | 3 | ||
| Upper Switch On Resistance | RDS(ON) | 175 | 250 | 330 | mΩ | VBST, VSW = 5V, TJ=25°C | 3 |
| Upper Switch On Resistance (over temperature) | RDS(ON) | 160 | 400 | mΩ | VBST, VSW = 5V | 3 | |
| Upper Switch Leakage Current | ISW | 1 | µA | VEN = 0V, VSW = 0V | 3 | ||
| Current Limit | ILIM | 1.3 | 1.9 | 3.5 | A | TJ=25°C, duty cycle ≤60% | 3 |
| Current Limit (over temperature) | ILIM | 1.1 | 3.7 | A | Duty cycle ≤60% | 3 | |
| COMP to Current Sense Transconductance | GCS | 5.7 | A/V | 3 | |||
| Error Amp Voltage Gain | 400 | V/V | 3 | ||||
| Error Amp Transconductance | 120 | µA/V | ICOMP = ±3µA | 3 | |||
| Error Amp Min Source Current | 10 | µA | VFB = 0.7V | 3 | |||
| Error Amp Min Sink Current | -10 | µA | VFB = 0.9V | 3 | |||
| VIN UVLO Threshold | 2.7 | 3 | 3.3 | V | TJ=25°C | 3 | |
| VIN UVLO Threshold (over temperature) | 2.4 | 3.6 | V | 3 | |||
| VIN UVLO Hysteresis | 0.35 | V | 3 | ||||
| Soft-Start Time | 0.5 | ms | 0V < VFB < 0.8V | 3 | |||
| Oscillator Frequency | fSW | 0.8 | 1 | 1.2 | MHz | RFREQ = 95kΩ, TJ=25°C | 3 |
| Oscillator Frequency (over temperature) | fSW | 0.7 | 1.3 | MHz | RFREQ = 95kΩ | 3 | |
| Shutdown Supply Current | IS | 12 | 20 | µA | VEN < 0.3V | 3 | |
| Quiescent Supply Current | IQ | 140 | 200 | µA | No load, VFB = 0.9V (no switching) | 3 | |
| Thermal Shutdown | 150 | °C | Hysteresis = 20°C | 3 | |||
| Minimum Off Time | tOFF | 100 | ns | 3 | |||
| Minimum On Time | tON | 100 | ns | 3 | |||
| EN Rising Threshold | 1.4 | 1.55 | 1.7 | V | TJ=25°C | 3 | |
| EN Rising Threshold (over temperature) | 1.3 | 1.8 | V | 3 | |||
| EN Threshold Hysteresis | 320 | mV | 3 | ||||
| Supply Voltage | VIN | -0.3 | 60 | V | 2 | ||
| Switch Voltage | VSW | -0.5 | V | Max is VIN + 0.5V | 2 | ||
| BST to SW Voltage | -0.3 | 5 | V | 2 | |||
| All Other Pins Voltage | -0.3 | 5 | V | 2 | |||
| Continuous Power Dissipation | PD | 2.5 | W | TJ = +25°C, SOIC8E | 2 | ||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Storage Temperature | TSTG | -65 | 150 | °C | 2 | ||
| Supply Voltage | VIN | 3.8 | 55 | V | 2 | ||
| Output Voltage | VOUT | 0.8 | 52 | V | 2 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | 2 | ||
| Junction-to-Case Thermal Resistance | θJC | 10 | °C/W | SOIC8 (Exposed Pad) | 2 |
CAD (KiCad official)
- Symbol:
MP4558DN-LF-Z - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
mp4558dn-lf-z-etched.step/mp4558dn-lf-z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mp4558dn-lf-z.step/mp4558dn-lf-z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Monolithic Power Systems datasheet (20 pp, sha256
e31e175dd5dd7381, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).