Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX22216ATJY+

ADI/MAXIM · Motor Driver ICs · TQFN-32-EP(5x5)

MAX22216ATJY+ from ADI/MAXIM, in a TQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IREF input Connect a 1% accurate 12kΩ resistor from IREF to GND to set the full-scale current for all channels in CDR mode; IREF is absolute-maximum rated to min(+2.2V, VDD+0.3V).
2 FAULT output Open-drain output pulled logic low on a fault condition and requires an external pullup resistor; FAULT is absolute-maximum rated to -0.3V to +6V.
3 STAT0 output Status logic output referenced to VIO that reports channel status selected by the STATUS_CFG settings.
4 STAT1 output Status logic output referenced to VIO that reports channel status selected by the STATUS_CFG settings.
5 GND power_in Signal ground that must be connected to the board ground.
6 VDD power_out 1.8V LDO regulator output that must be bypassed to GND with a 2.2μF ceramic capacitor; VDD is absolute-maximum rated to min(+2.2V, VM+0.3V).
7 CNTL0 input Control logic input with internal pulldown to GND that should be tied to GND if unused to avoid spurious triggering.
8 CNTL1 input Control logic input with internal pulldown to GND that should be tied to GND if unused to avoid spurious triggering.
9 CNTL2 input Control logic input with internal pulldown to GND that should be tied to GND if unused to avoid spurious triggering.
10 CNTL3 input Control logic input with internal pulldown to GND that should be tied to GND if unused to avoid spurious triggering.
11 CRC_EN input Logic input with internal pulldown to GND; driving it high enables cyclic redundancy check on SPI communication.
12 CFN passive Charge pump capacitor N side; connect a 22nF, VM-rated ceramic capacitor from CFN to CFP.
13 CFP passive Charge pump capacitor P side; connect a 22nF, VM-rated ceramic capacitor from CFN to CFP.
14 VCP power_out Charge pump output; connect a 1μF, 5V or greater ceramic capacitor to VM.
15 VM power_in Supply voltage input (4.5V to 36V operating range) that must be shorted to the other VM pins on the board and bypassed with 0.1μF ceramic capacitors close to pins 21, 20, 26 and 15.
16 OUT3 output Driver output for channel 3 of the half-bridge stage.
17 PGND power_in Power ground; all PGND pins must be shorted on the board.
18 PGND power_in Power ground; all PGND pins must be shorted on the board.
19 OUT2 output Driver output for channel 2 of the half-bridge stage.
20 VM power_in Supply voltage input (4.5V to 36V operating range) that must be shorted to the other VM pins on the board.
21 VM power_in Supply voltage input (4.5V to 36V operating range) that must be shorted to the other VM pins on the board.
22 OUT1 output Driver output for channel 1 of the half-bridge stage.
23 PGND power_in Power ground; all PGND pins must be shorted on the board.
24 PGND power_in Power ground; all PGND pins must be shorted on the board.
25 OUT0 output Driver output for channel 0 of the half-bridge stage.
26 VM power_in Supply voltage input (4.5V to 36V operating range) that must be shorted to the other VM pins on the board.
27 ENABLE input VM-rated logic enable input with internal pulldown; driving it high enables the device and driving it low enters low-power sleep mode.
28 SCK input SPI clock input referenced to VIO with internal pulldown to GND; rising edge clocks data in for writes and falling edge clocks data out for reads.
29 CS input SPI chip select, active low, referenced to VIO with internal pullup current.
30 SDI input SPI data input from controller referenced to VIO with internal pulldown to GND.
31 SDO output SPI data output referenced to VIO.
32 VIO power_in I/O supply input (2.2V to 5.25V) when the internal linear regulator is disabled (EN_LDO=0); if EN_LDO=1 this pin becomes a 3.3V or 5V regulator output that needs at least a 0.47μF bypass capacitor.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer ADI/MAXIM
Package TQFN-32-EP(5x5)
Category Power Management ICs
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range VM 4.5 36 V 8
Logic Input Supply Voltage VIO 2.2 5.25 V 8
VM to GND -0.3 42 V VM to GND 8
VIO to GND -0.3 6 V VIO to GND 8
Operating Temperature Range TA -40 125 °C 8
Junction Temperature 150 °C 8
Storage Temperature Range -65 150 °C 8
Sleep Mode Current consumption ISLEEP 4 18 µA Enable logic low 8
Nap Mode Current Consumption INAP 210 450 µA Enable logic high, Active = 0 9
Quiescent Current Consumption IVM 7 9 mA Enable logic high, Active = 1 9
Enable Voltage Level High VIH(EN) 0.9 V 9
Enable Voltage Level Low VIL(EN) 0.6 V 9
Enable Pulldown Input Resistance RPD(EN) 0.8 1.5 MΩ 9
Logic Input Pin Pulldown Resistance RPD 70 100 130 kΩ To GND. Pins CNTL_, SCK, SDI, CRC_EN. 9
CS Pin Pullup Resistance RPU 70 100 130 kΩ To VIO 9
Logic-Low Output Voltage VOL 0.4 V ILOAD = 5mA, STAT_ and FAULT pin 9
Output On-Resistance Low Side SNSF 00 RON(LS) 0.17 0.33 Ω MAX22216, SNSF[1:0] = '00' 9
Output On-Resistance Low Side SNSF 01 RON(LS) 0.23 0.45 Ω MAX22216, SNSF[1:0] = '01' 9
Output On-Resistance Low Side SNSF 10 RON(LS) 0.43 0.83 Ω MAX22216, SNSF[1:0] = '10' 9
Output On-Resistance High Side RON(HS) 0.17 0.33 Ω 9
Output Leakage ILEAK -5 5 μA Driver OFF 9
Overcurrent Protection Blanking Time TOCP 1.45 2.1 2.85 μs 10
UVLO Threshold on VM Rising UVLO 3.75 4 4.25 V Rising 10
UVLO Threshold on VM Falling UVLO 3.88 4.12 V Falling 10
Thermal Protection Threshold Temperature TSD 165 °C 10
Open-Load Detection Current Pulldown IOL_LS 75 135 μA OL_EN_ = 1, HSnLS = 0, pulldown current 10
Open-Load Detection Current Pullup IOL_HS -50 -22 μA OL_EN_ = 1, HSnLS = 1, pullup current 10
Open-Load Detection Voltage Low Side VOL_LS 1.7 2.4 V OL_EN_ = 1, HSnLS = 0 10
Open-Load Detect Deglitch Time tOL 189 200 211 μs 10
VDD Regulator Output Voltage VVDD 1.868 V ILOAD = 20mA 10
VDD Current Limit IVDDLIM 20 mA 10
VIO Regulator Output Voltage 5V VVIO 4.8 5 5.2 V EN_LDO = 1, ILOAD = 10mA, V5nV3 = 1 10
VIO Regulator Output Voltage 3.3V VVIO 3.15 3.3 3.4 V EN_LDO = 1, ILOAD = 10mA, V5nV3 = 0 10
Internal Oscillator Frequency FCLK 23.7 25 26.3 MHz 10
CDR Maximum Full Scale LS or FB SNSF 00 IFSMAX 3.2 A MAX22216, GAIN[1:0] = '00', LS or FB config., SNSF[1:0] = '00' (Note 1) 10
CDR Maximum Full Scale LS or FB SNSF 01 IFSMAX 2.1 A MAX22216, GAIN[1:0] = '00', LS or FB config., SNSF[1:0] = '01' (Note 1) 10
CDR Maximum Full Scale LS or FB SNSF 10 IFSMAX 1 A MAX22216, GAIN[1:0] = '00', LS or FB config., SNSF[1:0] = '10' (Note 1) 10
CDR Maximum Full Scale HS SNSF 00 IFSMAX 1.5 A MAX22216, GAIN[1:0] = '00', HS config., SNSF[1:0] = '00' (Note 1) 10
CDR Maximum Full Scale HS SNSF 01 IFSMAX 1 A MAX22216, GAIN[1:0] = '00', HS config., SNSF[1:0] = '01' (Note 1) 10
CDR Maximum Full Scale HS SNSF 10 IFSMAX 0.5 A MAX22216, GAIN[1:0] = '00', HS config., SNSF[1:0] = '10' (Note 1) 10
Current Control and Monitor Accuracy DCDR -5 5 % MAX22216, GAIN[1:0] = '00', IOUT >= 250mA, SNSF[1:0] = '00' 11
REF Pin Resistor Range RREF -5 5 % Nominal 12kΩ resistor (Note 2) 11
Disable Time tDIS 20 µs Enable falling edge to OUT_ tristated 11
Enable Time tEN 0.8 ms From enable logic-high to normal operation (Note 4) 11
SCK Clock Period VIO > 3V tCLK 100 ns VIO > 3V 11
SDI Setup Time before SCK Rising Edge tDS 10 ns 11
SDO Propagation Delay VIO > 3V tDO 40 ns CLOAD = 15pF, VIO > 3V 11
Junction to Ambient four-layer board θJA 29 °C/W Four-layer board, JESD51-7 8
Junction to Case θJC 1.7 °C/W Four-layer board, JESD51-7 8
Open-Load Detect Hysteresis TSD_HYST 20 °C Thermal protection temperature hysteresis 10
Dead Time tDEAD 0.1 µs 9
Slew-Rate Control SRC 00 SRC 800 V/µs SRC[1:0] = '00' 9
Overcurrent Protection Threshold SNSF 00 OCP 4 A SNSF[1:0] = '00' 9
CDR Constant KCDR MAX22216 KCDR 1.017 mA MAX22216 10
CDR Constant KCDR MAX22217 KCDR 0.339 mA MAX22217 10
VDR Constant KVDR 30.518 μV 11
Resistance Measurement Constant KR 8.437 mΩ 11
Supply Voltage Monitoring Constant KVM 9.73 mV 11

CAD (KiCad official)

  • Symbol: MAX22216ATJY+
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: TQFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: max22216atjy-etched.step / max22216atjy-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max22216atjy.step / max22216atjy.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ADI/MAXIM datasheet (82 pp, sha256 20f7a572c086e2c9, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF