component
FT1128Q
Public Made by Adomby adom
Fortior Tech Motor Driver ICs, QFN-28(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFT1128Q
Fortior Tech · Motor Driver ICs · QFN-28(5x5)
FT1128Q from Fortior Tech, in a QFN-28(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Power supply, with recommended Vcc of 3.7 V to 28 V (12 V typical) and absolute maximum of 30.0 V. |
| 2 | VSS | power_in | Signal and power ground. |
| 3 | VDD5 | power_out | Digital power output from the LDO, regulated at 4.9 V to 5.1 V for digital signals with output current up to 10 mA. |
| 4 | RPI | input | Soft start duty setting input. |
| 5 | VDC_DETE | input | Power supply over voltage and under voltage detection input; all MOS are turned off above 3.9 V or below 1.2 V. |
| 6 | BRAKE | input | Brake signal input with internal pull-up, where a low level brakes the motor. |
| 7 | SPEED/PWM | input | Speed control input for digital PWM or analog voltage, with high-level input 2.7 V to 5.3 V and low-level input 0 V to 0.9 V. |
| 8 | FR | input | Motor rotation direction input. |
| 9 | ILIMIT | input | Current limit analog input. |
| 10 | RD | output | Open drain motor rotate detection output, with withstand voltage of 5.5 V max and output current of 10 mA max. |
| 11 | FG | output | Open drain frequency generator speed signal output that requires an external pull-up resistor when used. |
| 12 | FG2 | output | Open drain frequency generator output carrying the Hall B signal. |
| 13 | TDA | input | Thermal detection input; external thermal protection is triggered when TDA is below 2.12 V. |
| 14 | HC_INN | input | Hall C negative sensor input for phase W magnetic field detection, with zero-peak sensitivity of 10 mV to 20 mV. |
| 15 | HC_INP | input | Hall C positive sensor input for phase W magnetic field detection, with zero-peak sensitivity of 10 mV to 20 mV. |
| 16 | HB_INN | input | Hall B negative sensor input for phase V magnetic field detection, with zero-peak sensitivity of 10 mV to 20 mV. |
| 17 | HB_INP | input | Hall B positive sensor input for phase V magnetic field detection, with zero-peak sensitivity of 10 mV to 20 mV. |
| 18 | HA_INN | input | Hall A negative sensor input for phase U magnetic field detection, with zero-peak sensitivity of 10 mV to 20 mV. |
| 19 | HA_INP | input | Hall A positive sensor input for phase U magnetic field detection, with zero-peak sensitivity of 10 mV to 20 mV. |
| 20 | ISENSE | input | Current limit and lead angle analog input, with analog input range of 0 V to 5.3 V. |
| 21 | ITRIP | input | Current limit and over current protection input, with over current threshold typically 0.5 V. |
| 22 | WL | output | Low side phase W NMOS driver output. |
| 23 | VL | output | Low side phase V NMOS driver output. |
| 24 | UL | output | Low side phase U NMOS driver output. |
| 25 | WH | output | High side phase W PMOS driver output. |
| 26 | VH | output | High side phase V PMOS driver output. |
| 27 | UH | output | High side phase U PMOS driver output. |
| 28 | VREG10 | output | LDO output regulated at 9.5 V to 10.5 V. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Fortior Tech |
| Package | QFN-28(5x5) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage (absolute maximum) | Vccmax | 30 | V | 4 | |||
| RD/FG output current | IRDFGmax | 10 | mA | 4 | |||
| RD/FG output pin withstand voltage | VRDFG max | 5.5 | V | 4 | |||
| Operating temperature | Topr | -40 | 125 | ℃ | 4 | ||
| Storage temperature | Tstg | -65 | 150 | ℃ | 4 | ||
| Power supply voltage (recommended operating) | Vcc | 3.7 | 12 | 28 | V | 4 | |
| Power supply current | Icc | 10 | 15 | mA | Working | 5 | |
| VDD5 LDO regulator voltage | VDD5 | 4.9 | 5 | 5.1 | V | 5 | |
| VDD5 LDO regulator output current | Iv5out | 10 | mA | VDD5=5V | 5 | ||
| 10V regulator voltage | Vreg10 | 9.5 | 10 | 10.5 | V | 5 | |
| 10V regulator output current | Iv10out | 10 | mA | Vreg10=10V | 5 | ||
| Analog input range | 0 | 5.3 | V | 5 | |||
| Hall sensor input sensitivity | VHN | 10 | 20 | mV | Zero peak value (including offset and hysteresis) | 5 | |
| High-level input voltage | Vdinh | 2.7 | 5.3 | V | 5 | ||
| Low-level input voltage | Vdinl | 0 | 0.9 | V | 5 | ||
| PWM input frequency | Fpwm | 1 | 80 | kHz | 5 | ||
| High-side PMOS driver (UH/VH/WH) output high voltage | HVoh | 11.2 | 11.5 | 12 | V | Sink current = 20mA | 5 |
| High-side PMOS driver (UH/VH/WH) output low voltage | HVol | 3 | 5 | V | Source current = 20mA | 5 | |
| Low-side NMOS driver (UL/VL/WL) output high voltage | LVoh | 8.5 | 10 | 11 | V | Sink current = 20mA | 5 |
| Low-side NMOS driver (UL/VL/WL) output low voltage | LVol | 0 | 0.3 | V | Source current = 20mA | 5 | |
| RD/FG/FG2 output pin low-level voltage | VRD_FG | 0.1 | 0.2 | V | When Io=5mA | 5 |
CAD (KiCad official)
- Symbol:
FT1128Q - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: QFN-28(5x5) (KiCad packages3D, STEP)
- 3D model files:
ft1128q-etched.step/ft1128q-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft1128q.step/ft1128q.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Fortior Tech datasheet (16 pp, sha256
22c1f369fb4a79bf, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).