3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLMK01010ISQ
Texas Instruments · Clock Buffers, Drivers · WQFN-48-EP(7x7)
LMK01010ISQ from Texas Instruments, in a WQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; connect to the system ground plane. |
| 2 | NC | unconnected | No connect; the pin is not connected to the die. |
| 3 | Vcc1 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 4 | CLKuWire | input | MICROWIRE clock input for register programming, which is clocked on the rising edge (MSB first). |
| 5 | DATAuWire | input | MICROWIRE data input for register programming; data bits are shifted into the register on each CLKuWire rising edge. |
| 6 | LEuWire | input | MICROWIRE latch enable input; data is transferred to the addressed register on its rising edge. |
| 7 | NC | unconnected | No connect; the pin is not connected to the die. |
| 8 | Vcc2 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 9 | NC | unconnected | No connect; the pin is not connected to the die. |
| 10 | NC | unconnected | No connect; the pin is not connected to the die. |
| 11 | GOE | input | Global Output Enable; pulling it low disables all clock outputs, and it has an internal pull-up resistor. |
| 12 | Test | output | Test output that should be left not connected for normal operation; any load with an impedance above 1 kΩ is acceptable. |
| 13 | Vcc3 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 14 | CLKout0 | output | True side of clock output 0; for the LMK01010 this output is LVDS and it is enabled through CLKout0_EN and GOE. |
| 15 | CLKout0* | output | Complementary side of clock output 0; for the LMK01010 this output is LVDS. |
| 16 | Vcc4 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 17 | CLKout1 | output | True side of clock output 1; for the LMK01010 this output is LVDS. |
| 18 | CLKout1* | output | Complementary side of clock output 1; for the LMK01010 this output is LVDS. |
| 19 | Vcc5 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 20 | CLKout2 | output | True side of clock output 2; for the LMK01010 this output is LVDS. |
| 21 | CLKout2* | output | Complementary side of clock output 2; for the LMK01010 this output is LVDS. |
| 22 | Vcc6 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 23 | CLKout3 | output | True side of clock output 3; for the LMK01010 this output is LVDS. |
| 24 | CLKout3* | output | Complementary side of clock output 3; for the LMK01010 this output is LVDS. |
| 25 | GND | power_in | Ground pin; connect to the system ground plane. |
| 26 | Vcc7 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 27 | SYNC* | input | Global clock output synchronization; holding it low holds the divided outputs low, and it has an internal pull-up resistor. |
| 28 | CLKin0 | input | CLKin0 input (clock input 0); it must be AC coupled. |
| 29 | CLKin0* | input | Complementary CLKin0 input; it must be AC coupled. |
| 30 | Vcc8 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 31 | Vcc9 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 32 | NC | unconnected | No connect; the pin is not connected to the die. |
| 33 | Vcc10 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 34 | CLKin1 | input | CLKin1 input (clock input 1); it must be AC coupled. |
| 35 | CLKin1* | input | Complementary CLKin1 input; it must be AC coupled. |
| 36 | Bias | input | Bias bypass pin; it should be bypassed to Vcc with a low leakage 1 µF capacitor for low noise performance. |
| 37 | Vcc11 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 38 | CLKout4 | output | True side of clock output 4; for the LMK01010 this output is LVDS. |
| 39 | CLKout4* | output | Complementary side of clock output 4; for the LMK01010 this output is LVDS. |
| 40 | Vcc12 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 41 | CLKout5 | output | True side of clock output 5; for the LMK01010 this output is LVDS. |
| 42 | CLKout5* | output | Complementary side of clock output 5; for the LMK01010 this output is LVDS. |
| 43 | Vcc13 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 44 | CLKout6 | output | True side of clock output 6; for the LMK01010 this output is LVDS. |
| 45 | CLKout6* | output | Complementary side of clock output 6; for the LMK01010 this output is LVDS. |
| 46 | Vcc14 | power_in | Power supply pin; the supply range is 3.15 V to 3.45 V (3.3 V typical), and all Vcc pins should be applied simultaneously. |
| 47 | CLKout7 | output | True side of clock output 7; for the LMK01010 this output is LVDS. |
| 48 | CLKout7* | output | Complementary side of clock output 7; for the LMK01010 this output is LVDS. |
| 49 | DAP | power_in | Die attach (exposed thermal) pad; it should be connected to ground and soldered to the PCB for heat removal. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-48-EP(7x7) |
| Category | RTC/Clock Chip |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Voltage | VCC | -0.3 | 3.6 | V | 4 | ||
| Input Voltage | VIN | -0.3 | V | Maximum printed as (VCC + 0.3) V | 4 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| Lead Temperature | TL | 260 | °C | Solder 4 s | 4 | ||
| Junction Temperature | TJ | 125 | °C | 4 | |||
| Ambient Temperature | TA | -40 | 25 | 85 | °C | 4 | |
| Power Supply Voltage | VCC | 3.15 | 3.3 | 3.45 | V | 4 | |
| Thermal resistance, junction to ambient (48-Lead LLP) | θJA | 27.4 | °C/W | Specification assumes 16 thermal vias on 4-layer JEDEC board | 5 | ||
| Thermal resistance, junction to thermal pad (48-Lead LLP) | θJ-PAD | 5.8 | °C/W | Specification assumes 16 thermal vias on 4-layer JEDEC board | 5 | ||
| CLKin Frequency Range | fCLKin | 1 | 1600 | MHz | 6 | ||
| CLKin Frequency Input Duty Cycle | DUTYCLKin | 30 | 70 | % | fCLKin ≤ 800 MHz | 6 | |
| CLKin Frequency Input Duty Cycle | DUTYCLKin | 40 | 60 | % | fCLKin > 800 MHz | 6 | |
| Input Power Range for CLKin or CLKin* | PCLKin | -13 | 5 | dBm | AC coupled | 6 | |
| Maximum Allowable Delay | DelayCLKout | 2250 | ps | fCLKoutX ≤ 1 GHz; delay limited to maximum programmable value | 6 | ||
| Allowable divide range | DivideCLKoutX | 1 | 510 | fCLKinX ≤ 1300 MHz | 6 | ||
| CLKoutX to CLKoutY skew (LVDS) | tSKEW | -30 | 4 | 30 | ps | Equal loading and identical clock configuration | 7 |
| Differential Output Voltage (LVDS) | VOD | 250 | 350 | 450 | mV | RL = 100 Ω, Vboost=0 | 7 |
| Change in magnitude of VOD for complementary output states | ΔVOD | -50 | 50 | mV | RL = 100 Ω | 7 | |
| Output Offset Voltage | VOS | 1.07 | 1.25 | 1.37 | V | RL = 100 Ω | 7 |
| Change in magnitude of VOS for complementary output states | ΔVOS | -35 | 35 | mV | RL = 100 Ω | 7 | |
| Clock Output Short Circuit Current (single ended) | ISA, ISB | -24 | 24 | mA | Single ended outputs shorted to GND | 7 | |
| Clock Output Short Circuit Current (differential) | ISAB | -12 | 12 | mA | Complementary outputs tied together | 7 | |
| CLKoutX to CLKoutY skew (LVPECL) | tSKEW | -30 | 3 | 30 | ps | Equal loading and identical clock configuration; Termination = 50 Ω to Vcc - 2 V | 7 |
| Differential Output Voltage (LVPECL) | VOD | 660 | 810 | 965 | mV | Vboost = 0 | 7 |
| High-Level Input Voltage (LVTTL) | VIH | 2 | V | Applies to GOE, LD, and SYNC* | 7 | ||
| High-Level Input Current (LVTTL) | IIH | -5 | 5 | µA | VIH = Vcc | 7 | |
| Low-Level Input Current (LVTTL) | IIL | -40 | 5 | µA | VIL = 0 | 7 | |
| High-Level Input Voltage (MICROWIRE) | VIH | 1.6 | V | Applies to CLKuWire, DATAuWire, and LEuWire | 8 | ||
| High-Level Input Current (MICROWIRE) | IIH | -5 | 5 | µA | VIH = Vcc | 8 | |
| Low-Level Input Current (MICROWIRE) | IIL | -5 | 5 | µA | VIL = 0 | 8 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 48-Lead LLP (1) 27.4° C/W 5.8° C/W (1) Specification assumes 16 thermal vias connect the die attach pad to the embedded copper plane on the 4-layer JEDEC board. These | 5 |
CAD (KiCad official)
- Symbol:
LMK01010ISQ - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: WQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
lmk01010isq-etched.step/lmk01010isq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmk01010isq.step/lmk01010isq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (28 pp, sha256
8f668476c4ca1696, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).