Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM26480QSQ-CF

Texas Instruments · DC-DC Converters · WQFN-24-EP(4x4)

LM26480QSQ-CF from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VINLDO12 power_in Analog power for internal functions (VREF, BIAS, I2C, Logic).
2 SYNC input Frequency synchronization pin that allows an external clock to synchronize the internal oscillator; default OFF and must be grounded when not used.
3 NPOR output Open-drain nPOR power-on reset output for Buck1 and Buck2 with a 100-kΩ pullup, pulled to ground when these supplies are not good.
4 GND_SW1 power_in Buck1 NMOS power ground.
5 SW1 power_out Buck1 switcher output pin.
6 VIN1 power_in Power input from DC source or battery to Buck1.
7 ENSW1 input Enable pin for Buck1; a logic HIGH enables Buck1 and the pin cannot be left floating.
8 FB1 input Buck1 input feedback terminal.
9 GND_C power_in Non-switching core ground pin.
10 AVDD power_in Analog power for Buck converters.
11 FB2 input Buck2 input feedback terminal.
12 ENSW2 input Enable pin for Buck2; a logic HIGH enables Buck2 and the pin cannot be left floating.
13 VIN2 power_in Power input from DC source or battery to Buck2.
14 SW2 power_out Buck2 switcher output pin.
15 GND_SW2 power_in Buck2 NMOS power ground.
16 ENLDO2 input LDO2 enable pin; a logic HIGH enables LDO2 and the pin cannot be left floating.
17 ENLDO1 input LDO1 enable pin; a logic HIGH enables LDO1 and the pin cannot be left floating.
18 GND_L power_in LDO ground.
19 VINLDO1 power_in Power input from DC source or battery to LDO1.
20 LDO1 power_out LDO1 output.
21 FBL1 input LDO1 feedback terminal.
22 FBL2 input LDO2 feedback terminal.
23 LDO2 power_out LDO2 output.
24 VINLDO2 power_in Power input from DC source or battery to LDO2.
25 DAP power_in Connection is not necessary for electrical performance but is recommended for better thermal dissipation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-24-EP(4x4)
Category Power Supply Chip
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operational voltage range VINLDO1 and VINLDO2 1.74 5.5 V TJ = −40°C to 125°C 6
Input voltage VIN (Bucks) VIN 2.8 5.5 V 5
Junction temperature TJ -40 125 °C 5
Ambient temperature TA -40 125 °C 5
Absolute maximum voltage on VINLDO12, VIN1, AVDD, VIN2, VINLDO1, VINLDO2, ENSW1, FB1, FB2, ENSW2, ENLDO1, ENLDO2, SYNC, FBL1, FBL2 -0.3 6 V Voltages with respect to GND 5
GND to GND SLUG -0.3 0.3 V 5
Power dissipation PD_MAX PD_MAX 1.17 W TA = 85°C, TMAX = 125°C 5
Junction temperature TJ-MAX TJ-MAX 150 °C 5
Storage temperature Tstg -65 150 °C 5
FB voltage accuracy (LDO) VFB -3 3 % TJ = −40°C to 125°C 6
Feedback voltage (Buck) VFB -3 3 % 7
Dropout voltage VIN, VOUT 25 mV Load current = 50 mA 6
Dropout voltage VIN, VOUT 200 mV TJ = −40°C to 125°C 6
Line regulation (LDO) ΔVOUT 0.15 %/V VIN = (VOUT + 0.3 V) to 5 V; Load current = 1 mA; TJ = −40°C to 125°C 6
Load regulation (LDO) ΔVOUT 0.011 %/mA VIN = 3.6 V, TJ = −40°C to 125°C; Load current = 1 mA to IMAX 6
Quiescent current on (LDO) IQ 40 µA IOUT = 0 mA 6
Quiescent current on (LDO) IQ 150 µA IOUT = 0 mA, −40°C ≤ TJ ≤ 125°C 6
Quiescent current on (LDO) IQ 60 µA IOUT = 300 mA 6
Quiescent current on (LDO) IQ 200 µA IOUT = 300 mA, −40°C ≤ TJ ≤ 125°C 6
Quiescent current off (LDO) IQ 0.03 1 µA EN is de-asserted 6
Output capacitor (LDO) capacitance for stability COUT 0.33 µF −40°C ≤ TJ ≤ 125°C 7
Output capacitor (LDO) ESR ESR 5 500 mΩ TJ = −40°C to 125°C 7
Shutdown supply current (VINLDO12) IQ 0.5 µA VIN = 3.6 V 6
Line regulation (Buck) VOUT 0.089 %/V 2.8 V < VIN < 5.5 V; IOUT = 10 mA 7
Load regulation (Buck) VOUT 0.0013 %/mA 100 mA < IOUT < IMAX 7
Internal oscillator frequency (default 2.1 MHz) ƒOSC 2.1 2.5 MHz Default oscillator frequency = 2.1 MHz 7
Internal oscillator frequency (default 2.1 MHz) ƒOSC 1.7 MHz Default oscillator frequency = 2.1 MHz, TJ = −40°C to 125°C 7
Buck1 peak switching current limit IPEAK 2 2.4 A 7
Buck2 peak switching current limit IPEAK 2 2.4 A 7
Shutdown supply current (Buck) ISHDN 0.01 1 µA EN is de-asserted 7
Quiescent current on (Buck), PFM mode IQ 33 µA No load PFM mode 7
Quiescent current on (Buck), PWM mode IQ 2 mA No load PWM mode (forced PWM) 7
Pin-pin resistance PFET RDSON(P) 200 400 mΩ 7
Pin-pin resistance NFET RDSON(N) 180 400 mΩ 7
Efficiency Eff 96 % Load current = 250 mA 7
Input capacitor CIN CIN 10 µF Capacitance for stability 7
Output capacitor COUT COUT 10 µF Capacitance for stability 7
Input low level VIL 0.4 V 8
Output level low VOL 0.23 0.5 V Load = IOL = 500 µA 8
nPOR power-on reset delay (default) 60 ms Default = 60 ms 8
Junction-to-ambient thermal resistance RθJA 32.7 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 31.2 °C/W 5
Junction-to-board thermal resistance RθJB 11.2 °C/W 5
Junction-to-top characterization parameter ψJT 0.2 °C/W 5
Junction-to-board characterization parameter ψJB 11.2 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 0.4 °C/W 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 3. Connect the ground pins of the buck, and filter capacitors together using generous component-side copper 31

CAD (KiCad official)

  • Symbol: LM26480QSQ-CF
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lm26480qsq-cf-etched.step / lm26480qsq-cf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm26480qsq-cf.step / lm26480qsq-cf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet, copy hosted by LCSC (41 pp, sha256 4f0d00e132e01d5c, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF