3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownESP32-DevKitM-1
Espressif Systems · development board · ESP32-MINI-1
This page carries the board as a part, so a carrier board or a breakout molecule can place it: the header pinout as a symbol, the header pattern as a footprint, and a 3D model of the board standing on its headers.
Footprint
J1 (17 pins) and J3 (17 pins) at 2.54 mm, from Espressif's dimension drawing. The footprint origin is the centre of the header pattern; F.Fab draws the board (25.40 x 43.81 mm) and the module. The module's antenna runs 5.48 mm past the board edge; the footprint keeps copper out from under that overhang.
Pinout
As printed in Espressif's user guide (current revision). Pin 1 of each header is at the module end.
J1
| No. | Name | Function |
|---|---|---|
| 1 | GND | Ground |
| 2 | 3V3 | 3.3 V power supply |
| 3 | I36 | GPIO36, ADC1_CH0, RTC_GPIO0 |
| 4 | I37 | GPIO37, ADC1_CH1, RTC_GPIO1 |
| 5 | I38 | GPIO38, ADC1_CH2, RTC_GPIO2 |
| 6 | I39 | GPIO39, ADC1_CH3, RTC_GPIO3 |
| 7 | RST | Reset; High: enable; Low: powers off |
| 8 | I34 | GPIO34, ADC1_CH6, RTC_GPIO4 |
| 9 | I35 | GPIO35, ADC1_CH7, RTC_GPIO5 |
| 10 | IO32 | GPIO32, XTAL_32K_P (32.768 kHz crystal oscillator input), ADC1_CH4, TOUCH9, RTC_GPIO9 |
| 11 | IO33 | GPIO33, XTAL_32K_N (32.768 kHz crystal oscillator output), ADC1_CH5, TOUCH8, RTC_GPIO8 |
| 12 | IO25 | GPIO25, DAC_1, ADC2_CH8, RTC_GPIO6, EMAC_RXD0 |
| 13 | IO26 | GPIO26, DAC_2, ADC2_CH9, RTC_GPIO7, EMAC_RXD1 |
| 14 | IO27 | GPIO27, ADC2_CH7, TOUCH7, RTC_GPIO17, EMAC_RX_DV |
| 15 | IO14 | GPIO14, ADC2_CH6, TOUCH6, RTC_GPIO16, MTMS, HSPICLK, HS2_CLK, SD_CLK, EMAC_TXD2 |
| 16 | 5V | 5 V power supply |
| 17 | GND | Ground |
J3
| No. | Name | Function |
|---|---|---|
| 18 | IO12 | GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3 |
| 19 | IO13 | GPIO13, ADC2_CH4, TOUCH4, RTC_GPIO14, MTCK, HSPID, HS2_DATA3, SD_DATA3, EMAC_RX_ER |
| 20 | IO15 | GPIO15, ADC2_CH3, TOUCH3, RTC_GPIO13, MTDO, HSPICS0, HS2_CMD, SD_CMD, EMAC_RXD3 |
| 21 | IO2 | GPIO2, ADC2_CH2, TOUCH2, RTC_GPIO12, HSPIWP, HS2_DATA0, SD_DATA0 |
| 22 | IO0 | GPIO0, ADC2_CH1, TOUCH1, RTC_GPIO11, CLK_OUT1, EMAC_TX_CLK |
| 23 | IO4 | GPIO4, ADC2_CH0, TOUCH0, RTC_GPIO10, HSPIHD, HS2_DATA1, SD_DATA1, EMAC_TX_ER |
| 24 | IO9 | GPIO9, HS1_DATA2, U1RXD, SD_DATA2 |
| 25 | IO10 | GPIO10, HS1_DATA3, U1TXD, SD_DATA3 |
| 26 | IO5 | GPIO5, HS1_DATA6, VSPICS0, EMAC_RX_CLK |
| 27 | IO18 | GPIO18, HS1_DATA7, VSPICLK |
| 28 | IO23 | GPIO23, HS1_STROBE, VSPID |
| 29 | IO19 | GPIO19, VSPIQ, U0CTS, EMAC_TXD0 |
| 30 | IO22 | GPIO22, VSPIWP, U0RTS, EMAC_TXD1 |
| 31 | IO21 | GPIO21, VSPIHD, EMAC_TX_EN |
| 32 | RXD0 | GPIO3, U0RXD, CLK_OUT2 |
| 33 | TXD0 | GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2 |
| 34 | GND | Ground |
3D model
Rebuilt from Espressif's own manufacturing data: the PCB layout plots (PCB_ESP32-DevKitM-1_V1_20200910AE.pdf) give every part, its pads (by the plot's own pad designators) and the silkscreen as Espressif drew them; the dimension DXF (ESP32-DevKitM-1_V1.dxf) gives the outline and drills. The module is Espressif's ESP32-MINI-1 model (espressif/kicad-libraries) with its name etched; every other part is a KiCad library model fitted to its pads in the plot (worst fit 0.07 mm), each listed below with where its model came from. J2: Micro-B jack with no maker datasheet, generated from the USB Micro-B receptacle interface and the jack height in Espressif's BOM (S3-DevKitC-1 reference design, USB_5P_MICRO_F_ML), on this board's own land. The headers are mounted below the board, pins down, as the kit ships. Solder mask black and silkscreen white, from Espressif's user-guide photo. Two-pad parts are fitted by their land: where a diode and an LED share a land, the land cannot tell which, and the passive values are not read from the schematic.
Documents
- User guide (Espressif, web)
- Module datasheet (ESP32-MINI-1, v1.8): docs/esp32-devkitm-1-module-esp32-mini-1-datasheet.pdf, from Espressif
- Schematic: docs/esp32-devkitm-1-schematic.pdf, from Espressif
Modules: schematic: ESP32-MINI-1.
Schematic (Espressif)
Parts on the board
| Ref | Part | Page | 3D model |
|---|---|---|---|
| C1 | (none) | KiCad library model, fitted to its plotted pads | |
| C2 | (none) | KiCad library model, fitted to its plotted pads | |
| C6 | (none) | KiCad library model, fitted to its plotted pads | |
| C7 | (none) | KiCad library model, fitted to its plotted pads | |
| C8 | (none) | KiCad library model, fitted to its plotted pads | |
| C9 | (none) | KiCad library model, fitted to its plotted pads | |
| C10 | (none) | KiCad library model, fitted to its plotted pads | |
| C11 | (none) | KiCad library model, fitted to its plotted pads | |
| C12 | (none) | KiCad library model, fitted to its plotted pads | |
| C13 | (none) | KiCad library model, fitted to its plotted pads | |
| C14 | (none) | KiCad library model, fitted to its plotted pads | |
| D1 | (none) | KiCad library model, fitted to its plotted pads | |
| D2 | (none) | KiCad library model, fitted to its plotted pads | |
| D3 | (none) | KiCad library model, fitted to its plotted pads | |
| D4 | (none) | KiCad library model, fitted to its plotted pads | |
| D5 | (none) | KiCad library model, fitted to its plotted pads | |
| J1 | (none) | KiCad library model, fitted to its plotted pads | |
| J2 | (none) | generated: USB Micro-B receptacle interface + Espressif BOM jack height (S3-DevKitC-1 reference design item 16, USB_5P_MICRO_F_ML), on this board's own land | |
| J3 | (none) | KiCad library model, fitted to its plotted pads | |
| Q1 | (none) | KiCad library model, fitted to its plotted pads | |
| Q2 | (none) | KiCad library model, fitted to its plotted pads | |
| R5 | (none) | KiCad library model, fitted to its plotted pads | |
| R10 | (none) | KiCad library model, fitted to its plotted pads | |
| R11 | (none) | KiCad library model, fitted to its plotted pads | |
| R12 | (none) | KiCad library model, fitted to its plotted pads | |
| R14 | (none) | KiCad library model, fitted to its plotted pads | |
| R16 | (none) | KiCad library model, fitted to its plotted pads | |
| R18 | (none) | KiCad library model, fitted to its plotted pads | |
| R19 | (none) | KiCad library model, fitted to its plotted pads | |
| R21 | (none) | KiCad library model, fitted to its plotted pads | |
| R22 | (none) | KiCad library model, fitted to its plotted pads | |
| SW1 | (none) | KiCad library model, fitted to its plotted pads | |
| SW2 | (none) | KiCad library model, fitted to its plotted pads | |
| U2 | (none) | KiCad library model, fitted to its plotted pads | |
| U3 | (none) | KiCad library model, fitted to its plotted pads | |
| U4 | (none) | Espressif's ESP32-MINI-1 model (espressif/kicad-libraries), name etched |