3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHX3078-S
ZHHXDZ · RS-485 / RS-422 ICs · SOP-8
HX3078-S from ZHHXDZ, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: driven high when V(A)-V(B) is at or above -50mV and driven low when V(A)-V(B) is at or below -200mV. |
| 2 | RE | input | Receiver output enable, active low: a high level turns the receiver off, and when RE is high with DE low the whole chip is in shutdown. |
| 3 | DE | input | Driver output enable, active high: when DE is high the driver output is enabled, and when DE is low the driver turns off and the output enters a high-impedance state. |
| 4 | DI | input | Driver data input: when DI is high, A is driven high and B low; when DI is low, A is driven low and B high (with DE high). |
| 5 | GND | power_in | Ground reference for the device. |
| 6 | A | bidirectional | Bus line A (non-inverting driver output and receiver input), protected to ±15kV human-body-model ESD; receiver common-mode range is -7V to +12V. |
| 7 | B | bidirectional | Bus line B (inverting driver output and receiver input), protected to ±15kV human-body-model ESD; receiver common-mode range is -7V to +12V. |
| 8 | VCC | power_in | Supply voltage pin; the datasheet lists a 3.3V/5V supply, with DC characteristics tested at 3.3V ±5% and an absolute maximum of +6.0V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ZHHXDZ |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 6 | V | 2 | |||
| Control input voltage | DE, RE | -0.3 | 6 | V | 2 | ||
| Driver input voltage | DI | -0.3 | 6 | V | 2 | ||
| Driver output / receiver input voltage | A, B | -8 | 13 | V | 2 | ||
| Storage temperature range | TSTG | -65 | 150 | ℃ | 2 | ||
| Operating temperature range | TOP | -40 | 125 | ℃ | 2 | ||
| Power dissipation | PD | 471 | mW | SOP-8 (above 70 ℃) | 2 | ||
| Soldering temperature | 300 | ℃ | 10 seconds | 2 | |||
| Supply voltage (DC characteristics test condition) | VCC | 3.3 | V | Vcc=+3.3V±5%, TA=25℃ | 2 | ||
| Input high level | VIH1 | 2 | V | 2 | |||
| Input low level | VIL1 | 0.8 | V | 2 | |||
| Receiver output low voltage | VOL | 0.4 | V | IO=4mA, VID=-1V | 2 | ||
| Receiver output short-circuit current | IOSR | -7 | 7 | mA | 0V≤VRO≤VCC | 2 | |
| Receiver input impedance | RIN | 96 | KΩ | -7V≤VCM≤+12V | 2 | ||
| Input current (A and B) | IIN4 | 125 | uA | DE=GND, VCC=GND or 5.25V, VIN=12V | 2 | ||
| Shutdown supply current | SHDN | 10 | uA | DE=GND, RE=Vcc | 2 | ||
| ESD protection, human body model (Pin A, Pin B) | -15 | 15 | KV | Pin A, Pin B; human body model | 2 |
CAD (KiCad official)
- Symbol:
HX3078-S - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
hx3078-s-etched.step/hx3078-s-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hx3078-s.step/hx3078-s.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ZHHXDZ datasheet (5 pp, sha256
6cb59205e2e0dc8d, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).