3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8609AEDDM#PBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT8609AEDDM#PBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series with this pin. |
| 2 | SW | output | Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin that powers the internal drivers and control circuits; maximum output current is 20mA, voltage varies between 2.8V and 3.5V, decouple with at least 1µF low-ESR ceramic, and do not load with external circuitry. |
| 4 | RT | passive | A resistor tied between RT and ground sets the switching frequency (200kHz to 2.2MHz operating range). |
| 5 | SYNC | input | External clock synchronization input: ground for low-ripple Burst Mode operation at low loads, tie to a clock to synchronize, leave floating for pulse-skipping mode, or tie to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum modulation. |
| 6 | FB | input | Feedback pin for the adjustable output part, regulated to 0.782V; connect the feedback resistor divider tap to this pin. |
| 7 | TR/SS | passive | Output tracking and soft-start pin; a voltage below 0.782V forces FB to follow it, an internal 2µA pull-up from INTVCC sets the output slew rate via a capacitor, and it is pulled to ground through 300Ω during shutdown and fault conditions. |
| 8 | PG | output | Open-drain power-good output that stays low until FB is within ±8.5% of the regulation voltage with no fault conditions, and is valid when VIN is above 3.2V. |
| 9 | VIN | power_in | Supplies current to the internal circuitry and the internal topside power switch from a 3.0V to 42V input and must be locally bypassed with the input capacitor placed close to the VIN and GND pins. |
| 10 | EN/UV | input | Enable and undervoltage input: the part is shut down when low and active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if shutdown is not used. |
| 11 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance (θJA = 45°C/W, θJC = 10°C/W). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.7 | 3 | 3.2 | V | 4 | ||
| VIN Quiescent Current | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 4 | ||
| VIN Quiescent Current | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V | 4 | ||
| VIN Current in Regulation | 46 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100μA | 4 | ||
| VIN Current in Regulation | 480 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 4 | ||
| Feedback Reference Voltage | 0.778 | 0.782 | 0.786 | V | VIN = 6V, ILOAD = 100mA | 4 | |
| Feedback Reference Voltage (over temperature, l) | 0.77 | 0.782 | 0.794 | V | VIN = 6V, ILOAD = 100mA | 4 | |
| Feedback Voltage Line Regulation | 0.004 | 0.02 | %/V | VIN = 4.0V to 40V | 4 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1.0V | 4 | ||
| Minimum On-Time | 45 | 75 | ns | ILOAD = 1.5A, SYNC = 0V | 4 | ||
| Minimum On-Time | 45 | 60 | ns | ILOAD = 1.5A, SYNC = 1.9V | 4 | ||
| Minimum Off Time | 90 | 130 | ns | 4 | |||
| Oscillator Frequency | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 0.5A | 5 | |
| Oscillator Frequency | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 0.5A | 5 | |
| Oscillator Frequency | 1.925 | 2 | 2.075 | MHz | RT = 18.2k, ILOAD = 0.5A | 5 | |
| Top Power NMOS Current Limit | 3.4 | 4.5 | 5.7 | A | 5 | ||
| SW Leakage Current | 15 | µA | VIN = 42V, VSW = 40V | 5 | |||
| EN/UV Pin Threshold | 0.99 | 1.05 | 1.11 | V | EN/UV Rising | 5 | |
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V | 5 | ||
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising | 5 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling | 5 | |
| PG Leakage | -200 | 200 | nA | VPG = 42V | 5 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 5 | ||
| Sync Low Input Voltage | 0.4 | 0.9 | V | 5 | |||
| Sync High Input Voltage | 2.7 | 3.2 | V | INTVCC = 3.5V | 5 | ||
| TR/SS Source Current | 1 | 2 | 3 | µA | 5 | ||
| TR/SS Pull-Down Resistance | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V | 5 | ||
| Spread Spectrum Modulation Frequency | 1 | 3 | 6 | kHz | VSYNC = 3.3V | 5 | |
| FB, TR/SS pin voltage | 4 | V | 2 | ||||
| SYNC pin voltage | 6 | V | 2 | ||||
| Operating Junction Temperature Range | -40 | 125 | °C | LT8609AE grade | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient (DDM package) | θJA | 45 | °C/W | DDM package | 2 | ||
| Thermal Resistance Junction-to-Case (DDM package) | θJC | 10 | °C/W | DDM package | 2 |
CAD (KiCad official)
- Symbol:
LT8609AEDDM#PBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt8609aeddm-pbf-etched.step/lt8609aeddm-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8609aeddm-pbf.step/lt8609aeddm-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
bb514bf594e97238, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).