Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SN65176BP

Texas Instruments · RS-485 / RS-422 ICs · PDIP-8

SN65176BP from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 R output Logic data output from the RS-485 receiver.
2 RE input Receiver enable, active low.
3 DE input Driver enable, active high.
4 D input Logic data input to the RS-485 driver.
5 GND power_in Device ground pin.
6 A bidirectional RS-422 or RS-485 data line, non-inverting bus terminal.
7 B bidirectional RS-422 or RS-485 data line, inverting bus terminal.
8 VCC power_in Power input, connect to a 5V supply; recommended supply range is 4.75 V to 5.25 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package PDIP-8
Category Interface
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 7 V 4
Voltage range at any bus terminal -10 15 V 4
Enable input voltage VI 5.5 V 4
Operating virtual junction temperature TJ 150 °C 4
Storage temperature range Tstg -65 150 °C 4
Lead temperature 260 °C 1.6mm (1/16 inch) from case for 10 seconds 4
Supply voltage VCC 4.75 5 5.25 V 4
Voltage at any bus terminal (separately or common mode) VI or VIC -7 12 V 4
High-level input voltage VIH 2 V D, DE, and RE 4
Low-level input voltage VIL 0.8 V D, DE, and RE 4
Differential input voltage VID -12 12 V 4
High-level output current IOH -60 mA Driver 4
High-level output current IOH -400 µA Receiver 4
Low-level output current IOL 60 mA Driver 4
Low-level output current IOL 8 mA Receiver 4
Operating free-air temperature TA -40 105 °C SN65176B 4
Input clamp voltage VIK -1.5 V II = -18mA 5
Output voltage VO 0 V IO = 0 5
Differential output voltage /VOD1/ 1.5 3.6 V IO = 0 5
Differential output voltage /VOD2/ 2 V RL = 100Ω, see Figure 6-1 5
Differential output voltage /VOD2/ 1.5 2.5 5 V RL = 54Ω, see Figure 6-1 5
Differential output voltage /VOD3/ 1.5 5 V See (4) 5
Change in magnitude of differential output voltage Δ/VOD/ -0.2 0.2 V RL = 54Ω or 100Ω, see Figure 6-1 5
Common-mode output voltage VOC -1 3 V RL = 54Ω or 100Ω, see Figure 6-1 5
Change in magnitude of common-mode output voltage Δ/VOC/ -0.2 0.2 V RL = 54Ω or 100Ω, see Figure 6-1 5
Output current IO 1 mA Output disabled(6), VO = 12V 5
Output current IO -0.8 mA Output disabled(6), VO = -7V 5
High-level input current IIH 20 µA VI = 2.4V 5
Low-level input current IIL -400 µA VI = 0.4V 5
Short-circuit output current IOS -250 mA VO = -7V 5
Short-circuit output current IOS -150 mA VO = 0 5
Short-circuit output current IOS 250 mA VO = VCC 5
Supply current (total package) ICC 42 70 mA No load, Outputs enabled 5
Supply current (total package) ICC 26 35 mA No load, Outputs disabled 5
Positive-going input threshold voltage VIT+ 0.2 V VO = 2.7V, IO = -0.4mA 6
Negative-going input threshold voltage VIT- -0.2 V VO = 0.5V, IO = 8mA 6
Enable input clamp voltage VIK -1.5 V II = -18mA 6
High-level output voltage VOH 2.7 V VID = 200mV, IOH = -400µA, see Figure 6-2 6
Low-level output voltage VOL 0.45 V VID = -200mV, IOL = 8mA, see Figure 6-2 6
High-impedance-state output current IOZ -20 20 µA VO = 0.4V to 2.4V 6
Line input current II 1 mA Other input = 0V, VI = 12V 6
Line input current II -0.8 mA Other input = 0V, VI = -7V 6
High-level enable input current IIH 20 µA VIH = 2.7V 6
Low-level enable input current IIL -100 µA VIL = 0.4V 6
Input resistance rI 12 kΩ VI = 12V 6
Short-circuit output current IOS -85 -15 mA 6
Supply current (total package) ICC 42 55 mA No load, Outputs enabled 6
Supply current (total package) ICC 26 35 mA No load, Outputs disabled 6
Input hysteresis voltage (VIT+, VIT-) Vhys 50 mV 6
Junction-to-ambient thermal resistance RθJA 88.1 °C/W P (PDIP) package 4
Junction-to-case (top) thermal resistance RθJC(top) 65.9 °C/W P (PDIP) package 4
Junction-to-board thermal resistance RθJB 69 °C/W P (PDIP) package 4
Junction-to-top characterization parameter ψJT 35.2 °C/W P (PDIP) package 4
Junction-to-board characterization parameter ψJB 64.3 °C/W P (PDIP) package 4

CAD (KiCad official)

  • Symbol: SN65176BP
  • Footprint: Package_DIP:DIP-8_W7.62mm
  • 3D model: PDIP-8 (KiCad packages3D, STEP)
  • 3D model files: sn65176bp-etched.step / sn65176bp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sn65176bp.step / sn65176bp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (30 pp, sha256 6967824b2ea2d976, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF