Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PT4056

PUOLOP · Battery Management · ESOP-8

PT4056 from PUOLOP, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TEMP input Battery temperature sense input. Connect to the output of an NTC thermistor divider on the battery pack. Charging is paused when V(TEMP) falls below 45% of Vcc (over-temp) or rises above 80% of Vcc (under-temp). Tie TEMP directly to GND to disable temperature monitoring while leaving other charge functions active.
2 PROG passive Constant-current program and charge-current monitor pin. A resistor R_PROG from PROG to GND sets the fast-charge current: I_BAT = (V_PROG / R_PROG) × 1200, with V_PROG ≈ 1.0 V in constant-current mode (0.1 V during trickle). Pin voltage may be read to monitor instantaneous charge current. Max sink current 1200 µA; 2.0 µA internal pull-up.
3 GND power_in Device ground. Also serves as the thermal reference; connect the SOP-8 exposed pad to this net with a low-impedance copper pour to meet the 130 °C/W θJA assumed in the datasheet.
4 Vcc power_in Input supply from a USB port or wall adapter, 4.0 V typ 5 V max 6 V (abs-max −0.3 V to 7 V). Powers the internal circuitry and the pass FET (R_ON ≈ 650 mΩ). When (Vcc − V_BAT) drops below ≈30 mV the part enters low-power shutdown and the BAT pin sinks less than 2 µA. Decouple with 10 µF near the pin.
5 BAT power_out Charge current output to the positive terminal of the single-cell Li-ion / Li-polymer battery. Regulates to the 4.2 V float voltage (4.137-4.263 V) and delivers up to 1200 mA (abs-max) charge current. Leakage into the battery is <2 µA when the chip is disabled or in sleep. Auto-recharge triggers when V_BAT falls ≥150 mV below V_FLOAT.
6 STDBY output Open-drain charge-complete indicator (active-low, name is bar-STDBY). Internal switch pulls the pin low when the charge cycle terminates; otherwise Hi-Z. Typical V_OL = 0.2 V at 3 mA sink, abs-max 10 V. Drives an LED to GND through a series resistor, or leave floating if unused.
7 CHRG output Open-drain charge-in-progress indicator (active-low, name is bar-CHRG). Pulled low while the charger is delivering current to the battery; Hi-Z otherwise. With a 10 µF cap on BAT and no battery installed, pulses at ≈1-4 s to signal a missing battery. V_OL 0.2 V typ at 3 mA sink; abs-max 10 V.
8 CE input Chip enable input. Logic high enables normal charging; logic low disables the charger and inhibits current into BAT. TTL and CMOS compatible; abs-max −0.3 V to 10 V. Tie to Vcc for always-on operation.

Key specifications

Parameter Value
Manufacturer PUOLOP
Package ESOP-8
Category PMIC
Pins 8

CAD (KiCad official)

  • Symbol: PT4056
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm
  • 3D model: ESOP-8 (KiCad packages3D, STEP)
  • 3D model files: pt4056-etched.step / pt4056-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pt4056.step / pt4056.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: PUOLOP datasheet (11 pp, sha256 2cc8eaa7b83f45d8, retrieved 2026-08-17, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF