Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MTCH1010T-V

Microchip Tech · Touch Sensors · SOIC-8

MTCH1010T-V from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in Positive power supply pin, operating range 2 V to 5.5 V; also the required pull-up rail for the open-drain OUT0.
2 CH0 input Sensor electrode measurement input, connected to the touch electrode through a series resistor of 10 kΩ to 200 kΩ to reduce EMI/EMC.
3 SHIELD output Driven shield electrode output driver that reduces sensor load, increases sensitivity, shields against noise and provides water-tolerant touch.
4 OUT0 output Open-drain active-low touch indication output requiring an external pull-up to VDD; high-impedance when not in detect and driven low when the sensor is touched.
5 CFG0 input Response time configuration input (0 V to VDD in four bands A-D) selecting 300, 0 (minimum), 50 or 100 ms.
6 CFG1 input Oversampling configuration input (0 V to VDD in four bands A-D) selecting 8, 64, 32 or 16 samples per measurement cycle.
7 CFG2 input Touch sensitivity input with continuous adjustment from 0 V (lowest) to VDD (highest).
8 GND power_in Power supply negative (ground) pin.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8
Category Sensors
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating supply voltage VDD 2 5.5 V 15
Operating temperature range T -40 105 °C Standard temperature range 15
Ambient temperature under bias -40 105 °C 15
Storage temperature TStorage -65 150 °C 15
Pin voltage with respect to GND (max is VDD + 0.5) VPin -0.5 V Max printed as VDD + 0.5 15
I/O pin sink/source current IPin -40 40 mA 15
Maximum output current -15 15 mA 15
Power-on slope SRON 100 V/ms 15
POR threshold voltage on VDD falling VPOR 0.8 1.6 V VDD falls/rises at 0.5 V/ms or slower 16
POR threshold voltage on VDD rising VPOR 1.4 1.8 V VDD falls/rises at 0.5 V/ms or slower 16
BOD triggering level (falling/rising) VBOD 1.7 1.8 2 V 16
I/O pin drive strength VOL VOL 0.6 V VDD = 3.0V, IOL = 7.5 mA 16
I/O pin drive strength VOL VOL 1 V VDD = 5.0V, IOL = 15 mA 16
I/O pin drive strength VOH VOH 2.4 V VDD = 3.0V, IOH = 7.5 mA 16
I/O pin drive strength VOH VOH 4 V VDD = 5.0V, IOH = 15 mA 16
Input low-voltage on CFG1 pin as I/O (max is 0.3 × VDD) VIL2 -0.2 V Max printed as 0.3 × VDD 16
I/O pin drive strength on CFG1 pin as I/O VOL2 VOL2 0.6 V VDD = 3.0V, IOL = 0.25 mA 16
I/O pin drive strength on CFG1 pin as I/O VOL2 VOL2 1 V VDD = 5.0V, IOL = 0.5 mA 16
I/O pin drive strength on CFG1 pin as I/O VOH2 VOH2 2.4 V VDD = 3.0V, IOH = 0.25 mA 16
I/O pin drive strength on CFG1 pin as I/O VOH2 VOH2 4 V VDD = 5.0V, IOH = 0.5 mA 16
Pull-up resistor RP 20 35 50 kΩ 16
Hysteresis VHYS 25 mV 16
BOD detection time TBOD 7 µs Continuous 16
BOD detection time TBOD 1 ms Sampled, 1 kHz 16
BOD detection time TBOD 8 ms Sampled, 125 Hz 16
Start-up time TStart 40 µs Time from enable to ready 16
Rise time tRISE 2.5 ns VDD = 3.0V, load = 20 pF 16
Rise time tRISE 1.5 ns VDD = 5.0V, load = 20 pF 16
Fall time tFALL 2 ns VDD = 3.0V, load = 20 pF 16
Fall time tFALL 1.3 ns VDD = 5.0V, load = 20 pF 16
I/O pin capacitance except CH0, SHIELD, OUT0, and CFG0 pins CPIN 3 pF 16
I/O pin capacitance on CH0, SHIELD, OUT0, and CFG0 pins CPIN 10 pF 16

CAD (KiCad official)

  • Symbol: MTCH1010T-V
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mtch1010t-v-etched.step / mtch1010t-v-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mtch1010t-v.step / mtch1010t-v.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (31 pp, sha256 e1bb9c13c677e97c, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF