component
STM32G491CCT6
Public Made by Adomby adom
STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-48(7x7). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32G491CCT6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
STM32G491CCT6 from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply for the RTC and backup registers, operating from 1.55 V to 3.6 V. |
| 2 | PC13 | bidirectional | FT (5 V tolerant) I/O fed through the power switch, which sinks only 3 mA, so its output use is limited to 2 MHz maximum speed at 30 pF and it must not be used as a current source such as an LED driver; additional functions WKUP2, RTC_TAMP1, RTC_TS, RTC_OUT1. |
| 3 | PC14-OSC32_IN | bidirectional | FT I/O on the same power-switch limit as PC13 (3 mA, 2 MHz at 30 pF, no current-source use), also used as the 32 kHz oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | FT I/O on the same power-switch limit as PC13 (3 mA, 2 MHz at 30 pF, no current-source use), also used as the 32 kHz oscillator output OSC32_OUT. |
| 5 | PF0-OSC_IN | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA), also used as the high-speed oscillator input OSC_IN and ADC1_IN10; alternate functions include I2C2_SDA, SPI2_NSS/I2S2_WS, TIM1_CH3N. |
| 6 | PF1-OSC_OUT | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA), also used as the high-speed oscillator output OSC_OUT; additional functions ADC2_IN10, COMP3_INM, and alternate SPI2_SCK/I2S2_CK. |
| 7 | PG10-NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up; when configured as PG10 GPIO by option bytes it is FT tolerant (except during startup until option bytes are loaded), with alternate function MCO. |
| 8 | PA0 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, USART2_CTS, COMP1_OUT, TIM8_BKIN and additional ADC12_IN1, COMP1_INM, COMP3_INP, RTC_TAMP2, WKUP1 functions. |
| 9 | PA1 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH2, USART2_RTS_DE, RTC_REFIN and additional ADC12_IN2, COMP1_INP, OPAMP1_VINP, OPAMP3_VINP, OPAMP6_VINM functions. |
| 10 | PA2 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH3, USART2_TX, LPUART1_TX, UCPD1_FRSTX and additional ADC1_IN3, COMP2_INM, OPAMP1_VOUT, WKUP4/LSCO functions. |
| 11 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI1_CLK and additional ADC1_IN4, COMP2_INP, OPAMP1_VINM/OPAMP1_VINP functions. |
| 12 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM3_CH2, SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK and additional ADC2_IN17, DAC1_OUT1, COMP1_INM functions. |
| 13 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, TIM2_ETR, SPI1_SCK, UCPD1_FRSTX and additional ADC2_IN13, DAC1_OUT2, COMP2_INM, OPAMP2_VINM functions. |
| 14 | PA6 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM16_CH1, TIM3_CH1, SPI1_MISO, QUADSPI1_BK1_IO3, LPUART1_CTS and additional ADC2_IN3, OPAMP2_VOUT functions. |
| 15 | PA7 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM17_CH1, TIM3_CH2, SPI1_MOSI, QUADSPI1_BK1_IO2, UCPD1_FRSTX and additional ADC2_IN4, COMP2_INP, OPAMP1_VINP, OPAMP2_VINP functions. |
| 16 | PB0 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM3_CH3, TIM8_CH2N, TIM1_CH2N, QUADSPI1_BK1_IO1, UCPD1_FRSTX and additional ADC1_IN15/ADC3_IN12, COMP4_INP, OPAMP2_VINP, OPAMP3_VINP functions. |
| 17 | PB1 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM3_CH4, TIM8_CH3N, TIM1_CH3N, COMP4_OUT, QUADSPI1_BK1_IO0, LPUART1_RTS_DE and additional ADC1_IN12/ADC3_IN1, COMP1_INP, OPAMP3_VOUT, OPAMP6_VINM functions. |
| 18 | PB2 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with RTC_OUT2, LPTIM1_OUT, TIM20_CH1, I2C3_SMBA, QUADSPI1_BK2_IO1 and additional ADC2_IN12, COMP4_INM, OPAMP3_VINM functions. |
| 19 | VSSA | power_in | Ground for the analog domain (ADC, DAC, OPAMP, COMP, VREFBUF). |
| 20 | VREF+ | power_in | Positive reference voltage input for ADC/DAC, also available as the VREFBUF_OUT output; VREF+ must not exceed VDDA by more than 0.4 V. |
| 21 | VDDA | power_in | Analog supply: 1.62 V minimum when ADC or COMP is used, 1.71 V for DAC at 1 or 15 MSPS, 2.0 V for OPAMP, 2.4 V for VREFBUF, up to 3.6 V. |
| 22 | PB10 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH3, USART3_TX, LPUART1_RX, QUADSPI1_CLK, TIM1_BKIN, SAI1_SCK_A and additional OPAMP3_VINM function. |
| 23 | VSS | power_in | Digital ground reference; all VSS pins must be connected to the external ground within the permitted range. |
| 24 | VDD | power_in | Main digital and I/O supply, 1.71 V (guaranteed down to VBOR0 min after reset release) to 3.6 V. |
| 25 | PB11 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH4, USART3_RX, LPUART1_TX, QUADSPI1_BK1_NCS and additional ADC12_IN14, OPAMP6_VOUT functions. |
| 26 | PB12 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with I2C2_SMBA, SPI2_NSS/I2S2_WS, TIM1_BKIN, USART3_CK, FDCAN2_RX and additional ADC1_IN11, OPAMP6_VINP functions. |
| 27 | PB13 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with SPI2_SCK/I2S2_CK, TIM1_CH1N, USART3_CTS, FDCAN2_TX and additional ADC3_IN5, OPAMP3_VINP, OPAMP6_VINP functions. |
| 28 | PB14 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM15_CH1, SPI2_MISO, TIM1_CH2N, USART3_RTS_DE, COMP4_OUT and additional ADC1_IN5, OPAMP2_VINP functions. |
| 29 | PB15 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with RTC_REFIN, TIM15_CH2, TIM15_CH1N, COMP3_OUT, TIM1_CH3N, SPI2_MOSI/I2S2_SD and additional ADC2_IN15 function. |
| 30 | PA8 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with MCO, I2C3_SCL, I2C2_SDA, I2S2_MCK, TIM1_CH1, USART1_CK, TIM4_ETR, SAI1_CK2, SAI1_SCK_A. |
| 31 | PA9 | bidirectional | FT_fd I/O (5 V tolerant, Fm+ capable, USB Type-C PD dead-battery function) with I2C3_SMBA, I2C2_SCL, I2S3_MCK, TIM1_CH2, USART1_TX, TIM2_CH3, SAI1_FS_A and additional UCPD1_DBCC1 function; a high level here enables the UCPD CC1 pull-down on PB6. |
| 32 | PA10 | bidirectional | FT_da I/O (5 V tolerant, USB Type-C PD dead-battery function) with TIM17_BKIN, USB_CRS_SYNC, I2C2_SMBA, SPI2_MISO, TIM1_CH3, USART1_RX, TIM2_CH4, TIM8_BKIN, SAI1_D1, SAI1_SD_A and additional UCPD1_DBCC2, PVD_IN functions; a high level here enables the UCPD CC2 pull-down on PB4. |
| 33 | PA11 | bidirectional | FT_u I/O (5 V tolerant, with USB function) with SPI2_MOSI/I2S2_SD, TIM1_CH1N, USART1_CTS, COMP1_OUT, FDCAN1_RX, TIM4_CH1, TIM1_CH4, TIM1_BKIN2 and additional USB_DM function. |
| 34 | PA12 | bidirectional | FT_u I/O (5 V tolerant, with USB function) with TIM16_CH1, I2SCKIN, TIM1_CH2N, USART1_RTS_DE, COMP2_OUT, FDCAN1_TX, TIM4_CH2, TIM1_ETR and additional USB_DP function. |
| 35 | VSS | power_in | Digital ground reference; all VSS pins must be connected to the external ground within the permitted range. |
| 36 | VDD | power_in | Main digital and I/O supply, 1.71 V to 3.6 V. |
| 37 | PA13 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable); after reset it is the SWDIO-JTMS debug function with internal pull-up enabled, with alternate functions I2C1_SCL, IR_OUT, USART3_CTS, TIM4_CH3, SAI1_SD_B. |
| 38 | PA14 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable); after reset it is the SWCLK-JTCK debug function with internal pull-down enabled, with alternate functions LPTIM1_OUT, I2C1_SDA, TIM8_CH2, TIM1_BKIN, USART2_TX, SAI1_FS_B. |
| 39 | PA15 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable); after reset it is the JTDI debug function with internal pull-up enabled, with alternate functions TIM2_CH1, TIM8_CH1, TIM20_ETR, I2C1_SCL, SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_RX, UART4_RTS_DE, TIM1_BKIN, TIM2_ETR. |
| 40 | PB3 | bidirectional | FT I/O (5 V tolerant) that after reset is configured as the JTDO/TRACESWO debug alternate function, with alternate functions TIM2_CH2, TIM4_ETR, USB_CRS_SYNC, TIM8_CH1N, SPI1_SCK, SPI3_SCK/I2S3_CK, USART2_TX, TIM3_ETR, SAI1_SCK_B. |
| 41 | PB4 | bidirectional | FT_c I/O (5 V tolerant, USB Type-C PD capable); after reset it is the JTRST debug function with internal pull-up enabled and a 5.1 kOhm UCPD CC2 pull-down that can be disabled via UCPD1_DBDIS in PWR_CR3; additional UCPD1_CC2 function. |
| 42 | PB5 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM16_BKIN, TIM3_CH2, TIM8_CH3N, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI/I2S3_SD, USART2_CK, I2C3_SDA, FDCAN2_RX, TIM17_CH1, LPTIM1_IN1, SAI1_SD_B, UART5_CTS. |
| 43 | PB6 | bidirectional | FT_c I/O (5 V tolerant, USB Type-C PD capable) with TIM16_CH1N, TIM4_CH1, TIM8_CH1, TIM8_ETR, USART1_TX, COMP4_OUT, FDCAN2_TX, LPTIM1_ETR, SAI1_FS_B; after reset a 5.1 kOhm UCPD CC1 pull-down is active, activated by high level on PA9. |
| 44 | PB7 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM17_CH1N, TIM4_CH2, I2C1_SDA, TIM8_BKIN, USART1_RX, COMP3_OUT, TIM3_CH4, LPTIM1_IN2, UART4_CTS. |
| 45 | PB8-BOOT0 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) that doubles as the dedicated BOOT0 pin; it is recommended to set it out of analog mode after startup to limit consumption if left unconnected, with alternate functions TIM16_CH1, TIM4_CH3, I2C1_SCL, USART3_RX, FDCAN1_RX. |
| 46 | PB9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM17_CH1, TIM4_CH4, SAI1_D2, I2C1_SDA, IR_OUT, USART3_TX, COMP2_OUT, FDCAN1_TX, TIM8_CH3, TIM1_CH3N, SAI1_FS_A. |
| 47 | VSS | power_in | Digital ground reference; all VSS pins must be connected to the external ground within the permitted range. |
| 48 | VDD | power_in | Main digital and I/O supply, 1.71 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDA, VBAT, VREF+) | VDD - VSS | -0.3 | 4 | V | 71 | ||
| Input voltage on FT_xxx pins except FT_c | VIN | -0.3 | V | 71 | |||
| Input voltage on FT_c pins | VIN | -0.3 | 5.5 | V | 71 | ||
| Input voltage on TT_xx pins | VIN | -0.3 | 4 | V | 71 | ||
| Input voltage on any other pins | VIN | -0.3 | 4 | V | 71 | ||
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 71 | |||
| Variations between all the different ground pins (includes VREF-) | /VSSx-VSS/ | 50 | mV | 71 | |||
| Allowed voltage difference for VREF+ > VDDA | VREF+-VDDA | 0.4 | V | 71 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 150 | mA | 72 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 150 | mA | 72 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 72 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 72 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 72 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 72 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 72 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 72 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 72 | |||
| Injected current on FT_xxx, TT_xx, NRST pins | IINJ(PIN) | -5 | 0 | mA | 72 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 72 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 72 | ||
| Maximum junction temperature | TJ | 150 | °C | 72 | |||
| Internal AHB clock frequency | fHCLK | 0 | 170 | MHz | 73 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 170 | MHz | 73 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 170 | MHz | 73 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 73 | ||
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 73 | |
| Analog supply voltage | VDDA | 1.71 | 3.6 | V | DAC 1 MSPS or DAC 15 MSPS | 73 | |
| Analog supply voltage | VDDA | 2 | 3.6 | V | OPAMP used | 73 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | VREFBUF used | 73 | |
| Analog supply voltage | VDDA | 0 | 3.6 | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 73 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 73 | ||
| I/O input voltage, TT_xx | VIN | -0.3 | V | 73 | |||
| I/O input voltage, FT_c I/O | VIN | -0.3 | 5 | V | 73 | ||
| I/O input voltage, all I/O except TT_xx and FT_c | VIN | -0.3 | V | 73 | |||
| Ambient temperature, suffix 6 version, maximum power dissipation | TA | -40 | 85 | °C | Suffix 6 version, maximum power dissipation | 73 | |
| Ambient temperature, suffix 6 version, low-power dissipation | TA | -40 | 105 | °C | Suffix 6 version, low-power dissipation | 73 | |
| Junction temperature range, suffix 6 version | TJ | -40 | 105 | °C | Suffix 6 version | 73 | |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 76 |
| Average temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 76 | |
| Average voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 76 | |
| Internal reference voltage spread over the temperature range | ΔVREFINT | 5 | 7.5 | mV | VDD = 3 V | 76 | |
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25°C | 76 | |
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 74 | |
| Brown-out reset threshold 0, rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 74 |
| Brown-out reset threshold 0, falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 74 |
| Brown-out reset threshold 1, rising edge | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 74 |
| Brown-out reset threshold 1, falling edge | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 74 |
| Brown-out reset threshold 2, rising edge | VBOR2 | 2.26 | 2.31 | 2.35 | V | Rising edge | 74 |
| Brown-out reset threshold 2, falling edge | VBOR2 | 2.16 | 2.2 | 2.24 | V | Falling edge | 74 |
| Brown-out reset threshold 3, rising edge | VBOR3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 74 |
| Brown-out reset threshold 3, falling edge | VBOR3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 74 |
| Brown-out reset threshold 4, rising edge | VBOR4 | 2.85 | 2.9 | 2.95 | V | Rising edge | 74 |
| Brown-out reset threshold 4, falling edge | VBOR4 | 2.76 | 2.81 | 2.86 | V | Falling edge | 74 |
| Supply current in Run mode, Range 1 Boost, 170 MHz | IDD (Run) | 26.5 | 28 | mA | Code from flash, all peripherals disabled, 25°C | 78 | |
| Supply current in Sleep mode, Range 1 Boost, 170 MHz, Flash ON | IDD (Sleep) | 6.45 | 7.3 | mA | All peripherals disabled, 25°C | 86 | |
| Supply current in Stop 1 mode, RTC disabled, 3.0 V | IDD (Stop 1) | 68 | 440 | µA | RTC disabled, VDD = 3.0 V, 25°C | 88 | |
| Supply current in Stop 0 mode, RTC disabled, 3 V | IDD (Stop 0) | 175 | 580 | µA | RTC disabled, VDD = 3 V, 25°C | 89 | |
| Supply current in Standby mode, RTC disabled, no independent watchdog, 3 V | IDD (Standby) | 130 | 230 | nA | RTC disabled, VDD = 3 V, 25°C | 89 | |
| Supply current in Shutdown mode, RTC disabled, 3 V | IDD (Shutdown) | 42 | 89 | nA | RTC disabled, VDD = 3 V, 25°C | 91 |
CAD (KiCad official)
- Symbol:
STM32G491CCT6 - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32g491cct6-etched.step/stm32g491cct6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32g491cct6.step/stm32g491cct6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (197 pp, sha256
978130a7363b37d3, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).