Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

FT245RNL-REEL

FTDI · USB Converters · SSOP-28

FT245RNL-REEL from FTDI, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 D0 bidirectional FIFO Data Bus Bit 0.
2 D4 bidirectional FIFO Data Bus Bit 4.
3 D2 bidirectional FIFO Data Bus Bit 2.
4 VCCIO power_in +1.8V to +5.25V supply to the FIFO interface group pins; connect to 3V3OUT for +3.3V levels or to VCC for 5V CMOS levels in bus powered designs.
5 D1 bidirectional FIFO Data Bus Bit 1.
6 D7 bidirectional FIFO Data Bus Bit 7.
7 GND power_in Device ground supply pin.
8 NC unconnected No internal connection.
9 D5 bidirectional FIFO Data Bus Bit 5.
10 D6 bidirectional FIFO Data Bus Bit 6.
11 D3 bidirectional FIFO Data Bus Bit 3.
12 PWREN# output Goes low after the device is configured by USB, then high during USB suspend; should be pulled to VCCIO with a 10kΩ resistor when used to control an external P-channel MOSFET power switch.
13 RD# input Enables the current FIFO data byte on D0...D7 when low and fetches the next byte from the receive FIFO buffer when RD# goes from high to low.
14 WR input Writes the data byte on D0...D7 into the transmit FIFO buffer when WR goes from high to low.
15 USBDP bidirectional USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor to 3.3V.
16 USBDM bidirectional USB Data Signal Minus, incorporating internal series resistor.
17 3V3OUT power_out +3.3V output from the integrated LDO regulator, decoupled with 100nF, able to supply up to 50mA to external logic and usable to supply VCCIO.
18 GND power_in Device ground supply pin.
19 RESET# input Active low reset pin for an external device to reset the FT245RN; can be left unconnected or pulled up to VCC if not required.
20 VCC power_in +3.3V to +5.25V supply to the device core.
21 GND power_in Device ground supply pin.
22 TXE# output When high, do not write data into the FIFO; when low, data can be written by strobing WR high then low; tri-state during reset.
23 RXF# output When high, do not read from the FIFO; when low, data is available to read by strobing RD# low then high; tri-state during reset and becomes an input during suspend if Remote Wakeup is enabled.
24 NC unconnected No internal connection.
25 AGND power_in Device analogue ground supply for the internal clock multiplier.
26 TEST input Puts the device into IC test mode; must be tied to GND for normal operation, otherwise the device will appear to fail.
27 OSCI input Input 12MHz oscillator cell; optional and can be left unconnected for normal operation.
28 OSCO output Output from 12MHz oscillator cell; optional and can be left unconnected for normal operation if the internal oscillator is used.

Key specifications

Parameter Value
Manufacturer FTDI
Package SSOP-28
Category Communication Interface Chip
Pins 28

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature -65 150 °C 15
Floor Life (Out of Bag) At Factory Ambient (30°C / 60% RH) 168 hours At factory ambient (30°C / 60% RH); IPC/JEDEC J-STD-033A MSL Level 3 15
Ambient Temperature (Power Applied) -40 85 °C Power applied 15
VCC Supply Voltage VCC -0.5 6 V 15
DC Input Voltage, USBDP and USBDM -0.5 3.8 V 15
DC Input Voltage, High Impedance Bidirectional -0.5 V Printed max is + (VCC +0.5) 15
DC Input Voltage, All Other Inputs -0.5 V Printed max is + (VCC +0.5) 15
DC Output Current, Outputs 24 mA 15
Power Dissipation 500 mW VCC = 5.25V 15
VCC Operating Supply Voltage VCC1 3.3 5.25 V 15
VCCIO Operating Supply Voltage VCC2 1.8 5.25 V 15
Operating Supply Current, Normal Operation Icc1 15 mA Normal Operation 15
Operating Supply Current, USB Suspend Icc2 50 70 100 μA USB Suspend 15
3.3V regulator output 3V3 3 3.3 3.6 V 15
Output Voltage High (VCCIO = +5.0V, Standard Drive Level) Voh 3.2 4.1 4.9 V I source = 2mA 15
Output Voltage Low (VCCIO = +5.0V, Standard Drive Level) Vol 0.3 0.4 0.6 V I sink = 2mA 15
Input Switching Threshold (VCCIO = +5.0V, Standard Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 15
Input Switching Hysteresis (VCCIO = +5.0V, Standard Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 15
Output Voltage High (VCCIO = +3.3V, Standard Drive Level) Voh 2.2 2.7 3.2 V I source = 1mA 16
Output Voltage Low (VCCIO = +3.3V, Standard Drive Level) Vol 0.3 0.4 0.5 V I sink = 2mA 16
Input Switching Threshold (VCCIO = +3.3V, Standard Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Input Switching Hysteresis (VCCIO = +3.3V, Standard Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Output Voltage High (VCCIO = +2.8V, Standard Drive Level) Voh 2.1 2.6 2.8 V I source = 1mA 16
Output Voltage Low (VCCIO = +2.8V, Standard Drive Level) Vol 0.3 0.4 0.5 V I sink = 2mA 16
Input Switching Threshold (VCCIO = +2.8V, Standard Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Input Switching Hysteresis (VCCIO = +2.8V, Standard Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Output Voltage High (VCCIO = +1.8V, Standard Drive Level) Voh 1.32 1.62 1.8 V I source = 0.2mA 16
Output Voltage Low (VCCIO = +1.8V, Standard Drive Level) Vol 0.06 0.1 0.18 V I sink = 0.5mA 16
Input Switching Threshold (VCCIO = +1.8V, Standard Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Input Switching Hysteresis (VCCIO = +1.8V, Standard Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Output Voltage High (VCCIO = +5.0V, High Drive Level) Voh 3.2 4.1 4.9 V I source = 6mA 16
Output Voltage Low (VCCIO = +5.0V, High Drive Level) Vol 0.3 0.4 0.6 V I sink = 6mA 16
Input Switching Threshold (VCCIO = +5.0V, High Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Input Switching Hysteresis (VCCIO = +5.0V, High Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Output Voltage High (VCCIO = +3.3V, High Drive Level) Voh 2.2 2.8 3.2 V I source = 3mA 16
Output Voltage Low (VCCIO = +3.3V, High Drive Level) Vol 0.3 0.4 0.6 V I sink = 8mA 16
Input Switching Threshold (VCCIO = +3.3V, High Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Input Switching Hysteresis (VCCIO = +3.3V, High Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Output Voltage High (VCCIO = +2.8V, High Drive Level) Voh 2.1 2.6 2.8 V I source = 3mA 16
Output Voltage Low (VCCIO = +2.8V, High Drive Level) Vol 0.3 0.4 0.6 V I sink = 8mA 16
Input Switching Threshold (VCCIO = +2.8V, High Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Input Switching Hysteresis (VCCIO = +2.8V, High Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 16
Output Voltage High (VCCIO = +1.8V, High Drive Level) Voh 1.35 1.67 1.8 V I source = 0.4mA 17
Output Voltage Low (VCCIO = +1.8V, High Drive Level) Vol 0.12 0.18 0.35 V I sink = 3mA 17
Input Switching Threshold (VCCIO = +1.8V, High Drive Level) Vin 1 1.2 1.5 V ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 17
Input Switching Hysteresis (VCCIO = +1.8V, High Drive Level) VHys 20 25 30 mV ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO 17
RESET# and TEST Input Switching Threshold Vin 1.3 1.6 1.9 V 17
RESET# and TEST Input Switching Hysteresis VHys 50 55 60 mV 17
I/O Pins Static Output (High) UVoh 2.8 3.6 V RI = 1.5kΩ to 3V3OUT (D+), RI = 15KΩ to GND (D-) 17
I/O Pins Static Output (Low) UVol 0 0.3 V RI = 1.5kΩ to 3V3OUT (D+), RI = 15kΩ to GND (D-) 17
Single Ended Rx Threshold UVse 0.8 2 V 17
Differential Common Mode UCom 0.8 2.5 V 17
Driver Output Impedance UDrvZ 26 29 44 Ohms 17
Frequency of Operation 11.98 12 12.02 MHz Internal clock oscillator (see Note 1) 17
Clock Period 83.19 83.33 83.47 ns 17
Duty Cycle 45 50 55 % 17
Thermal Resistance Junction-to-Ambient (FT245RNL) ΘJA 81.36 °C/W 18
Thermal Resistance Junction-to-Case (FT245RNL) ΘJC 49.58 °C/W 18

CAD (KiCad official)

  • Symbol: FT245RNL-REEL
  • Footprint: Package_SO:SSOP-28_5.3x10.2mm_P0.65mm
  • 3D model: SSOP-28 (KiCad packages3D, STEP)
  • 3D model files: ft245rnl-reel-etched.step / ft245rnl-reel-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft245rnl-reel.step / ft245rnl-reel.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FTDI datasheet (36 pp, sha256 45dc0b8b61dc4076, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF