Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS54260MDGQTEP

Texas Instruments · DC-DC Converters · HVSSOP-10-EP-0.5mm

TPS54260MDGQTEP from Texas Instruments, in a HVSSOP-10-EP-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BOOT output A bootstrap capacitor is required between BOOT and PH; if its voltage falls below the minimum required by the output device, the output is forced to switch off until the capacitor is refreshed.
2 VIN power_in Input supply voltage, 3.5 V to 60 V.
3 EN input Enable pin with internal pull-up current source; pull below 1.2 V to disable, float to enable, and adjust the input undervoltage lockout with two resistors.
4 SS/TR input Slow-start and tracking pin; an external capacitor sets the output rise time, and because this pin overrides the internal reference it can be used for tracking and sequencing.
5 RT/CLK input Resistor timing and external clock pin that sets the switching frequency with a resistor to ground, or becomes a synchronization input when pulled above the PLL upper threshold.
6 PWRGD output Open-drain power-good output that asserts low if the output voltage is low due to thermal shutdown, dropout, over-voltage or EN shutdown.
7 VSENSE input Inverting node of the transconductance (gm) error amplifier, used for the output voltage feedback divider.
8 COMP output Error amplifier output and input to the output switch current comparator; frequency compensation components connect to this pin.
9 GND power_in Ground.
10 PH input The source of the internal high-side power MOSFET, and the switching node that the BOOT capacitor references.
11 PowerPAD power_in GND pin must be electrically connected to the exposed pad on the printed circuit board for proper operation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HVSSOP-10-EP-0.5mm
Category Power Management (PMIC)
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage (VIN) VIN -0.3 65 V 4
Input voltage (EN) EN -0.3 5 V 4
Input voltage (VSENSE) VSENSE -0.3 3 V 4
Input voltage (COMP) COMP -0.3 3 V 4
Input voltage (PWRGD) PWRGD -0.3 6 V 4
Input voltage (SS/TR) SS/TR -0.3 3 V 4
Input voltage (RT/CLK) RT/CLK -0.3 3.6 V 4
Output voltage (BOOT-PH) BOOT-PH -0.3 8 V 4
Output voltage (PH) dc PH -0.6 65 V 4
Output voltage (PH) transient PH -1 65 V 200 ns 4
Output voltage (PH) transient PH -2 65 V 30 ns 4
PH maximum dc voltage PH -0.85 V TJ = -40°C 4
Voltage difference PAD to GND -200 200 mV 4
Source current (EN) 100 μA 4
Source current (BOOT) 100 mA 4
Source current (VSENSE) 10 μA 4
Source current (RT/CLK) 100 μA 4
Sink current (COMP) 100 μA 4
Sink current (PWRGD) 10 mA 4
Sink current (SS/TR) 200 μA 4
Operating junction temperature TJ -55 150 °C 4
Storage temperature Tstg -65 150 °C 4
Operating junction temperature TJ -55 150 °C 4
Operating input voltage VIN 3.5 60 V 5
Enable threshold voltage 1.14 1.25 1.36 V No voltage hysteresis, rising and falling, 25°C 5
Shutdown supply current 1.3 10 μA EN = 0 V, 3.5 V ≤ VIN ≤ 60 V 5
Operating nonswitching supply current 138 200 μA VSENSE = 0.83 V, VIN = 12 V 5
Voltage reference 0.792 0.8 0.808 V TJ = 25°C 5
Voltage reference 0.78 0.8 0.82 V 5
High-side MOSFET on resistance 200 410 mΩ VIN = 12 V, BOOT-PH = 6 V 5
Error amplifier source/sink current -27 27 μA V(COMP) = 1 V, 100 mV overdrive 5
Current limit threshold 3.5 6.1 A VIN = 12 V 6
Switching frequency range using RT mode fSW 100 2500 kHz 6
Switching frequency fSW 450 581 720 kHz RT = 200 kΩ 6
Switching frequency range using CLK mode fSW 300 2200 kHz 6
RT/CLK high threshold 1.9 2.2 V 6
RT/CLK low threshold 0.5 0.7 V 6
Minimum VIN for defined PWRGD output 0.95 1.9 V V(PWRGD) < 0.5 V, II(PWRGD) = 100 μA 6
Junction-to-ambient thermal resistance (standard board) RθJA 62.5 °C/W Standard board 5
Junction-to-ambient thermal resistance (custom board) RθJA 57 °C/W Custom board 5
Junction-to-case (top) thermal resistance RθJC(top) 83 °C/W 5
Junction-to-board thermal resistance RθJB 28 °C/W 5
Junction-to-top characterization parameter ψJT 1.7 °C/W 5
Junction-to-board characterization parameter ψJB 20.1 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 21 °C/W 5

CAD (KiCad official)

  • Symbol: TPS54260MDGQTEP
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: HVSSOP-10-EP-0.5mm (KiCad packages3D, STEP)
  • 3D model files: tps54260mdgqtep-etched.step / tps54260mdgqtep-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps54260mdgqtep.step / tps54260mdgqtep.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (54 pp, sha256 f53e781ce62a96ff, retrieved 2026-11-10, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF